Question about 2000 Ford Focus

2 Answers

My heater fan only works on setting 4,the other three do no work. Please can you tell me what the problem is. Many thanks

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 8,190 Answers

Your resistor has failed, and the swtich may also be bad. See my tips at http://www.fixya.com/cars/r6234839-doesn_t_heater_or_air_conditioner_blow .

I could not find the location of your resistor, but I believe you will find it under the dash on the passenger side. Please let me know if you have questions.

Posted on Oct 08, 2010

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 20 Answers

The swith contain four steps from inside it looks like the contact inside the switch are out of order if the step four is working now later on will stop because this is the life time for the switch and it is too difficult to reassemble it once it is opened it needs an expert

Posted on Oct 28, 2010

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

moparownr
  • 667 Answers

SOURCE: heater fan only works on fastest speed

Your blower motor resistor has gone bad, it should be located next to your blower motor in the car, held in place with a couple of screws, remove it and replace it. The resistor is responsible for making the blower motor run at slower speeds than high or (4). Let me know if this helps.

Posted on Jun 16, 2009

jdfrail27
  • 15 Answers

SOURCE: interior fan only working on high #4

it only takes a sprk to blow the heat and ac switch out such as installing a stero ormayby rounding the plastic off behind the switch

Posted on Jan 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, The heater fan only works on setting 4. I have just replaced the Heater motor resister, but the problem is still there. I've checked the fuses all seem fine. Thanks in advance for your help.


can you tell me the type of swich you have knob type or electric type knob type the switch needs to be replaced. electric type the control board has burnt out.

Oct 02, 2013 | Opel Vectra Cars & Trucks

1 Answer

1999 jeep wrangler heater blower


you need to change the resister block for the fan. it is located on the heater duct near the fan... there is a connector on it and two or three screws holding it in.

Robert

Please take a moment to rate this solution thanks

Feb 21, 2009 | Jeep Wrangler Cars & Trucks

1 Answer

I can't find the heater fan relay on my 1991 Honda Accord EX 4 dt


you mean the cooling fan? for the rad the relay is under the hood by the battery in the fuse and relay box

Feb 19, 2009 | 1992 Honda Accord

1 Answer

2000 sebring convertible - heater fan only blows on full blast,


you need to replace the resister block for the fan speeds... it is located in/on the duct work near the fan. you will see a connector and two or three screws holding it in.

Robert

Please take a moment to rate this solution thanks

Jan 28, 2009 | 2000 Chrysler Sebring

2 Answers

Heater blower motor works intermittently


I would replace the blower motor, this sounds like a motor brush problem inside the motor itself.

Jan 24, 2009 | 1993 Pontiac Bonneville

1 Answer

Heater fan cotrol;


Could be a fuse..but more than likely you need to replace the blower motor

Jan 14, 2009 | 1998 Ford Escort

2 Answers

Interior fan only working on high #4


it only takes a sprk to blow the heat and ac switch out such as installing a stero ormayby rounding the plastic off behind the switch

Jan 12, 2009 | 1999 Mercury Cougar

1 Answer

Corolla heater fan not working on low


Replace the switch... get one from the junkyard...

Dec 27, 2008 | 1989 Toyota Corolla 2 Door

2 Answers

Camry 1991 4 cyl.LE.Blower fan in dashboard stopped working


heater fan speed switch located in heater box by passengers feet up in heater box one plug on it cant miss two screws hold it in!!!!

Dec 27, 2008 | 1995 Toyota Camry

Not finding what you are looking for?
2000 Ford Focus Logo

483 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...