Question about 1999 Dodge Ram

1 Answer

What is the specific name of the "yoke" that the rear of the driveshaft bolts to, on the differential?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 14,036 Answers

REAL NAME IS SLIP JOINT.MOST PEOPLE SLIP YOKE.

Posted on Oct 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you replace rear oil seal in 1994 Isuzu Standard tranmission


Chockblock front wheels to prevent truck rolling, and jack vehicle up and place a jackstand under frame to prevent vehicle falling. Remove driveshaft, seal is now visible to be pried out for new one to be lightly tapped into place with a rubber mallet or hammer, along with a wooden block, taking care to keep new seal straight while replacing. replace driveshaft and check fluid level, lower vehicle and remove chockblocks.

Feb 13, 2015 | 1994 Isuzu Pickup

1 Answer

How do I take off my drive shaft? When i accelerate, I hear a squeeking noise and i believe its my rear driveshaft. I need to take it off and bring it to a machine shop to get fixed but how do i take it...


There should be 4 bolts on the rear differential side of the driveshaft...remove these 4 bolts along with the c shaped saddles and put them aside where they won't get lost...the driveshaft will drop down..then all you need to do is pull the other end out of the transmission/transfer case. the transmission side has a splined shaft...don't worry about aligning it up when you get the d-shaft back from the ,mach shop..all you need to do to realign it is to jack up one side of the rear so the yoke on the differential will line up to the shaft ..make sure you block the wheels so the truck won't move. put everything back in reverse order as mentioned above...make sure the bolts on the rear saddles are tight(or else the driveshaft may come off)

Dec 22, 2010 | 1995 Chevrolet Blazer

1 Answer

How do you get the front driveshaft out of 2001 chevy 4X4


Remove transfer case shield. Remove clamp on boot
where front drive shaft meets transfer case. use a flat
screwdriver to pry free end up and release clamp. (you need a special clamp tool to reinstall clamp )
Remove 4 bolts at differential end that hold U joint Retainers to yoke. Slide drive shaft to rear enough to clear yoke. then let drive shaft drop so it clears differential and slide forward until it come off transfer case shaft.

Sep 12, 2010 | 2000 Chevrolet Silverado

1 Answer

How do i replace a driveshaft for a 1997 lincon cotanental


I searched under 1997 lincoln continental and found this: Driveshaft and U-Joints
REMOVAL & INSTALLATION Town Car and Mark VII-VIII Fig. 1: The bolts retaining the rear driveshaft yoke-to-differential flange require a 12mm, 12 point wrench or socket to loosen them 91197p12.jpg
Fig. 2: Remove the bolts retaining the rear driveshaft yoke-to-differential flange 91197p11.jpg
Fig. 3: Separate the driveshaft from the axle flange and . . . 91197p13.jpg
Fig. 4: . . . disengage the driveshaft from the transmission output shaft 91197p14.jpg
Fig. 5: Insert a plug onto the splines of the transmission output shaft to prevent fluid from leaking out 91197p15.jpg
  1. Raise and safely support the vehicle.
  2. Mark the position of the driveshaft yoke on the axle companion flange so they can be reassembled in the same way to maintain balance.
  3. Remove the flange bolts and disconnect the driveshaft from the axle companion flange.
  4. Allow the rear of the driveshaft to drop down slightly.
  5. Pull the driveshaft and slip yoke rearward until the yoke just clears the transmission extension housing seal. Mark the position of the slip yoke in relation to the transmission output shaft, then remove the driveshaft.
  6. Plug the transmission to prevent fluid leakage. To install:
  7. Lubricate the yoke splines with suitable grease.
  8. Remove the plug from the transmission and inspect the extension housing seal; replace if necessary.
  9. Align the slip yoke and output shaft with the marks made at removal and install the yoke into the transmission extension housing. Be careful not to bottom the slip yoke hard against the transmission seal.
  10. Rotate the axle flange, as necessary, to align the marks made during removal.
  11. Install the driveshaft yoke to the axle flange. Install the bolts and tighten to 71–95 ft. lbs. (95–130 Nm).
  12. Lower the vehicle.
prev.gif next.gif

