Question about 2000 Kia Sephia

1 Answer

High beam can't on. - 2000 Kia Sephia

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Expert
  • 200 Answers
Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Saturn aura wont start after trying to put rt.low lowbeam replacement


On the inside of the lid is a diagram .
The headlamps may be turned ON 2 different ways. First, when the driver places the headlamp switch in the HEADLAMP position, for normal operation. Second, with the headlamp switch placed in the AUTO position, for automatic lamp control (ALC). During ALC, the headlamps will be OFF in daylight conditions, or low beam operation in low light conditions. Battery positive voltage is supplied to the low beam relay and the high beam relay in the underhood fuse block. When low beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the low beam relay. This activates the relay and the relay supplies voltage to the left hand low beam headlamp through the LH LOW BEAM fuse and to the right hand low beam headlamp through the RH LOW BEAM fuse. Ground for the left hand low beam headlamp is provided at G101. Ground for the right hand low beam headlamp is provided at G102. When high beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the high beam relay. This activates the relay and the relay supplies voltage to the left hand high beam headlamp through the LH HIGH BEAM fuse and to the right hand high beam headlamp through the RH HIGH BEAM fuse. Ground for the left hand high beam headlamp is provided at G101. Ground for the right hand high beam headlamp is provided at G102.

Aug 14, 2017 | Saturn Cars & Trucks

1 Answer

While low beams on the left high beams stays on dim light but wen I turn high beams on they work fine


It could be driving lights mode instead of low beam. Check connections.

Jun 16, 2017 | Cars & Trucks

1 Answer

Wiring diagram for high beam on actros 3848


back for high beam forward for low beam
high beam will not work in low beam position

Dec 22, 2016 | Mercedes-Benz Mercedes Bentz Actros Semi...

1 Answer

2010 impala high beams do not come on, light on dash comes on, replaced bulbs still don't work, checked all fuses, look good


High Beam Headlamp Operation
Battery voltage is applied at all times to the coil and switch sides of the HIGH BEAM PCB Relay located in the underhood fuse block. When the headlamp dimmer switch is placed in the high beam position, the headlamp dimmer switch signal circuit to the BCM is pulled low signaling the headlamp high beam request. In response to this signal, the BCM applies ground through the high beam relay control circuit energizing the high beam relay. With the high beam relay energized, battery voltage is applied through the switch side of the relay, the left and right high beam fuses, and the high beam supply voltage circuits illuminating the high beam headlamps. At the same time the BCM sends a GMLAN serial data message to the instrument panel cluster (IPC) requesting the IPC to illuminate the high beam indicator. Ground for the left headlamp is provided at G101 and the right headlamp at G100.

Nov 23, 2016 | 2010 Chevrolet Impala

2 Answers

Low beams don't work; High beams fine. Not the


the high beam switch is at fault
A new one is needed
The directional lever you pull up on to switch to high and low connects to a rod which is going to the high beam switch at the mid section of the steering coluum. It is a headache to change for your on your head replacing this part

May 24, 2010 | 2004 GMC Envoy

1 Answer

My high beams dont work.


high beam switch is faulty look at getting a new stalk.....

Aug 25, 2009 | 1990 Toyota Land Cruiser

1 Answer

How can i disconnect the high beams because when i turn my normal lights on the high beams come on. I need to know how I can disconnect them.


there are 3 wires going to each headlamp,a ground,a low beam,and a high beam.. cut the high beam wire, and do both sides .and if you want high beams to work,wire both sides to a single throw double pole switch for the high beams to turn on and off.

Jul 22, 2009 | 1991 Toyota Tercel

1 Answer

High beam


replace the switc and also ck the hi beam relay

Nov 23, 2008 | 1986 Toyota 4Runner

Not finding what you are looking for?
2000 Kia Sephia Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

79847 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...