Question about 2000 Chevrolet Metro

Open Question

I have a 2000 chevy metro that the driver side door is locked closed, key turns lock but neither handle will open door

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: driver's door lock will not open by key or electronic fob

I was able to determine if you move the inside door handle toward the front of the car, then you could remove the door panel. However, it takes a little force to pot out the plastic clips, but if you work around the outside by appling pressure with a thin tool, such as a putty knife it will pot out.

My problem was a small yellow plastic part that connects the outside and inside door handle rods was broken.

So I plan to replace the part and see if that fixes the provlem. If so I can save over $340 dealer repair costs.

Posted on Nov 13, 2008

  • 22 Answers

SOURCE: Driver side door lock seems mechanically "stuck"

The panel pops off. There are cheap tools to help with this at your local AutoZone. You may be able to just pull them off, you will need new clips which are just a couple of dollars or else your panels will be loose when you put them on. There maybe a screw or 2 that will be hiding and you will find them as your taking the panel off, start at the bottom. As for your original problem I would say the linkage is binding up some where and needs a bit of grease. Hope this helps. Richard

Posted on Mar 09, 2009

  • 1 Answer

SOURCE: 2000 chevy astro van electronic door lock problem

Try to replace fuse #13

Posted on May 22, 2009

motorhead427
  • 24 Answers

SOURCE: Chevy Impala Door lock issue

Which is it, 98 Eclipse, or 06 Impala? Either way, your door lock actuator is stuck in the locked position either electrically or mechaically. The way to check this is to remove the door panel and unplug the actuator. If door lock can now be moved then you have an electrical problem (faulty door lock switch or faulty door lock module). If you still cannot unlock door then actuator is mechanically bad and must be replace (usually the case)

Posted on May 30, 2009

  • 10986 Answers

SOURCE: 2007 chevy tahoe driver side door handle will not open door

the linkage behind the handle either the retaining clip broke or popped off need to remove the door panel to check and fix

Posted on Mar 13, 2010

Testimonial: "Thanks I thought it might be a cable or linkage. Much thanks"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mazda 6 2005 driver door jammed


if you talking about door latch wont let door close.try to reset all door locks.first if you cant get door close.work unlock button with remote or door switch.then hold open door handle while you flat screw driver pull up latch in door latch should stay up so door will close.once get door close.try resetting all door locks by sitting inside vechicle with all doors close.remove key from ignition.open drivers door.wait 24 seconds.turn ignition switch on and back to lock position 3 times.press and release drivers door courtesy light 3 times.ensure doors lock and unlock.if not wait 40 seconds and repeat procedure.if this procedure fails. you have problem in the door latch and lock mechanism inside the door itself.

Jan 04, 2013 | 2004 Mazda 6 Sport

1 Answer

2000 cadillac deville driver side won't open with the key


1) Key turns but dose not unlock door. This means that the rod that goes to the back of the lock has came off. This also means that is the reason door is not unlocking with the remote as it pops the lock rod inside the door which pushes the lock open.
2) Key does not turn lock at all but works passengers side door. This means that the locks has been changed in the door, but that doesn't sound like the problem as you say the remote doesn't open the drivers side door so more than likely the rod has came off the back of the lock

Nov 07, 2012 | Cars & Trucks

1 Answer

Key buttons will not operate locking system,i have changed battery but still no good.use master key,gets me into the car but alarm goes off and also when i attempt to drive it.


I have the same problem kinda. Lost my master key and sent my ecu off with a home made 2 button key to program immobiliser. This key works to start the engin and drive but I cannot get the key to program with the alarm and locking system. You can try the following steps as may work for you.

I can get my car into programming mode after step 1 but step 2 does not work for me. The locks do not go off at all, not once or twice. Battery in remote key is fine as LCD lights red.

Can anyone help please?