Jul 05, 2010 | 1997 Lincoln Continental

1 Answer

2004 Explorer: Rear differential cover is leaking, how do I fix i...


put flat pan under the housing remove the bolts holding the cover usually 10 or 12 (1/2 or #12 metric) bolts? allow the rear end grease to drain... then scape off the old gasket clean with brake cleaner spray install either new gasket or form one with oil resistant silicone put the cover back on , dont refill the fliud for at least 12 hours if using silicone. Also check the front driveshaft rear end yoke seal....they sometimes leak making the illusion of a rear end pan cover leak...if that is leaking you remove the shaft carefully...remove the large yoke retaining nut, replace the press in seal...be sure retaining yoke nut is properly torqued when reinstalling .

May 06, 2010 | 2004 Ford Explorer

1 Answer

What needs to be done to remove the draft shaft on a 1968 CORVETTE with 327CCs?


Actually a relatively easy job as both the front and rear universal joints are held on with straps and bolts. Assuming the car is safely in the air and not going to roll away, first mark a line on the differential yoke and on the driveshaft so you can reinstall it in the same position. Repeat this procedure at the front end of the driveshaft at the transmission yoke.

Next remove the 4 bolts and 2 straps that hold the front universal joint into the transmission yoke, then you can lightly pry the universal toward the rear of the car and free it from the yoke. Have a prepared place to lower the front of the shaft on such a small piece of plywood or something to prevent it from being damaged. Also take care not to remove the yoke from the transmission to prevent fluid loss, even if you need to temporarily tie the yoke in place.

Next remove the 4 bolts and 2 straps that hold the rear universal joint into the differential yoke, then you can lightly pry the universal toward the front of the car and free it from the yoke.

Thats all! Good luck and totally enjoy one of the best cars ever built!

