Question about 1987 Nissan Stanza

1 Answer

What size is the half shaft nut on the 1987 stanza

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

36mm

Posted on Nov 20, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the starter located on a 1988 nissan stanz


should be on the inner side of the engine between engine block and the gear box housing,above the right side drive shaft.It is below the inlet manifold.

Apr 22, 2014 | 1987 Nissan Stanza

2 Answers

How do i remove the fan and pulley on a 1987 ford ranger 2.9 v-6?


The question is: How remove clutch in order to remove fan mounted on its engine-side face.
  • Generally, the clutch drive half shaft must be uncoupled from coolant pump (impeller drive) half shaft using special wrench kit available as loaner from AutoZone (free with $79 approx deposit).
  • Best done after shroud & radiator remove after coolant drained.
  1. Uncouple coolant pump and fan clutch drive shaft(s) as follows:
    1. span across combo-pulley-sheaves-unit mounting bolt heads with large tool kit wrench, and
    2. span inline clutch coupling nut with small tool kit wrench. Then,
    3. turn small wrench (and coupling nut) CW while resisting with large wrench (CCW) to turn coupling nut until disengaged from coolant pump drive shaft.
  2. Remove fan/clutch assembly.
  3. Note direction of mounted fan hub and fan blades orientation to ensure proper re-assembly.
  4. On rear of clutch assy, remove 4 bolts to disengage and remove fan.
  5. Assemble new fan to clutch (or, preferably, new clutch and new fan) using new bolts and washers provided with fan.
  6. Couple fan-clutch assy to coolant pump drive shaft as per opposite of uncoupling step 1, above. (Turn inline nut CCW to tighten...30 ft-lb.
  7. Check that fan can be hand turned...CW.)
  8. Rest shroud over and onto fan.
  9. Replace radiator; remount shroud; reclamp hoses, and refill and air purge cooling system.
remove-fan-pulley-1987-ford-ranger-2-9-v-2cg35myhodwcq1awmwat24pw-4-0.jpg

Aug 12, 2012 | 1987 Ford Ranger

1 Answer

I am trying to replace the starter in my 86 nissan stanza but cant see it


NISSAN STANZA WAGON - Manual Transmission


Q. Where is the starter on a 1986 nissan stanza station wagon and how do you get to it ?


Due to limited access to the starter, it is recommended that the transaxle be removed when servicing the starter.

REMOVAL:

1. Cold vehicle.

Remove 2 mounting bracket bolts, 10 & 12 mm (Figure 1).

Remove top starter motor bolt 14 mm with universal & long extensions.

Raise vehicle on hoist.

Remove front splash pans 10 mm.

Automatic transmission: Drain 2 qts out.

Remove rt-ft wheel 21 mm., & tie rod (Figure 3), axle cap, cotter pin, adj-nut & rubber washer.

Remove ball joint nuts 17 mm., left lower control arm 19mm. & swaybar bracket 14 mm. (Fig 2).

Remove axle nut 36mm (Figure 4), the front tube, catalytic converter heat insulators 10mm, ctr ex-tube 17 mm., and front tube from exhaust system (Figure 5).

Remove long bolt from ft engine mount (next to radiator), 17mm socket (Figure 6, Item A).

Remove tension rod mount 14 mm. Has adj-bracket with rubber insulators (Fig 6, Items B, C).

Remove right side drive shaft bolts that hold shaft to bracket mounted on engine (Fig7) 12mm.

Remove rt-driveshaft.

CAUTION: Transaxle side seals are cut by spline teeth.

Install hoist type transmission jack and wooden block under the transmission/engine. Be certain the transmission is safely balanced on the hoist.

Remove 5 engine crossmember mounts (3 bolts, 2 nuts) 14mm.

Remove nut that attaches crossmember to engine mount.

Loosen stabilizer bar mounts to allow adequate clearance for crossmember to be removed.

Remove following brackets to allow starter assembly to pass through bottom:

tubular support bracket - engine to transaxle

angled support bracket - driveshaft bracket to engine mount

manifold collector stay - (bottom bolts)

Loosen top bolts, remove bracket above driveshaft-holding bracket 14mm.

NOTE: This bracket is slotted to allow it to slide out without completely removing the bolts.

Remove bottom starter motor mounting bolt.

Separate starter assembly from bellhousing, DC all cables/connectors, remove starter motor.

When installing starter, connect cable, install/torque starter bolts.

Nov 03, 2010 | 1986 Nissan Stanza

1 Answer

Cv shaft replace


This is usually the same on all front wheel drive cars..

Remove the wheel

Remove the brake caliper

Remove the brake rotor

Remove the spindle nut

Remove the wheel bearing assembly (usually 3 bolts)

-The next step may be optional, depends on the car-
Unbolt the lower ball joint (under the A-frame, some are riveted, if so, drill them out and chisel or just chisel them off with a metal chisel, sometimes you can cut the rivet heads off with a sawzall then pry it apart from the a-frame)

Pull the wheel bearing assembly from the spindle of the CV half shaft.
(Sometimes you need a wheel puller)

Once its loose, all you have to do it yank it out, and push the new one in. Make sure the new one pops in and is seated firmly.

Reverse steps for re-assembly. If you took the ball joint loose and it was riveted, use hardened steel bolts and nuts with lock washers to replace it, or buy a new ball joint, they aren't that expensive and it will come with bolts.

Good luck

May 09, 2010 | 1992 Nissan Stanza

1 Answer

Won't go in gear because of leakage


There should be a nut in the shaft to hold it in place.

May 16, 2009 | 1987 Dodge Dakota

1 Answer

1987 Toyota Celica ST half shaft


pull wheel, remove nut on half shaft, calaber, brakes, roader, tie rod, lower control arm, pop out half shaft from knuckle reinsert shaft to tranny and put back together easy looking about an half hour to an hour

Feb 23, 2009 | 1987 Toyota Celica

1 Answer

I need the number on the computer (ECU) nissan Stanza 87 SW, STD,FWD


Hi... On your question For ECM to 1987 Nissan Stanza..
Are 6 Available number .
2 are for vehicles 4WD. Incl. wagon. Calif emissions. 2261A-20R66RE,
with out calif, 2261A-20R06RE,

2 For vehicles FWD Wagons only. Calif emissions, 2261A-20R75RE,
With out Calif emissions, 2261A-20R15RE.

2 For vehicles Sedans FWD Exc Wagon. Calif emissions, 2261A-D5507RE,
With out calif emissions, 2261A-D4507RE,

NOTE , " RE" Mean Remanufactured ECM. Is not available new.

Ok.. Are the number I have Based on Mitchell ondemand, Repair Software.

I hope this info help on your question.
Any more questions let me know...


Nov 07, 2008 | 1987 Nissan Stanza

2 Answers

1987 Nissan Stanza


i had this problem too you have to reset something but i never found a good source as to what exactly

Jul 11, 2008 | 1987 Nissan Stanza

1 Answer

Gears


Could be the clutch is wearing down.If it's in ALL gears,it is likely the clutch.If i remember correctly,your car has a hydraulically activated clutch.If this is the case,under the dash,where the clutch pedal attaches to the clutch master cylinder,there is a jam nut,either 12mm or 14 mm wrench,loosen the jamnut,and spin the threded rod in,towards the clutch pedal,and away from the firewall.This should make your clutch pedal engagement point closer to the floor,and easier to shift.

Jul 08, 2008 | 1986 Nissan Stanza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...