Question about 2006 Pontiac Torrent

1 Answer

Tool and oil pan light on - 2006 Pontiac Torrent

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Pontiac Master
  • 22,095 Answers

Check oil level

Posted on Oct 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change the oil pan on a 2007 ford f150 4.2L v6?


4.2L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
    WARNING
    During engine repair procedures, cleanliness is extremely important. Any foreign material, including any material created while cleaning gasket surfaces, that enters the oil passages, coolant passages or the oil pan can cause engine failure.
  2. Raise and safely support the vehicle.
  3. Remove the starter.
  4. Drain the engine oil. Install the drain plug when finished.
  5. Remove the 4 bolts and the crossmember.
  6. Remove the 3 oil pan-to-transmission bolts.
  7. Remove the 17 bolts and the oil pan.
  8. Remove and discard the oil pan rear seal.
To install:

WARNING
Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means to clean the sealing surfaces. These tools cause scratches and gouges which make leak paths. Use silicone gasket remover and a plastic scraping tool to remove all traces of old sealant. Follow the directions on the packaging.
  1. Clean the gasket mating surfaces using silicone gasket remover, a plastic scraping tool and metal surface prep. Follow the directions on the packaging.
    NOTE
    If the oil pan is not secured within 4 minutes, the sealant must be removed and the sealing areas cleaned. To clean the sealing area, use silicone gasket remover and metal surface prep. Follow the directions on the packaging. Failure to follow this procedure can cause future oil leakage.
  2. Apply silicone gasket and sealant to the oil pan sealing areas shown and install the oil pan rear seal.
  3. Apply silicone gasket and sealant to the rear main bearing cap.
  4. Install the oil pan rear seal.
  5. Apply a bead of silicone gasket and sealant to the oil pan mating surface.
  6. Position the oil pan and install the bolts. Tighten the bolts in the sequence shown. Tighten to 10 Nm (89 inch lbs.).
  7. Install the 3 oil pan-to-transmission bolts. Tighten to 34 Nm (25 ft. lbs).
  8. Install the starter.
  9. Position the crossmember and install the 4 bolts. Tighten to 90 Nm (66 ft. lbs.).


26094896-ivvnvjgd1uemkjtm4rdse3pw-2-1.gif

Feb 15, 2016 | Ford Cars & Trucks

1 Answer

How do i change out the oil pan?


4.2L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
    WARNING
    During engine repair procedures, cleanliness is extremely important. Any foreign material, including any material created while cleaning gasket surfaces, that enters the oil passages, coolant passages or the oil pan can cause engine failure.
  2. Raise and safely support the vehicle.
  3. Remove the starter.
  4. Drain the engine oil. Install the drain plug when finished.
  5. Remove the 4 bolts and the crossmember.
  6. Remove the 3 oil pan-to-transmission bolts.
  7. Remove the 17 bolts and the oil pan.
  8. Remove and discard the oil pan rear seal.
To install:

WARNING
Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means to clean the sealing surfaces. These tools cause scratches and gouges which make leak paths. Use silicone gasket remover and a plastic scraping tool to remove all traces of old sealant. Follow the directions on the packaging.
  1. Clean the gasket mating surfaces using silicone gasket remover, a plastic scraping tool and metal surface prep. Follow the directions on the packaging.
    NOTE
    If the oil pan is not secured within 4 minutes, the sealant must be removed and the sealing areas cleaned. To clean the sealing area, use silicone gasket remover and metal surface prep. Follow the directions on the packaging. Failure to follow this procedure can cause future oil leakage.
  2. Apply silicone gasket and sealant to the oil pan sealing areas shown and install the oil pan rear seal.
  3. Apply silicone gasket and sealant to the rear main bearing cap.
  4. Install the oil pan rear seal.
  5. Apply a bead of silicone gasket and sealant to the oil pan mating surface.
  6. Position the oil pan and install the bolts. Tighten the bolts in the sequence shown. Tighten to 10 Nm (89 inch lbs.).
  7. Install the 3 oil pan-to-transmission bolts. Tighten to 34 Nm (25 ft. lbs).
  8. Install the starter.
  9. Position the crossmember and install the 4 bolts. Tighten to 90 Nm (66 ft. lbs.).

change-out-oil-pan-v0gljzlk4qz3gwg3khr1r5p1-2-0.gif

Feb 15, 2016 | Cars & Trucks

1 Answer

What are the steps in changing the oil in a 1986 Lincoln Town Car


1) Purchase appropriate oil filter, sump drain bung washer and chosen engine oil.
2) Prepare an oil pan, sump bung wrench and oil filter removal tool (check access to oil filter to be sure that your tool is suitable.)
3) Run the engine until its warm to hot.
4) With the car jacked up and secured, remove engine oil filler cap and remove engine oil sump drain bung and allow oil to flow out into your drain pan. Keep an eye on your oil and make sure it doesn't overflow from your drain pan.

5) Refit sump bung with new washer and tighten. Do not over-tighten, and be especially careful when tightening into an alluminium sump.


6) Remove oil filter. Oil will flow out from this filter when removing, so your drain pan will need to be under the filter housing when removing.


7) Run a smear of clean engine oil around the filter rubber seal and refit new filter. Tighten hand tight only. Do NOT crank this filter super tight as you may damage the rubber seal and even the filter casing which can impede oil flow.


8) Refill engine with proper quantity of oil. If you cannot find how much oil your engine is supposed to take, then refill with the same quantity of oil which you drained out.


9) Restart the engine while checking the oil pressure warning light on the dash. The warning light may stay on for three or four seconds and then go out. If this light stays on for longer, then stop your engine and check for oil leaks at the filter body and sump drain bung.


10) Once the engine oil pressure warning light is off after starting, stop the engine and check the engine oil level (with vehicle on the flat and off any axle stands.)


