Question about 2000 Nissan Altima

1 Answer

Fan switch, works only in the 4 position - 2000 Nissan Altima

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

Its your temp limited switch give these websites a try www.alldatadiy.com and www.autozone.com for the most part its close to the blower motor itself if all fails stop by your local library and get your hands on a Haynes auto repair manual for your car wish you the best of luck Michigan Man.

Posted on Oct 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to trouble shoot heat/ a/c fan switch.


Will your blower fan kick on in the medium position by chance? Med/ med high..if it is a 4 position switch, does it operate in the number 3 position? If so it is probably your blower motor resistor. If not, I would test the blower motor itself. Since the compressor kicks on when you turn the fan on, I would think the switch is working.

Jun 11, 2015 | 1991 Toyota Camry

1 Answer

Why does my blower only work on number 4


this sounds like a bad blower motor resistor that is bad and only working when the switch is put in the 4th position. the resistor has resistors wires in it that respond to the path of power through fan switch on the dash, depending on which fan speed you need.

Aug 22, 2014 | 2002 Ford Focus

1 Answer

The fan will not come on in the first 4 positions,


It may be the fan motor reostat. It's located under the dash on the passenger side on the duct work. It kinda works like a dimmer switch.

May 27, 2010 | 2001 Chevrolet Impala

1 Answer

Heater blower switch will only work at possion 4


Underneath the glove compartment on the passenger side is a cover which must come off,2 plastic screws holding this cover.Underneath you will find a 5 pin connector[big plug] connected to a white connector in the blower fan housing.This is called the fan resistor which controls the blower fan speed.Unclip the resistor out the housing and renew.Your problems should be solved..regards

Dec 21, 2009 | 2005 Volkswagen Golf

1 Answer

Fan switch does not work in the 1, 2, 3, position 2006 Cobalt


You have a problem with the blower motor resistor. This is a very commen problem on all gm cars and light trucks. The part is not to pricey. You can find the resistor under the glove box buy the blower motor. Two bolts and out it comes.

Sep 14, 2009 | 2006 Chevrolet Cobalt

1 Answer

Climate control switch does not work in lower modes only in high.


The pontiacs have an issue with the ignition switch, I have a 2001 grand prix that did the same. The ac fan would only work on 5 and the headlights would go off if on 1-4 replace the switch and all is fine.

Jun 02, 2009 | 2003 Pontiac Grand Prix

1 Answer

Fan switch position 3 and 4 do not work


More then likely the switch itself is bad. Chances are the contacts inside the switch are not connecting and allowing the motor to operate in those positions. If possible, try a known good switch in it's place.

Nov 29, 2008 | 2004 Oldsmobile Silhouette

2 Answers

Climate control fan


I had the same problem and after checking all the appropriate fuses was looking for the cost of a new switch and noticed another with the same problem and directed me to the 4-pin connector under the glove box. I noticed electrical tape coming loose and thought maybe the connector had been hit by a passengers foot, etc. I jiggled the connector and reseated it and tried the fan switch and it worked. I then taped the 4 pin connector up against the housing with electrical tape and it has been working fine ever since. Maybe the connectors do not mate properly or are too loose of engagement. Hope this helps....saved some $$$$......Can't believe electrical tape was used by GM in lieu of some other more attractive method.

Oct 11, 2008 | 2005 GMC Canyon

1 Answer

4 speed blower (fan)


You'll have to go to the dealer and buy a new switch panel. There is a circuit board behind the switch panel that went bad on yours. Don't get one from the wrecking yard, I made that mistake once.

Aug 11, 2008 | 1996 GMC Jimmy

Not finding what you are looking for?
2000 Nissan Altima Logo

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...