Question about 2005 Chrysler Crossfire

Open Question

What size wrench is needed to remove th plug on the oil pan of a 2006 sebring

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1114 Answers

SOURCE: 2001 Concorde 3.2 L Oil Pan Removal

if you have your old drain plug take it to a auto part store get a self tapping drain plug! save big$$$$$ I have installed piles of these they last for ever $5-$20- for one. cheers

Posted on Dec 24, 2008

Murphybanton
  • 2004 Answers

SOURCE: what size wrench do you need to change front brake

10/12

Posted on Jul 01, 2009

  • 23 Answers

SOURCE: loation of spark plugs on 2006 chrysler sebring

They go into the cylinders through the middle of the valve cover.

Posted on Jul 28, 2009

  • 61 Answers

SOURCE: 2004 chrysler sebring oil leak

The solenoid blocks are known to leak. You will need to access this under the hood. The cooling lines well need removed from the trans, disconnect the input speed sensor, and remove it using a 1" deepwell socket. Remove the plug on the solenoid block, using an 8mm socket. You will see 3 tenmm bolts on the top of the Sol block. Remove these bolts, then gently pry the sol block off the trans. Using a scraper, remove all old gasket material from the trans case, be careful not to damage it, then thoroughly clean the mounting surface. Install the new Sol Block, with a new gasket, and torque to factory specs, re-install the input speed sensor (torque to spec), install the cooling lines, and reconnect the Sol Block 8mm screw, be sure to TORQUE all to factory spec, failure to do this could result in you damaging the new Sol block, or trans.Make sure to check the fluid level after the repair is complete, and you should have the TCM reset as well. It is fairly labor intensive, and for a first-timer, it will probably take you about 2-3 hrs to do this, provided you have the proper tools. Good luck.

Posted on Nov 17, 2009

  • 819 Answers

SOURCE: I noticed 2 plugs on the bottom rear of my 2006

i have only ever seen 1.... it is a 13mm hex.

Posted on Jan 25, 2010

Testimonial: "Thank you."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What size wrench should be used on oil pan plug for a 3500 engine?


It requires a 15mm socket. If you only have an SAE socket set available, I believe a 9/32" will do, so long as you take it easy and the bolt isn't locked up... Then you could end up stripping the head.

Sep 20, 2014 | 2008 Chevrolet Impala

2 Answers

I put to much oil in my 97 malibu what do I do


oil drain plug is on the bottom of the oil pan, which is under the engine. a proper sized wrench will remove the oil plug. have a large drain pan ready, (5-6 quarts). You might as well have an oil change done at this time as its just a guess how much oil you remove by quickly re installing the plug while draining. If you do drain just a little oil, keep checking the dip stick to be sure not to add more than needed. Add a 1/4 quart at a time. be sue to tighten the drain plug JUST SNUG.

Mar 18, 2014 | 1997 Chevrolet Malibu

1 Answer

Tools for oil change


You only need a few. You need a wrench or socket that fits the oil pan drain plug. Car makers have used all sizes of drain plugs, don't know Saturn's, anywhere from 13 millimeter to 19 millimeter size wrench or socket. One of them will fit yours.
So one wrench (when you find the right one) and you will need a drain pan to catch the oil. Next you will need an oil filter wrench or tool. There are several types and sizes-when you buy the new oil filter you can get the filter remover that fits your filter . A parts person should be able to help you select the right one. Also buy a small funnel to pour new oil into the engine .And don't forget to have a few rags handy to clean up spills and wipe off areas. That's about all that is normally required.

