Question about 1994 Ford Tempo

1 Answer

I installed a new starter silinode in my 94 ford temp 4 cylinder an the only way i can start the car is to touch the 2 gold bolts togeather. and i just bout a new battery an alternator but after a couple hours the car dies

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 491 Answers

Your ignition switch could be faulty

Posted on Oct 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install flywheel ford f150 6 cylinder engine


Pull drive shaft 4 bolts next pull transmission cross member 4 bolts pull transmission lines 2 pull all wiring 2 pull transmission inspection cover 4 bolts pull transmission 6 bolts pull flywheel 6 bolts install new and reverse process

Aug 12, 2014 | 2005 Ford F-150 SuperCab

1 Answer

How to install a clutch kit on my 1994 mitsubishi mighty max


Disconnect the battery, disconnect the Hydraulic Line from the Slave Cylinder, Remove the Starter (2 bolts, 2 wires. Bolts are 14mm, 1 wire is 12mm, 1 plugs in), Remove the Driveshaft(s) (4 12mm bolts) Remove the 6 bolts from the bellhousing (4 are 14mm, 2 are 10mm)
Remove the bolt from the Transfer Case Mount, 12mm (only if it's a 4WD, if it's 2WD this doesn't apply), remove the 2 bolts that hold the Transmission Mount to the Crossmember (12mm or 14mm, it varies)
Slide the transmission back on the crossmember, away from the engine, I recommend running a ratchet strap across the frame to balance the transmission.
Remove the Pressure Plate from the Flywheel (Six 10mm bolts), Inspect the Pilot Bearing (if it needs replaced, you'll need to remove the Flywheel which is held on with six 18mm bolts, drive out the old bearing and drive in the new one, reinstall the flywheel, using Threadlocker on the bolts, torque the bolts to 100 ft lbs) Install the new clutch disc and Pressure Plate, with the centering tool inserted through the disc into the pilot bearing. Use thread locker on the pressure plate bolts and torque them to 20 ft lbs. Remove the centering/alignment tool after you've bolted it together
Remove old Throw Out bearing from input shaft on the transmission and slide the new one on. Slide the Transmission forward (make sure the input shaft slides into the pilot bearing, don't force the transmission into place or you could damage the clutch disc or break the input shaft) Torque the Bellhousing Bolts to 40 ft lbs (4 14mm bolts), Torque the 2 10mm bolts to 14 ft lbs, Install the Starter (torque bolts to 23 ft lbs), Reconnect Hydraulic Line to Slave Cylinder. Torque Transmission Mount Bolts to 30 ft lbs.
Reinstall Driveshafts, torque bolts on flange/yoke to 40 ft lbs. Fill Clutch Master Cylinder with DOT-3 Brake & Clutch Fluid, Open Bleeder Screw on Slave Cylinder and bleed the air out of the system, close bleeder screw.
Reconnect the wires to the Starter, Reconnect the battery.

Aug 24, 2011 | Mitsubishi Mighty Max Cars & Trucks

2 Answers

How to remove a starter in 1987 ford taurus?


Underneath the car, for a front wheel drive, it will be toward the front of the engine a long cylinder shaped part with another cylinder with wires going onto it. take the wires off first, paying close attention to their placement, then you remove the mounting bolts and pull it out, it's that easy dude, you can also find a video on how to do it on youtube.

Jun 09, 2011 | 1987 Ford Taurus

1 Answer

Firing order diagram for 94 vw gold


For the 1994 VW Golf:
I do not know if you have the 1.8L SOHC In-Line 4-Cylinder or the 2.0L SOHC In-Line 4-Cylinder; however I have included both below:

For the 1.8L SOHC In-Line 4-Cylinder
Firing Order:
1-3-4-2
Cylinders:
..........(back).........
|...1....2....3....4...|
..........(front)
Distributor:
...(back)
(+)....1
...2.........3
........4...(+)-screw

For the 2.0L SOHC In-Line 4-Cylinder:
Firing Order:
1-3-4-2
Cylinders:
..........(back)..........
|...1....2....3....4...|
.........(front)
Distributor:
......(back)
.....2.......1
(+)............(+)-screws
.....4.......3
......(front)

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

May 27, 2010 | 1994 Volkswagen Golf

1 Answer

Wiring for the starter on a 94 ford tempo


There is just one wire bolted to the starter with usually a 10mm bolt.

May 09, 2010 | 1994 Ford Tempo

1 Answer

Torque specs for cylinder head on a 200 ford focus with 2.0 ltr single overhead cam. and for connecting rod... Thank you much.


