Question about 1988 Jeep Cherokee

1 Answer

WHAT IS CYLINDER HEAD BOLT TORQUE ON A 1988 JEEP CHEROKEE LTD. 4.0?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Jeep Master
  • 76,164 Answers

Torque settings are 110 ft LBS for nine of the ten bolts one bolt is 100 ft LBS /#1 Tighten all bolts in sequence 1 to 10 at 22 ft LBS #2 tighten all bolts 1 to 10 at 45 ft LBS #3 tighten all bolts 1 to 6 at 110 ft LBS #4 bolt #7 at 100 ft LBS #5 BOLT 8 TO 10 AT 110 FT LBS . HEAD TIGHTEN SEQUENCE - standing at front of car bolts down left side are 8/4/1/5/9 bolts down right side are 7/3/2/6/10. left side meaning distributor side.

Posted on Oct 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I want torque setting for jeep 3.7l on cylinder head


Hi there:
Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
  1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
  2. Step 2: Bolts 1-10 verify torque without loosening
  3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
  4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
  5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


12_24_2012_2_41_06_pm.gif


Hope this helps.

Dec 24, 2012 | Jeep Cars & Trucks

1 Answer

I am looking for the head bolt torque specifications and sequence for a 1988 jeep Cherokee 4.0 i6


zjlimited_950.jpg

Fig. 17: Cylinder head bolt torque sequence (click over pic for zoom)


Apply sealing compound only to the cylinder head gasket. Do not allow sealing compound to enter the cylinder bore.

Install the cylinder head and bolts. The threads of bolt No. 11 must be coated with Loctite® 592 sealant before installation. Tighten the bolts in 3 steps, using the correct sequence:

Tighten all bolts to 22 ft. lbs. (30 Nm).
Tighten all bolts to 45 ft. lbs. (61 Nm).
Retighten all bolts to 45 ft. lbs. (61 Nm).
Tighten bolts 1 through 10 in sequence to 110 ft. lbs. (150 Nm).
Tighten bolt 11 to 100 ft. lbs. (136 Nm)
Tighten bolts 12 through 14 to 110 ft. lbs. (150 Nm)




Hope this helps (remember to rate and comment this answer).

Mar 30, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

Can you tell me the torque spec.on head bolts for a 1985 ltd 3.8 thank you


Six IN LINE - 6L

zjlimited_510.jpg

Fig.: Cylinder head torque sequence - 6 -cylinder engine



Cylinder head torquing should proceed in three steps and in the prescribed order. Tighten them first to 50-55 ft. lbs. (65-71 Nm), then give them a second tightening to 60-65 ft. lbs. (78-84 Nm). The final step is to 70-75 ft. lbs. (91-97 Nm), at which they should remain undisturbed.


Six IN V - 6V

zjlimited_511.jpg

Fig.: Cylinder head bolt torque sequence - 6 -cylinder engine

Tighten the head, according to the illustrated sequence in three progressive steps. Tighten the bolts to 50-55 ft. lbs. (68-74 Nm), then 60-65 ft. lbs. (81-88 Nm) and finally to 75 ft. lbs. (102 Nm).


Hope this helps (remember to rate and commene this answer).

Jan 19, 2011 | 1985 Ford LTD

1 Answer

What is the cylinder head torque on a 2001 jeep cherokee


Please don't forget to rate....thanks:


e1aba13.gif

  1. Tighten the engine cylinder head bolts in sequence according to the following procedure

    CAUTION During the final tightening sequence, bolt No.11 will be tightened to a lower torque than the rest of the bolts. DO NOT over tighten bolt No.11.

  2. Tighten all bolts in sequence (1 through 14) to 22 ft. lbs. (30 Nm).
  3. Tighten all bolts in sequence (1 through 14) to 45 ft. lbs. (61 Nm).
  4. Check all bolts to verify they are set to 45 ft. lbs. (61 Nm).
  5. Tighten bolts in sequence:
  6. Bolts 1 through 10 to 110 ft. lbs. (149 Nm).
  7. Bolt 11 to 100 ft. lbs. (135 Nm).
  8. Bolts 12 through 14 to 110 ft. lbs. (149 Nm).
  9. Check all bolts in sequence to verify the correct torque.

Mar 06, 2010 | 2001 Jeep Cherokee

2 Answers

What is the torque specs for a 1998 jeep Cherokee classic straight 6 4.0 liter? I am replacing the head gasket and need to find the lbs of torque. Thank you for any advice, pictures, etc.


