Question about 2001 Nissan Altima

Open Question

Need torque specs for transmission oil pan 2001 nissan altima

Posted by on

  • Anonymous Oct 09, 2010

    Nobody uses a torque wrench on a trans pan
    Do you own a Newton Meter Torque Wrench?

×

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6982 Answers

SOURCE: Need torque specs for oil pan gasket

There likely is a spec for oil pan but unless you are a finatic, you really don't need to know what it is. Simple rule: Don't crank down ******* any fastener. If corners near crank ends have larger fasteners, you can tighten them a bit more than on siderails. Before tightening anything, install all bolts finger tight, to ensure that they are not cross threaded. To avoid warping pan, tighten from the center of the pan, working towards both ends, alternating from side to side as you go. When you are finished, go over it again, using the same amount of force on each bolt. As I said, end bolts can if larger in diameter, be tightened more but be careful not to tighten so much that you will either split or push the gasket out the sides.. Anywhere two gasket ends **** together, I recommend using a sensor -safe dab of silicone. An oil pan is not under any mechanical stress or pressure. I have used this method for many years and NEVER had one leak. If you really need #s, small fasteners get about 12-15in lbs, larger ones about 20.

Posted on Dec 31, 2008

  • 1 Answer

SOURCE: 2001 Nissan Altima Transmission Oil pan

Dealer is the best option...i just had to replace mine and it was about 40.00

Posted on Dec 13, 2008

  • 158 Answers

SOURCE: 2000 sebring transmission pan torque spec

10 ft lbs no real patterm needed

Posted on Apr 03, 2009

  • 743 Answers

SOURCE: oil and transmission pan bolt torque specs

124 inch lbs on oil pan...Transmission pan 13 ft lbs.

Posted on Oct 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace the transmission fluid of 2009 nissan altima


two ways to do it
1-- drop the pan and drain half the oil and check / clean the filter
2---take it to an accredited auto transmission shop and have it changed with the engine running--- changes all the oil including what is in the torque converter with no need to drop the pan
method 2 is more expansive as you have to use more oil but the result is better as it removes any contaminants from the torque converter that method 1 does not do

Dec 24, 2016 | 2009 Nissan Altima

2 Answers

Two codes coming up on car even after fixing alot on car now need to figure out low cost ways to fix P0744 & P0722 code issues spent 1,800 on car & have spent 1,400 already in parts & labor.


you need a better mechanic that traces ALL of the possibilities of each code, not just read the code and trow in a part hoping that it's fixed ~ it can be wiring as well, not just plug in a new part as mentioned on the 2nd trouble code to the vehicle speed sensor

P0744 Torque Converter Clutch Circuit Intermittent


P0722 Output Speed Sensor No Signal

the first of the 2 looks to be more intensive to trace and find out the problem & the 0722 is the easier job for an intermediate mechanic to trace the wiring for continuity

Apr 20, 2015 | Cars & Trucks

2 Answers

Torque specs,rod bearings,2003 nissan altima 2.5


I need the torque specs for the connecting rod and main be

Sep 10, 2011 | Nissan Altima Cars & Trucks

2 Answers

I need the Torque Specs for a Nissan Q-R 2.5 Engine?


Nissan QR 2.5 engine produces a torque of 180 ft·lbf (244 N·m) of torque at 4000 rpm .

Oct 11, 2009 | 2003 Nissan Sentra

1 Answer

What are the torque specs for transmission pan bolts on 2003 maxima


hello! the torque specs on transmission oil pan are 62 to 80 inch pounds or 7 to 9 newton meters. hope this information helps you!

Sep 17, 2009 | 2003 Nissan Maxima

2 Answers

Replacing the oil pan on a 2000 altima


No You Just Want Them To Be Even And Not Over Tightened.
Happy Fixing.

Jan 15, 2009 | 2001 Nissan Altima

Not finding what you are looking for?
2001 Nissan Altima Logo

Related Topics:

361 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...