11) Road test the vehicle, driving it for a mile or two before re-checking for oil leaks under the engine bay and engine oil quantity.

Nov 04, 2012 | Lincoln Cars & Trucks

2 Answers

Oil Is Leaking Out Under The Harminc Balancer On my 92 Jeep Wrangler,4.0 6cyl. I Replaced The Main Seal & Put A New Balancer On & It Still Leaks From The Bottom Of The Balancer


  1. timing cover is leaking oil betwwen cover and block
  2. Disconnect the negative battery cable.
  3. Remove the drive belt(s), fan and fan shroud. If equipped, remove the accessory drive belt pulley.
  4. Remove the vibration damper retaining bolt and washer. Remove the vibration damper using a suitable puller.
  5. Remove the accessory drive brackets attached to the timing cover.
  6. Remove the A/C compressor, if equipped, and alternator bracket from the cylinder head and move to one side.
  7. Remove the oil pan-to-timing case cover bolts and the cover-to-cylinder block bolts.
  8. Remove the timing case cover front seal and gasket from the engine.
  9. Cut off the oil pan side gasket end tabs and oil pan front seal tabs flush with the front face of the cylinder block. Remove the gasket tabs.
  10. Clean the timing case cover, oil pan and cylinder block gasket surfaces.
  11. Remove the crankshaft seal oil seal from the cover by prying it out with a suitable tool.

To install:

  1. Install a new seal in the timing cover using a suitable seal installation tool.
  2. Apply sealer to both sides of the replacement cover gasket and position the gasket on the cylinder block. Cut the end tabs off the replacement oil pan gasket corresponding to those cut off the original gasket. Attach the end tabs to the oil pan with sealer.
  3. Coat the front cover seal end tab recesses generously with sealer and position the seal on the timing cover.
  4. Apply engine oil to the seal-oil pan contact surface, then position the cover on the cylinder block.
  5. Insert timing case cover alignment tool J22248 or equivalent, in the crankshaft opening. Install the cover-to-cylinder block bolts and tighten them to 62 inch lbs. (7 Nm). Install and tighten the oil pan-to-cover bolts to 11 ft. lbs. (13 Nm).
  6. Remove the cover alignment tool and position a replacement oil seal on the tool with the seal lip facing outward. Apply a light coat of sealer to the seal and a light coat of oil to the crankshaft. Install the seal on the timing cover.
  7. Apply a light film of oil to the vibration damper hub seal contact surface. Install the vibration damper using a suitable installation tool.

Do not hammer the damper into place as damage may result to the damper or engine.

  1. Install and tighten the crankshaft vibration damper bolt to 80 ft. lbs. (108 Nm).
  2. If equipped, install the crankshaft pulley and tighten the bolts to 20 ft. lbs. (27 Nm).
  3. Install the accessory brackets.
  4. Install the fan and fan shroud.
  5. Install the drive belt(s) and adjust to the proper tension.
  6. Connect the negative battery cable.
  7. Start the engine and check for leaks
  8. .

Jan 18, 2011 | 1992 Jeep Wrangler

1 Answer

Oil pan removal 3.7


a lot tougher job than in the old days!

The engine oil pan is made of laminated steel and has a single plane sealing surface. The sandwich style oil pan gasket has an integrated windage tray and steel carrier. The sealing area of the gasket is molded with rubber and is designed to be reused as long as the gasket is not cut, torn or ripped

1.) Disconnect negative battery cable.
2.) Remove the radiator fan
3.) Remove the intake manifold you need to do this to install the engine support tool
4.) Install engine support Tool #8534 Do not raise engine at this time but make sure it is tight!
5.) Remove the structural cover
6.) Remove both left and right side engine mount through bolts
7.) Raise engine to provide clearance to remove oil pan.
8.) Drain engine oil and remove oil filter
9.) Remove the oil pan mounting bolts and oil pan.
10.) Unbolt oil pump pickup tube and remove tube and oil pan gasket from engine.

NOTE:Do not pry on oil pan or oil pan gasket. Gasket is mounted to engine and does not come out with oil pan.



reverse to install
do not over tighten bolts
follow normal torque sequence but here's a pic just in case
eabea73.gif


Apr 05, 2010 | 2006 Jeep Commander

1 Answer

How do i change the oil pan gasket


  1. Buy or make a suitable new gasket and enough oil to do an oil change, it is a good idea to change the filter too.
  2. Ensure you have the correct tools.
  3. Drain the oil and dispose of the oil responsibly. Undo the fastenings.
  4. Drop the oil pan/sump.
  5. Clean the adjoining surfaces and ensure they are not damaged. Lightly grease the gasket and fit to the oil pan/sump.
  6. Replace the fastenings to the correct torque.
  7. Replace the oil with the correct quantity.

Sep 27, 2009 | 1995 Dodge Intrepid

1 Answer

New timing belt,oil change, then the car started to overheat,


pan removal requires hanging the motor with a sling and dropping the subframe ...it's a bear but pump and pan can be removed. silicone clogging the pick-up is common

Mar 17, 2009 | 2002 Volkswagen Passat

1 Answer

LOW OIL LIGHT


well when oil is cold its thicker
as the vehicle heats up the oil becomes thinner in the oil pan
in which when the vehicle reaches core temp the oil pump doesnt need to work as hard

heres some other areas to look at
bad oil sending unit
in the pan the oil pick up pump filter needs replacement
oil filter clogged
bad oil sensor
vacume leak
these things need to look for and adjust or replace
the oil pick up pump in pan needs to be serviced by service tech at the dealers this is something a do it yourselfer could not do on own with out proper tools

Jun 07, 2008 | 1997 Dodge Caravan

Not finding what you are looking for?
2006 Pontiac Torrent Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...