Question about 1984 Ford F 350

Open Question

1984 ford F350 diesel...Turn signals stopped working...don't know which fuse...but replaced them all and new flasher. Brake lights work and flasher works...but no turn...replaced brake light switch earlier and then turn signals stopped working...

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 508 Answers

SOURCE: Rear turn signals and brake lights won't work

Probably the turn signal switch assembly. This is a common problem with the older Fords. The switch is a self contained unit at a cost of about $100.00.

Posted on Feb 09, 2009

  • 132 Answers

SOURCE: brake and turn signal lights stopped working on my 1996 Ford E150

You might have cut a wire or it could have broken or disconnected. Try tracing the wiring where you hooked up the trailer you may find one broken or disconnected.

Posted on Mar 26, 2009

  • 1 Answer

SOURCE: 1969 ford mustang mach 1 brake / stop light switch challenge

I installed a new turn signal switch in the steering column, and it fixed my brake light problem. Evidentally the turn signal and brake light wires use the same plug wires. It cost about $70. I would suggest doing this.

Posted on Mar 31, 2009

  • 10865 Answers

SOURCE: Brake light, reverse light and turn signal issues

Hello. The symptoms you are describing are likely due to a poor ground. Temporarily install a new ground wire by securing a piece of copper wire to the frame with a self tapping screw. Use this ground wire along with the hot wire to see if each of these lights works. If it does, trace the ground wire back to the frame, unscrew it and clean up the metal with emery cloth so you reestablish a good ground.

Posted on Jan 28, 2010

roniecon
  • 6826 Answers

SOURCE: 1986 ford f350 diesel no power to anything except

Check for a burned out fusible link,it will be on the solenoid switch,on the battery cable side.They look like wires,but if you pull on them,and they are burned out,they will pull apart like taffy.

Posted on Apr 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why aren't hazard lights or brake lights working?


Brake lights /rear hazard lights not working - Ford Truck ...

www.ford-trucks.com > ... > 1967 - 1972 F-100 & Larger F-Series Trucks
Jul 9, 2010 - After checking the brake lights I tried the emergency flashers and found that they are working in the front but not in the back. I do have rear turn ... 1995 F350 Brake Lights / Turn Signals not working
Jul 9, 2012
Turn Signals and Brake Lights Do Not Work
Mar 10, 2012
Turn Signal, Brake Lights, & Rear Hazard not working
Aug 3, 2010
Rear Turn Signals, Hazards and Brake Lights not working....
Aug 29, 200

Sep 30, 2015 | Cars & Trucks

1 Answer

2003 Ford F350 Super Duty 4WD Diesel 6.0L Duallie Turn Signals inop


you have a short in the wire somewhere. you can trace the wires and look for any exposed or burnt looking wires to start out with.

Dec 31, 2013 | Cars & Trucks

1 Answer

Where is the turn signal relay for 2002 f350 2wd diesel at


HI there:


On 2002 Ford Truck F350 Super Duty P/U 4WD 7.3L Turbo Diesel 8cyl the Flasher is located: front seating area, driver side, under dash, mounted in fuse panel.


Hope helps.

Mar 17, 2012 | Cars & Trucks

1 Answer

1995 Ford f250 brake lights don't work ad neither do the hazard flashers. I replaced the flasher node and the turn signals began to work but still no brake lights.


You may have a bad signal switch..Your brake lights run through the signal switch..Try hitting the brakes and move the switch around and see if your brake lights come on intermittently..

Sep 22, 2011 | 1995 Ford F250

1 Answer

I have a 98 eclipse. I was putting new tail lights on and then the signals stopped working along with the brake lights. the fuse to the brake lights had burnt so I replaced it. The signals however are...


IF THE TURN SIGNALS STILL WORK IN THE FRONT, THAT MEANS THE FUSE & THE FLASHER ARE OK. IF THE SIGNALS DON'T WORK AT ALL CHECK TURN SIGNAL FUSE & STOP / BRAKE FUSE. ARE YOU SURE THE CORRECT BULBS ARE BEING USED?

Jan 24, 2011 | 1998 Mitsubishi Eclipse

1 Answer

I have no turn signals. The 4 ways work running lights work and brake lights work but not the turn signals


Check the flasher that is located under the dash, sometimes there on the fuse box.

Dec 21, 2010 | 1990 Ford F350

1 Answer

2004 f350 4x4 6.0 diesel electrical problems


Locate the fuse box under the dash panel. Pull the fuses one at a time and inspect. They are very hard to judge if the fuse(s) are blown unless you pull them out to inspect.

Dec 08, 2009 | 2002 Ford Explorer

2 Answers

What causes both brake and flashers to stop working?


Many cars have the same fuse for turn signal and brake lights. Check that fuse for a start.

Aug 11, 2008 | Ford E-150 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...