Torque sequence ------------------ front | 12 8 4 1 5 9 13 | of | | engine | 11 7 3 2 6 10 14 | ------------------ Final torque must be reached in 3 equal steps Step 1: torque all bolts (except bolt 11) to 110 Ft/Lbs Step 2: torque bolt 11 to 100 Ft/Lbs Recheck final torque in sequence.

  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Disconnect the hoses at the thermostat housing.
  4. Properly relieve the fuel system pressure.
  5. Remove the cylinder head cover.
  6. Loosen the rocker arms.
  7. Remove the pushrods.

The valvetrain components must be replaced in their original positions.
  1. Remove the intake and exhaust manifold from the cylinder head.
  2. Disconnect the spark plug wires and remove the spark plugs.
  3. Disconnect the temperature sending unit wire, ignition coil and bracket assembly from the engine.
  4. Remove the accessory drive belt(s).
  5. Unbolt and set aside the power steering pump and bracket. Do not disconnect the hoses.
  6. Remove the intake and exhaust manifold assembly.
  7. If equipped with A/C, perform the following:
    1. Remove the compressor and position it aside with the lines attached.
    2. Remove the compressor bracket bolts from the cylinder head.
    3. Loosen the through bolt at the bottom of the bracket.

  8. Remove the alternator.
  9. Remove the cylinder head bolts, the cylinder head and gasket from the block.

Bolt No. 14 cannot be removed until the head is moved forward. Pull the bolt out as far as it will go and suspend in place by wrapping with tape.
  1. Discard the gasket. Thoroughly clean the head-to-block mating surface.
  2. Clean and inspect the cylinder head thoroughly. Refer to the engine reconditioning portion outlined later in this section.

To install:
  1. Coat a new head gasket with suitable sealing compound and place it on the block. Most replacement gaskets will have the word TOP stamped on them.

Apply sealing compound only to the cylinder head gasket. Do not allow sealing compound to enter the cylinder bore.

Oct 08, 2009 | 1998 Jeep Cherokee

2 Answers

What is the tension on cylinder head bolts for a jeep grand cherokee 307935 4 litre, 6 cylinder, 1999, petrol motor.


Coat threads of left hand front bolt with sealant: 1st - step; - 22 ft./lbs. 2nd - step; - 45 ft./lbs. 3rd - step, all bolts except L.H. front bolt; - 110 ft./lbs. 4th - step, L.H. front bolt; - 100 ft./lbs. fig100.png

Sep 05, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Head Bolt Torque for a 2000 Grand Cherokee Laredo 4.0L


the torque is a 4 step process

1 torque all bolts to 22 ft/lbs
2 torque all bolts to 45 ft/lbs
3 recheck all bolts to 45 ft/lbs
4 torque bolts 1 thru 10 to 110 ft/lbs
bolt 11 to 100 ft/lbs
bolts 12 thru 14 to 110 ft/lbs
bolt #1 is the fourth bolt from the front on the passenger side....#2 is the fourth bolt on the drivers side then you continue in a clockwise order

Jan 04, 2009 | 2004 Jeep Grand Cherokee

1 Answer

What to torque head bolts on in 04 jeep grand cherokee 4.0 6cyl.


the 4th bolt back from the front on pasenger side is the #1 head bolt, tighten in a clockwise rotation. it is a 4 step process.torque all bolts to 22 ft lbs...step 2 torque all to 45 ft lbs...step 3 retorque all to 45 ft lbs...4th step torque bolts 1 through 10 to 110 ft lbs... bolt 11 to 100ft lbs then bolts 12 thru 14 at 110 ft lbs

Dec 25, 2008 | 2004 Jeep Grand Cherokee

1 Answer

Torque specs


Head bolt torque is 65 ft lbs, use the below sequence, go over bolts 3x to reach final torque (not all at once to 65)

13 5 2 10
front of engine 17 9 1 6 14
16 12 8 4 3 7 11 15
good luck!

Oct 25, 2008 | 1988 Chevrolet K1500

1 Answer

1991 jeep cherokee sport 4.0


 For your 1991 Jeep Cherokee 2WD 4.0L MFI :
  Foot pounds (Final torque) 

  Note:
  Torque sequence ------------------  
  front    | 12  8   4   1   5   9  13 | 
  of | | 
  engine | 11  7   3   2   6   10 14 | 
  ------------------  
Final torque must be reached in 3 equal steps  
  Step 1: torque all bolts (except bolt 11)  
  to 110 Ft/Lbs  
  Step 2: torque bolt 11 to 100 Ft/Lbs  
Recheck final torque in sequence  

Sep 30, 2008 | 1991 Jeep Cherokee Briarwood

Not finding what you are looking for?
Cars & Trucks Logo

320 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...