Toyota celica 2000 - 2005 remote keyless entry programming guide
STEP 1
1. Key out of the ignition. Open the drivers door , all other doors are closed . Driver door is unlocked

2. Perform these steps within 5 seconds
a. Insert the key into the ignition ( do not turn it ) take key out
b. Insert the key into the ignition ( do not turn it ) take key out

3. Perform these steps within 40 seconds
a. Close and then open the drivers door.
b. Close and then open the drivers door.
c. Insert the key into the ignition ( do not turn it ) and pull it out.

4. Perform these steps within 40 seconds
a. Close and then open the drivers door.
b. Close and then open the drivers door.
c. Close drivers door.
d. Insert the key into the ignition and leave it in the ignition.
Turn the ignition to on (as far as you can go without turning the engine over ), then back to off .
e. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.

STEP 2 (Does not work for me)

6. Perform these steps within 40 seconds
a. Press the lock and unlock buttons on the transmitter simultaneously for 2 seconds
b. Immediately after letting go of the lock and unlock buttons, press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock then unlock once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b as the remote was not accepted.

7. Open drivers door

Hope this works for you.
Hayley

Oct 03, 2010 | 2000 Toyota Celica

1 Answer

1998 4x4 ford explore driver side door will not


There are long linkage rods from the inside handle to the latch assembly. There should be an adjustment on these links. Too tight keeps latch from locking, too loose it won't unlatch. Use a screw driver or rod to trip the latch asm so you don't have to keep opening and closing the door. Also if it sticks closed and won't unlatch, the door won't be locked closed on you.

Feb 05, 2010 | 1998 Ford Explorer

1 Answer

Door Lock?


this is not a problem, it is a feature. its purpose is to try and make it harder to lock your keys in your car. try this: with the door open, pull the inner door handle like you are opening the door. with the handle pulled, lock the door. it will lock.

Nov 30, 2009 | Cars & Trucks

1 Answer

2000 chevy cavalier door wont close. door latch must be jammed. solutions?


you have to open the jaws on the lock by takeing a screw driver and pring it open while opening the handle. try that see if it works

Jul 27, 2009 | 2000 Chevrolet Cavalier

2 Answers

My door handle wont open my door on the drivers side. I have to roll down my window to open the door from the outside latch. Is it repairable, or do I have to replace any parts?


I have shaved door handles on a 2000 chevy silverado and the drivers side door just recently stopped opening it seems like its completely locked out and the door is closed so i cannot get to the bolts of the latch assembly when i hit the unlock button it unlocks half way and when you go to open the door it relocks itself even if you manually try to unlock the door and hold the lock forward it still wont open

Jul 12, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

2000 Toyota Sienna Minivan car alarm goes off.


1. Start with key out of the ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into ignition (Do not turn) and pull it out.
3. Perform these steps within 40 seconds.
A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting
with lock. Use an even pace and try to go about one cycle per second.
(1 cycle = 1 lock and 1 unlock.)
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting
with lock. Use an even pace and try to go about one cycle per second.
(1 cycle = 1 lock and 1 unlock.)
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Turn the ignition to ON (Do NOT Start) then back to OFF.
E. Remove the key from the ignition.

5. Within 3 seconds the power door locks should cycle automatically indicating successful entry
into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1 second.
B. Immediately after letting go of the lock and unlock buttons,
Press the lock button by itself and hold for 2 seconds. Within 3 seconds the door locks
should cycle once indicating successful programming. If the door locks don't cycle or
cycle twice, repeat steps A and B, your remote has not been accepted.
C. Repeat steps A and B in step 6 for each new transmitter.

7. Close drivers door.

Apr 25, 2009 | Chevrolet Malibu Cars & Trucks

2 Answers

Door Lock doesn't unlock from outside


linkage is disconnected. most pannels pop off easy to allow acess. then pull the cover away from the position close to key point and see if linkage is loose.

Mar 11, 2009 | 2000 Plymouth Neon

Not finding what you are looking for?
2000 Chevrolet Metro Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...