Nov 13, 2009 | 1965 Chevrolet Corvette

1 Answer

Rear differential on a 2004 Mustang gt leaking fluid


this is for 2003 7.5 inch ring gear axle. SECTION 205-02A: Rear Drive Axle/Differential — Ford 7.5-Inch Ring Gear 2003 Mustang Workshop Manual IN-VEHICLE REPAIR Drive Pinion Flange and Drive Pinion Seal Special Tool(s) s3b%7eus%7een%7efile=st2026a.gif%7egen%7eref.gif2-Jaw Puller 205-D072 (D97L-4221-A) or equivalent s3b%7eus%7een%7efile=st1257a.gif%7egen%7eref.gifHolding Fixture, Drive Pinion Flange 205-126 (T78P-4851-A) s3b%7eus%7een%7efile=st1862a.gif%7egen%7eref.gifInstaller, Drive Pinion Flange 205-002 (TOOL-4858-E) or equivalent Removal
  1. Raise and support the vehicle.
  1. Remove the rear wheel and tire assemblies.
  1. s3b%7eus%7een%7efile=ani_caut.gif%7egen%7eref.gif CAUTION: Remove the rear brake calipers to prevent drag during the drive pinion bearing preload adjustment. s3b%7eus%7een%7efile=ani_caut.gif%7egen%7eref.gif CAUTION: Do not allow the calipers to hang from the brake hoses. Remove the rear brake caliper and support bracket from the knuckle as an assembly. Wire the caliper and support bracket assembly out of the way.
  2. s3b%7eus%7een%7efile=ani_caut.gif%7egen%7eref.gif CAUTION: Index-mark the driveshaft flange and pinion flange (4851) to maintain initial balance during installation. s3b%7eus%7een%7efile=ani_caut.gif%7egen%7eref.gif CAUTION: The driveshaft centering socket yoke fits tightly on the pinion flange pilot. Never hammer on the driveshaft or any of its components to disconnect the yoke from the flange. Pry only in the area shown, with a suitable tool, to disconnect the yoke from the flange. Disconnect and position the driveshaft out of the way.
  1. Install an Nm (inch/pound) torque wrench on the nut and record the torque necessary to maintain rotation of the drive pinion gear through several revolutions.
  1. s3b%7eus%7een%7efile=ani_caut.gif%7egen%7eref.gif CAUTION: After removing the nut, discard it. Use a new nut for installation. Use the special tool to hold the pinion flange while removing the nut.
  1. Index-mark the pinion flange and drive pinion gear stem to maintain initial balance during installation.
  1. Using the special tool, remove the pinion flange.
Installation
  1. Inspect the pinion flange seal journal for rust, nicks, and scratches prior to installing the flange. Polish the seal journal with fine crocus cloth, if necessary.
  1. Lubricate the pinion flange splines.
    • Use SAE 80W-90 Premium Rear Axle Lubricant XY-80W90-QL or equivalent meeting Ford specification WSP-M2C197-A.
  1. NOTE: Disregard the index marks if installing a new pinion flange. Position the pinion flange.
  1. Using the special tools, install the pinion flange.
  1. s3b%7eus%7een%7efile=ani_caut.gif%7egen%7eref.gif CAUTION: Do not under any circumstance loosen the nut to reduce preload. If it is necessary to reduce preload, install a new collapsible spacer (4662) and nut. s3b%7eus%7een%7efile=ani_caut.gif%7egen%7eref.gif CAUTION: Remove the special tool while taking preload readings with the Nm (inch/pound) torque wrench. Tighten the nut to set the preload.
    • Rotate the drive pinion occasionally to make sure the differential pinion bearings (4630) (4621) seat correctly. Take frequent differential pinion bearing torque preload readings by rotating the drive pinion with a Nm (inch/pound) torque wrench.
    • If the preload recorded prior to disassembly is lower than the specification for used bearings, then tighten the nut to specification. If the preload recorded prior to disassembly is higher than the specification for used bearings, then tighten the nut to the original reading as recorded.
    • Refer to the torque specification for used differential pinion bearings in the Specifications portion of this section.
  1. s3b%7eus%7een%7efile=ani_caut.gif%7egen%7eref.gif CAUTION: Align the index marks. s3b%7eus%7een%7efile=ani_caut.gif%7egen%7eref.gif CAUTION: Install the driveshaft with new bolts. If new bolts are not available, apply Threadlock and Sealer EOAZ-19554-AA or equivalent meeting Ford specification WSK-M2G351-A5 to the threads of the original bolts. s3b%7eus%7een%7efile=ani_caut.gif%7egen%7eref.gif CAUTION: The driveshaft centering socket yoke fits tightly on the pinion flange pilot. To make sure that the yoke seats squarely on the flange, tighten the bolts evenly in a cross pattern as shown. Connect the driveshaft. .
  1. Install the rear brake calipers.
  1. Install the rear wheel and tire assemblies.
  1. Lower the vehicle.

May 26, 2009 | 2004 Ford Mustang

2 Answers

Part names


cardan centering bearing
point bolts needed to be removed that connects D.S.to transfercase

May 22, 2009 | 2001 Ford Excursion

1 Answer

Rear differential driveshaft seal leak.


Hello,you need to remove driveshaft to be able to get to the nut.Remove the nut (MAY BE VERY TIGHT) and pull the yoke or flange as you called it out & you can pop old seal out & new seal in.You may want to smear a tiny bit of grease or vasoline on outside of seal for easier installation & also on the rubber part of seal so itwon't get damaged when you re-install the yoke.Hope this helps.

Dec 29, 2008 | 1988 Isuzu Trooper 2 Door

4 Answers

Driveshaft yoke balancer


I had the same problem and removed the balancer from the drive shaft this morning. I put the drive shaft back on, and drove the truck around all day, highway, city, stop and go, there were no problems, and the noise was gone, and I had no vibrations at all. So you should be fine if you remove the balancer.

Jun 11, 2008 | 2003 Ford Ranger Regular Cab

Not finding what you are looking for?
1999 Dodge Ram Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...