Dec 21, 2012 | 2004 Saturn ION

1 Answer

Oil change 1994 Cadillac Eldorado


well let me see you have 4.6L engine you need 7.5 quarts of oil with new oil filter.to do the oil change you need large drain pan and oil filter wrench and a metric wrench to remove oil drain plug you need a funnel also.you need first start engine let it run for 5 minutes to warm up thin out the oil so it will flow better.once engine warm up.turn off the engine.open you hood.now safely raise support vechicle on jack stands make sure vechicle parked on solid level ground.place large drain pan under oil pan remove oil drain plug you need a 15m wrench remove drain plug let all old oil drain out until you see slow drip then reinstall oil drain plug dont over tighten drain bolt.then place drain pan under the oil filter then remove oil filter using oil filter wrench or large channel lock pliers.once you remove oil filter wipe oil filter seal surface with clean paper towel.take new oil filter add oil to new filter then install new oil filter hand tight take filter wrench turn oil filter one half more turn dont over tighten will damage oil filter seal.make sure oil pan drain plug is in place. then lower vechicle. remove oil filler cap on the valve cover add new oil to the engine using a funnel to keep from spilling oil all over the valve cover and exhaust manifold.add all 7.5 quarts to oil crank case wait until oil settle down in crank case check oil dip stick oil level should be at the full mark on oil dip stick.dont over fill crank case.once you finished oil level correct crank engine check for oil leaks at oil filter and oil drain plug. if engine running okay you see no oil warning lights you ready wheel and deal.

Nov 20, 2011 | 1994 Cadillac Eldorado

1 Answer

Where is the oil filter on the 2001 chrysler sebring? cant find it.


OIL FILTER IS IN FRONT NEXT OIL PAN BUT HIGHER UP POSITION. OIL FILTER ABOVE THE BOTTOM OF THE OIL PAN WHERE YOU CANT SEE IT.IF HAVE TO RAISE FRONT CAR UP TO SEE IT.NEED SPECIAL FILTER WRENCH TO REMOVE IT.

Apr 13, 2011 | 2001 Chrysler Sebring

1 Answer

What size wrench is needed to remove drain plug on 2006 chevy equinox oil pan


Hi and welcome to FixYa!

Most of the drain plug bolt size is 12mm. You might as well try that.

Hope this helps and thank you for using FixYa! Have a good one!

Mar 06, 2011 | 2006 Chevrolet Equinox

3 Answers

How to give it a oil change


Please read first, and make sure you have everything( did mine the other day, and forgot the filter. 2 trips) we can get you to do this in one easy trip. I do believe in safety first, and will tell you several times. This job takes no more than 30 minutes for a beginner. first the tools, a crescent wrench, or open-box wrench set( between 9/16th to 7/8th.)for the drain plug, a jack, jack stands(safety first), a couple of rags, an oil filter wrench, and an oil catch pan( can get both at the auto parts store). Now the bigger auto parts stores carry a returnable catch pan, to recycle the oil. From the store you will need the filter (store clerk will help you get the right size, just need model, year, and size of engine) and a large container of oil (comes in gallon sizes now. lets jack the truck up( put a brick behind the rear wheels, safety) and now lower to the jack stand on the frame. do both sides. with the catch pan under the oil pan, remove the bolt on the back of the pan (slowly, as you unscrew the bolt, oil will start to leak out, remove the bolt and let the pan drain. now, take the filter wrench, and unscrew the oil filter(careful, its FULL of oil) and set that in the catch pan to drain. Please check the old oil filter to make sure the rubber gasket is still on it. they sometimes stick to the engine block, and the new filter will leak. time to put it together now. taking the new filter, take some oil and rub it on the new gasket(will help with the seal) and screw into place tighten with your hands only(tight as you can(using the wrench might damage the filter). wipe off around the drain hole, and the plug. screw the plug back into place(only tight enough to get a good seal) do not over tighten, it will strip the pan hole. remove everything from under the truck, and take off the stands. refill the oil to the dip stick. and start the truck. Look underneath for any leaks. No leaks. great. let the truck sit for about 15 minutes, and check the oil level (you started the truck, and filled the oil filter). so add the oil you need, and your done. hope this helps you. very easy job to do

Jan 05, 2011 | 1996 GMC Sonoma

2 Answers

How do I change the oil filter on the 2004 pontiac grand am ?


