Question about 2003 GMC Yukon XL

2 Answers

I'm changing a front whell bearing/hub assembly on 2003 yukon xl 1500 4wd and need to know if the brake caliber is pressed on and off or if I can remove it without a press?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

I agree w/ Dieselpro, once you take off the wheel the only thing you need to do is by using a breaker bar, unloosing the 2 nuts that is holding the calibor bracket and then you can remove the calibor, brakes and calibor all as one unit. The rotor will side off freely afterwards.

Posted on Mar 19, 2013

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 183 Answers

Calipher just unbolts.. Might need a 1/2 inch breaker bar and I think a 21 or 22 mm socket.. There on quite tight.

Posted on Oct 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace front hub assembly 2002 Suzuki XL7


the front wheel bearing hub?
XL-7 (the dash matters)
my wild guess, is the questions was
what are all steps to do this job. and tools.
that?
RTM?

https://suzukipitstopplus.com/Products/10056-2002-grand-vitara-xl-7-service-manual.aspx

http://www.fixkick.com/hubs/FW_BEARINGS.html#newer
the link shows all years, and variances.

here is a photo review, that is accurate up to
1998, and beyond , if you skip the bearing service parts. as yours are INTEGRATED
and NON-serviceable.
http://www.fixkick.com/hubs/FW_BEARINGS.html


the photo 6a and B
shows removing the hub,
so do that , buy a new hub and put it back
the same way, using the tool stated
at the stated ranges of torque
123-180 ft/lbs.
this range allows you to get the screws into the locking rings.

Dec 11, 2016 | 2002 Suzuki XL-7

1 Answer

I have a 2007 yukon denali xl, I got my front brakes and right wheel hub changed. When he got doney brake lights in the back of the truck wI'll not shut off. Brake light switch did nothing to help..


Who put the front brakes an wheel hub bearing on the vehicle ? A qualified repair shop ? A friend ? The front brakes an wheel hub would have nothing to do with the brake lights . An the brake light switch is an input to the BCM - body control module .
Stop Lamps
When the driver presses the brake pedal, the switch contacts open and battery positive voltage is interrupted to the BCM. The BCM then supplies voltage to both the turn/stop lamp supply voltage circuit and trailer rear turn/stop lamp supply voltage circuits. The BCM also supplies voltage to the CHMSL though a dedicated circuit.
I suggest you take it back to who did the front brakes , or a quailfied repair shop .
DTC B3445 00: Stop Lamp Circuit - DO you know what a DTC is ? diagnostic trouble code !
Diagnostic Fault Information
Circuit
Short to Ground
Open/High Resistance
Short to Voltage
Signal Performance
Stop Lamp Supply Voltage
B3445 00
--
Stop Lamps Inoperative
Stop Lamps Always On
Circuit/System Testing
Disconnect the stop lamps and test the individual stop lamp assemblies for internal shorts between all terminals.
? If a short between terminals is found, replace the stop lamp socket or circuit board as applicable.
Test the stop lamp supply voltage circuit for a short to ground.
? If all circuits/connections test normal, replace the BCM.

Nov 09, 2016 | 2007 GMC Yukon XL Denali

1 Answer

What are the torque settings on the front wheel hub bearing assembly for a 2003 gmc yukon denali xl?


155 Ft/Lb is the correct Torque

http://www.speedwayautoparts.com/Torque%20Specks.pdf

Mar 23, 2013 | 2006 GMC Yukon Denali

1 Answer

Is there any grease to be applied on wheels bearing on GMC Yukon 2003 ,


It comes as a bearing hub and assemble, As for applying grease its sealed

Apr 25, 2011 | 2003 GMC Yukon XL

1 Answer

When applying brake last bit before stopping judders like anti lock stuck


front wheel bearings going bad. this is common. the speed sensor is part of assembly. it will get real bad and you will have no brakes at low speeds, turning is worse. replace both front hubs. not cheap but will save headaches

Feb 27, 2011 | 2000 GMC Yukon XL

1 Answer

Replace front hub assembly.


Replacing the front wheel bearing/hubs can be a big job for the inexperianced. Briefly...
Remove tire/wheel
Remove brake caliper assembly, do not remove brake line.
Remove caliper bracket.
Remove brake rotor.
Unplug ABS sensor.
Remove the large axle nut.
Press axle out of bearing (may need special tool)
Remove the 3 bearing bolts and remove bearing.

May 19, 2010 | 2003 Chevrolet Impala

1 Answer

Do you have a description or directions on how to change a front passenger side wheel hub bearing on a 4 wheel drive 2003 yukon xl 1500???


Honestly I wouldn't attempt to do this unless your a trained automotive technician, hub bearings are... a b#&ch without the right tools

Apr 30, 2010 | 2003 Chevrolet Suburban 1500

2 Answers

Replace front left wheel berring on 2002 GMC Yukon


do not replace only the bearing. replace hub assembly. remove rim/tire , remove caliper, mounting plate, rotor. . un bolt hub assembly, unplug abs. remove front axle nut if 4x4. you may need to rent the axle nut remove kit and hub puller. pull out hub. drive axle reward out of hub. install new part. do not torque hub over 90lbs. check with parts sell for spec

Jan 03, 2010 | 2002 GMC Yukon XL

2 Answers

Change front wheel bearings


u will need to remove the brake cailper and the the brake rotor, then the hub retaining nut, that is a large metric nut, the bearing and hub must come off, then u will need to take this hub to a machine shop or the dealer and have the new bearing pressed in.
BCA/NATIONAL Part # 510078 moreinfo.gif {Ball Bearing Bore=1.5354" Outer Diameter=2.9134" Width=1.4173"}
Front Wheel PRICE: $47.99, PART SOURCE: Rockauto.com

3bcf37f.jpg

Mar 12, 2009 | 2003 Hyundai Tiburon

Not finding what you are looking for?
2003 GMC Yukon XL Logo

280 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...