Question about 2000 Nissan Frontier

Open Question

2000 nissan frontier clucth repair specs need flywheel torque

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
joecoolvette
  • 5660 Answers

SOURCE: Bolt torque specs for flywheel, pressure plate,

1.Flywheel - 61 to 69 Foot Pounds
2.Pressure Plate - 25 to 33 Foot Pounds
3.Bell Housing - No specs found. I would say 25 to 35 foot pounds should be sufficient.

Bolts clean on ->flywheel to crank, ->pressure plate to flywheel, and ->bell housing to back of engine, I would use TWO drops of Loctite Red threadlocker, on ALL of these bolts.

Hope you have an alignment tool for your clutch disk when you install it. Auto parts stores sell the plastic one's cheap! Saves a LOT of headaches!

Tighten the pressure plate EVENLY! Snug the bolts down until they just TOUCH, then go in a criss-cross pattern when tightening. Do the tightening in incremental stages! You turn one bolt one thread, you go across to the opposite side, and turn that bolt one thread. Keep criss-crossing so the pressure plate goes down EVENLY. (YES, it's a pain in the keister!)

If NOT, you'll have a warped pressure plate, and it will be junk!
Thanks for letting me say that, I feel better.

Posted on Jul 07, 2009

Ad

SOURCE: Torque spec for flywheel bolt: Isuzu 2.5 diesel engine

normally 110 nueton metres. use nut lock and once you have torqued you will feel if you have to tighten it a bit more.

Posted on Aug 15, 2008

chuck943
  • 783 Answers

SOURCE: torque specs foe 4.9 ford f150 flywheel

75-85 ft lbs

Posted on Mar 04, 2009

outdoorsman5
  • 631 Answers

SOURCE: head bolt torque specs for 2000 dodge neon 2.0 SOHC

I have the specs and diagrams. If you want me to send them to you, give me your email address. Outdoorsman592003@yahoo.com

Posted on Sep 05, 2009

  • 3640 Answers

SOURCE: engine repair code P0325

po325--ignition system or missfire.

Posted on Sep 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

On Nssan Frontier 1999 2.4L I am replacing the waterpump and fan clutch. I need to know the torque measurements for the pump- and clutch nuts.


Go to autozone.com and they have free online books you can look it up just enter make model and engine type

hope this helps mike

Jul 20, 2016 | 1999 Nissan Frontier

1 Answer

What is the torque setting for nissan navara v6 4lt2007 flywheel torque


there are 2 sets of torque specs for flywheel bolts as there are 2 different fly wheels in use with different bolts for each
go google and type in--torque specifications for nissan navara flywheel bolts and fins a site relevant to you application
it could be 61-69 ft/lbs a or 90 ft lbs depending on the flywheel and the vehicle 2wd or 4wd

Sep 30, 2015 | Nissan Cars & Trucks

1 Answer

2004 nissan frontier head torque specs


You should have torque to yield bolts there. That means single use - you need to buy new bolts. Then, you would torque to spec (maybe 10-12 ft. lbs.) then an additional 65 degrees of tightening rotation.
Call your local auto parts supplier.
Repair Guides Specifications Torque Specifications AutoZone com

Feb 26, 2015 | Nissan Frontier Cars & Trucks

1 Answer

Nissan frontier starter binds the flywheel


You need to put shims in between the starter and the engine block.You should be able to pick them up at your local auto parts store.

Oct 31, 2012 | Nissan Frontier Cars & Trucks

1 Answer

Replace valve cover gaskets on a 2000 frontier v 6


torque specs for the rocker cover (valve cover) screws:
9 - 26 inch lbs
step one- 9 in lbs step 2- 18 in lbs step 3- 26 in lbs
tightening order (see diagram below)


2aa1d8f9-c423-4221-bbed-38a4f9049ad6.png

May 27, 2010 | 2000 Nissan Frontier

2 Answers

I need the Torque Specs for a Nissan Q-R 2.5 Engine?


Nissan QR 2.5 engine produces a torque of 180 ft·lbf (244 N·m) of torque at 4000 rpm .

Oct 11, 2009 | 2003 Nissan Sentra

Not finding what you are looking for?
2000 Nissan Frontier Logo

Related Topics:

610 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...