Question about 2009 Toyota Camry

1 Answer

On my 2009 Camry 4 cylinder automatic, the tire pressure light came on recently and stays on, no blinking. The manual shows a reset switch on the side of the dash next to the glove box, but there is no button there or anywhere around there. The tire air pressure is good all around and the spare is full. Can you tell me anything regarding what to do short of bringing it to a mechanic? Thank you.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 3,239 Answers

I found this picture in database, did you look in glove box? I have a tech manual for tpms, for Toyota it just says lower dash for reset switch. For the picture, there is no orientation, you can't really tell anything. The info does say all Toyota with tpms has reset button. Sorry, I'm not sure where it is located or if there is one? I can only go by what the database says.
On my 2009 Camry 4 - reset-q51img3dbaqi2r4csl3ynbhn-1-0.jpg

Posted on Aug 10, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1779 Answers

SOURCE: spare tire key 2002 super duty

Is it a factory installed lock? If it is you might be able to get one at a ford dealer. They can cut a key for door and ignition if you give them the truck's vin (you have to show proof of ownership, registration, title) I don't know if they can use the vin for the spare tire key, but if they can't, drive to a good locksmith, they should be able to make one up w/ the truck @ their store. countrycurt0

Posted on Aug 23, 2008

zolo6321
  • 7 Answers

SOURCE: releasing the spare tire

if you look when you open the trunk right in the middle of the trunk there is a hole which your crank goes in to release the tire that is mounted under it, turn it either left or right to loosen

Posted on Dec 31, 2008

  • 189 Answers

SOURCE: Wrench for hydraulic jack and spare tire

junk yard or dealership.

Posted on Apr 23, 2010

  • 294 Answers

SOURCE: I cannot locate any reset

this is newly vehicle, but other models do not have a reset button is an auto reset after you star driving, if your tire press drops below 30psi it will turn lite on, so make sure your tires are inflated at 40psi also check spare tire it may have a 4 or 5 sensor system, no look......a bad sensor may be the cost, have a tire been fix lately? take it back they broke a sensor.

Posted on Oct 02, 2010

  • 4044 Answers

SOURCE: i checked the tire pressure

Each of these has an individual sensor. If you have replaced the rims with something other than the factory rims you will have this problem. If one of those sensors has gone bad you will have this problem as well. If you haven't replaced the rims than have the sensors checked. If you have there isn't much you can do except disable the light.

Posted on Oct 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tyre Pressure and ABS


By operating the tire pressure warning system reset switch, tire pressure warning system ECU can be set to issue a warning at an inflation pressure that corresponds with the type of tires.
Operate the tire pressure warning system reset switch only after the inflation pressures of all 4 tires have been adjusted on the vehicle.
To initialize the system, press and hold the tire pressure warning system reset switch for 3 seconds or longer with the power switch turned IG-ON. When starting the initialization, the tire pressure warning light blinks 3 times at 0.5 Hz.
During the initialization, the tire pressure warning system valve & transmitter measures the inflation
pressure of the tires, and registers the signals that are transmitted into the ECU at a frequency of 1 per
minute. The initialization process is completed when the signals from the tires have been received.
Once the tire pressure warning system reset switch has been pressed, do not turn the Ignition switch OFF for a few minutes.

Mar 05, 2014 | 2002 Toyota Corolla

1 Answer

Tyre pressure warning light showing when pressures are correct


Hi, the tire pressure monitor detects any changes in the tire inflation pressure. Therefore, it must initialize and store it in its memory if the tires or wheels have been replaced, re-inflated or the tires have been rotated. You can re-initialize the system by following these steps:

1. Check and make sure that your tires are inflated to the correct pressure

2. Turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (in the glove box) until the warning light turns off and then release the switch.

3. Now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

4. Initialization is *not* completed until driving at the vehicle speed of 19 mph or over for more than one hour. the tire pressure monitoring starts when initialization is completed.

May 13, 2011 | Renault 18I Cars & Trucks

2 Answers

How do i reset the tire pressure warning light on my 2009 matrix?


You can try disconnecting the battery for 30 sec. should reset

Feb 13, 2011 | 2009 Toyota Matrix

2 Answers

Had 4 new tires installed system blinked for 2 days on and off. now ligth stays on. how do you reset the light? all tires are at 35 psi.


It is possible that one of the sensors was damaged when they replaced the tires. If this occurred, the light will remain lit. Otherwise, after a pressure change the light will automatically turnoff after driving several minutes above 25MPH.

There is also a Nissan TPM reset tool which is designed to turn off the TPM warning light in 2003 and newer Nissan vehicles that have the TPM reset connector. Check your owner's manual to see if your vehicle has the connector. You can find the reset tool online for about $25.

Dec 11, 2009 | 2008 Nissan Frontier

1 Answer

How do you reset low tire light


1. check and make sure that your tires are inflated to the correct pressure

2. turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns off and then release the switch.

3. now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

4. initialization is *not* completed until driving at the vehicle speed of 19 mph or over for more than one hour. the tire pressure monitoring starts when initialization is completed.

Aug 20, 2009 | 2005 Chrysler PT Cruiser

3 Answers

The check tire pressure light and ABS auto traction sensor light keep coming on. Tire pressure is good


The tire pressure monitor detects any changes in the tire inflation pressure. Therefore, it must initialize and store it in its memory if the tires or wheels have been replaced, re-inflated or the tires have been rotated. You should be able to re-initialize the system by following these steps:

1. check and make sure that your tires are inflated to the correct pressure

2. turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns off and then release the switch.

3. now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

4. initialization is *not* completed until driving at the vehicle speed of 19 mph or over for more than one hour. the tire pressure monitoring starts when initialization is completed.

Aug 11, 2009 | 2004 Cadillac Deville

2 Answers

Maintenence required light and tire pressure lights will not go off after oil change and tire rotation on my Toyota Highlander. How do I turn them off?


The maintenance light needs to be reset manually. See my Tips and Tricks on this website for additional information on how to reset it.

You should also check your spare tire for proper inflation. It will set the tire pressure light, as the spare is monitored also. If all 5 tires are OK, you may have a malfunctioning tire pressure sensor. If the tires have been changed recently, people with older tire machines have been known to break the sensors regularly, by mistake.

Aug 10, 2009 | 2009 Toyota Highlander

3 Answers

How to reset tire pressure light on 2000 pontiac bonneville? I dont have owners manual.


to reset the tire pressure light.. the light will blink tire pressure.. well what you do is heck your tires make sure they are all to pressure of tire . then hold in on the tire pressure button for the count of 4 to 5 sec. and it will reset its selfs.

Jul 05, 2009 | 2000 Pontiac Bonneville

Not finding what you are looking for?
2009 Toyota Camry Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...