  1. CAUTION: Always install new cylinder head bolts. NOTE: Lubricate the cylinder head bolts with Super Premium 5W 30 SAE X0-5W 30-QSP or equivalent meeting Ford specification WSS-M2C153-G prior to installation. Install the cylinder head assembly and tighten the cylinder head bolts in the following sequence.
  1. Tighten all bolts in a single sequence to 50 Nm
  2. Back the bolts off 1/2 turn.
  3. Tighten the bolts in sequence shown to 50 Nm .
  4. Rotate all the bolts in a single sequence an additional 180 degrees in two steps of 90 degrees each.
9 3 1 5 7
8 6 2 4 10 sequence for head


Spec for rod 38Nm

May 07, 2010 | 2000 Ford Focus

1 Answer

How to Remove 94 Ford XLT starter motor & solenoid


  1. Disconnect the negative battery cable.
  2. Raise the front of the vehicle and install jackstands beneath the frame. Firmly apply the parking brake and place blocks in back of the rear wheels.
  3. Tag and disconnect the wiring at the starter.
4. Remove the starter mounting bolts and remove the starter.

To install:

  1. Position the starter motor against the engine and install the mounting bolts. Tighten the mounting bolts to 15-19 ft. lbs. (21-27 Nm).
  2. Install the starter solenoid connector by pushing it straight on. Ensure that the connector locks in position with a notable click.

Install the starter cable nut to the starter solenoid B-terminal. Tighten the nut to 80-123 inch lbs. (9-14 Nm).
  1. Connect any remaining wiring to the starter motor.
  2. Lower the front of the vehicle and remove the wheel blocks.
  3. Connect the negative battery cable.


Mar 31, 2010 | 1994 Ford Ranger Supercab

1 Answer

Replacing a new starter on a 93 isuzu rodeo


Don't know what size motor you have because you didn't post it so please pick the proper one:

This is for the 4 cylinder motor--

8e64f3e.gif
4-cylinder engine starter connections



  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. If equipped, it may be necessary to disconnect and remove the EGR pipe to access all the starter bolts.
  4. Tag and disconnect the starter battery and control wiring at the starter.
  5. If equipped, remove the starter bracket and/or heat shield.
  6. Remove the starter-to-engine bolts.
  7. Move the starter away from the engine and down to remove from the vehicle. Some starter may be installed with shims between the starter and engine. When the starter is removed, these shims may fall out. Do not loose them.
To install:
  1. Install the starter and shims, if equipped to the engine. Align the mounting bolt holes and insert the bolts. Hand-tighten the bolts.
  2. Tighten the starter mounting bolts to 30–34 ft. lbs. (39–44 Nm).
  3. Install the starter bracket and/or heat shield, if equipped.
  4. Connect the battery and starter control electrical wires to the starter.
  5. If the EGR pipe was removed, install it.
  6. Lower the vehicle.
  7. Connect the negative battery cable.
  8. Start the vehicle to make sure the starter functions correctly.
This is for the V6 motor--

8fdc27b.gif
6-cylinder engine starter installation


  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Label and disconnect the battery and starter control wires from the starter.
  4. If equipped, remove the starter bracket and/or heat shield.
  5. Remove the starter-to-engine mounting bolts.
  6. Lower the starter from the engine. If any shims are present, keep them for reinstallation purposes.
To install:
  1. Install the starter and shims, if equipped, to the engine. Tighten the mounting bolts to 30–34 ft. lbs. (39–44 Nm).
  2. Install the starter bracket and/or heat shield, if equipped.
  3. Reconnect the electrical connectors to the starter.
  4. Lower the vehicle.
  5. Connect the negative battery cable.
  6. Start the vehicle to make sure the starter functions correctly.

Nov 19, 2009 | 1993 Isuzu Rodeo

1 Answer

How to replace starter 5.4l


The starter is bolted to the bell housing.
Is has a positive cable from starter solenoid.

1. Remove the negative battery cable at the battery.
2. remove the power cable from the starter.
3. remove the starter mounting bolts (typically only 2 bolts)
4. Install new starter. Hand tighten mounting bolts
5. Secure both bolts to about 35 Lbs of torque
6. Connect power cable.
7. Connect the negative battery cable at the battery.
8. Test (start the car).

Oct 15, 2009 | 1999 Ford Expedition

1 Answer

How do you change the starter on a 2005 ford expedition


The answer will vary - depending on the engine you have...Generally, you first remove the neg. cable from the battery.
Then you remove the 2 (or 3) wires from the starter.
Then you remove the 2 bolts that hold the starter to the bell housing.
Lube the bolts (must be clean too) - place the new starter... install the bolts... Torque to about 30 lbs .... the reconnect the wires to the new starter.
Finally reconnect the neg battery cable and start your Expedition!!

Oct 09, 2009 | 2005 Ford Expedition

Not finding what you are looking for?
1994 Ford Tempo Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75235 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...