YOU NEED A DRAIN PAN.SAFELY RAISE VECHICLE SUPPORT WITH JACK STANDS ON LEVEL SOLID GROUND.YOU NEED TO REMOVE THE FRONT BOTTOM SPLASH SHIELD.ITS UNDER CAR NEAR BOTTOM RADIATOR.YOU NEED A RATCHET WRENCH WITH SOCKETS SIZES RANGE FROM 13 14 15 METRIC TO REMOVE OIL PAN DRAIN PLUG.CATCH OIL IN DRAIN PAN.BESURE TO WEAR RUBBER GLOVES ON HANDS ENGINE OIL CAN CAUSE SKIN CANCER.AFTER OIL HAS DRAIN OUT IN PAN. SCREW OIL PAN DRAIN PLUG BACK IN PLACE DONT OVER TIGHTEN.THEN YOU REMOVE OIL FILTER USING OIL FILTER WRENCH BESURE MOVE DRAIN PAN TO CATCH OIL WHEN YOU REMOVE OIL FILTER.YOU NEED THE LARGE SOCKET OIL FILTER WRENCH USE A LONG 3/8 EXTENSION TO REMOVE OIL FILTER.WHEN OIL HAS DRAIN OUT AFTER REMOVING OIL FILTER WIPE OIL FILTER SEAL SURFACE WHERE OIL FILTER GOES TO WITH PAPER TOWEL.THEN YOU TAKE NEW OIL FILTER FILL IT WITH HALF OIL RUB OIL ON FILTER SEAL TO HELP IT SEAL BETTER.THEN YOU SCREW NEW OIL FILTER IN PLACE HAND TIGHT IT. YOU NEED AT LEAST 5 QUARTS OF ENGINE OIL.CHECK TO SEE HOW MANY QUARTS OF OIL YOUR CAR HOLDS.GRAND AM HOLDS FROM 4.0 TO 4.5 QUARTS OF OIL.BEFORE POURING IN NEW OIL MAKE SURE OIL PAN DRAIN PLUGS IN PLACE AND TIGHT DONT OVER TIGHT YOU CAN STRIP THE DRAIN PLUG.YOU POUR YOUR OIL BACK INTO ENGINE FROM TOP UNDER THE HOOD LOOK FOR A CAP THAT SAY OIL FILL CAP ON THE FRONT VALVE COVER.USE A FUNNEL TO KEEP FROM GETTING OIL ON EXHAUSTMANIFOLD.CHECK OIL LEVEL USING DIP STICK WHEN YOU POUR OIL BACK IN THE ENGINE.THE OIL LEVEL SHOULD BE ON THE FULL MARK ON DIP STICK DONT OVER FILL.IF YOU OVER FILL YOU CAN REMOVE OIL DRAIN PLUG TO REMOVE EXCESS OIL.WHEN JOB FINISHED OIL LEVEL IS RIGHT.CRANK CAR CHECK FOR OIL LEAKS. IF OIL FILTER LEAKS A LITTLE HAD PROBLEMS GETTING IT TIGHT TAKE OIL FILTER WRENCH TIGHTEN A LITTLE MORE DONT OVER TIGHTEN DAMAGE THE OIL SEAL HAVE A BIG OIL LEAK.BEFORE DOING THIS JOB GO TO AUTO PARTS PLACE TELL THEM YOUR ENGINE SIZE AND YEAR MODEL OF CAR SO YOU CAN GET THE RIGHT OIL FILTER.WARNING BEFORE DOING THIS JOB HAVE RIGHT AMOUNT OF OIL AND FILTER.MAKE SURE YOU HAVE ALL THE TOOLS FOR THE JOB.IF YOU ANY PROBLEM A HAYNES REPAIR MANUAL CAN HELP A LOT.

May 03, 2010 | 2004 Pontiac Grand Am

1 Answer

Oil sending unit on 2004 chrysler sebring V6


Should be located close to the oil filter. It will screw in like a spark plug. It has a harness plug. Easy to change, save yourself $70 in labor. You will need a fairly large wrench to remove

Jan 03, 2010 | 2004 Chrysler Sebring

1 Answer

What is the size of the allen wrench needed to fit the oil pan drain plug in a 1995 toyota celica


The oil pan drain plug should require a 14mm hex head wrench to remove. The transmission pan requires a 10mm allen head socket, or wrench to remove. Are you sure you're trying to remove the correct drain? The oil drain should be on the passenger side and on the rear corner of the pan.

Dec 12, 2009 | 1995 Toyota Celica

Not finding what you are looking for?
2005 Chrysler Crossfire Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...