Question about 1996 Volvo 960

1 Answer

1996 Volvo 960

There is only the two bolts, right ? And then is should come out the little hole that there is? Thanks for all of your help!!!! I need it. Scott

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert that hasĀ over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 241 Answers


Posted on May 29, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

How to adjust cam shaft mark to cam gear

Need help with what Thanks Viper

Sep 14, 2008 | 1996 Volvo 960

1 Answer

Hand brake on volvo 960, 1996 does not hold.

remove the ash tray and holder from rear of praking brake cover.use a screw driver and hammer to tap sleeve to free from adjusting screw, now adjust the cable. hope this helps.

Jan 30, 2010 | 1996 Volvo 960

1 Answer

How do get to and adjust handbrake cable on my 960 volvo

make sure e-brk shoe adjuster is all the way closed. then start adjusting little by little until you can slide disc back on and have a little friction when you spin it by hand, also hope your replacing dics, old one sometime have lots of rust stopping disc from going on anyway good luck and hope this helps.

Oct 20, 2009 | 1996 Volvo 960

1 Answer

Passenger seat doing the same thing

I have a 95 960 wagon and my seats have circuit boards

Sep 24, 2009 | 1996 Volvo 960

1 Answer

1996 960 volvo trouble code 715

That trouble code is the input speed sensor. It is bolted on externally. If you have had any recent work in the area directly above the trans axel, someone may have unhooked it. It is located at 12 o'clock right about the middle of the trans.

A good diagnostician with a scanner can hook up and drive and be able to see the impulse from that sensor. It can be replaced without a major amount of work, however it is a little hard to see. (I think you will find it under the cooler lines, but it has been a few years since I worked on one.

Hope this helps.

Sep 12, 2009 | 1996 Volvo 960

1 Answer

My 1996 Volvo 960 2.9 ltr drives in all Position except reverse

I am not 100% but this should be a good place to start and it will cost you nothing. You need to get under the car. You will see that there is a thin long shaft that is theaded on the end. It should have a rubber gromet at the connector. I believe that your gromet is worn out or perhaps you need to simple adjust the threaded end to be tight as your shifter is traveling to far. I am not an expert, but I have been all over my 960 for the past 261K miles and 10 years of ownership.

Good luck.

Mar 29, 2009 | 1996 Volvo 960

2 Answers

I need to remove the car battery from a 1996 960 volvo sw.

moz-screenshot.jpgThe hold down bolt is a @ 10inch long think bolt with an eye/thumbscrew at the top next to the front of the battery. Mine was severed at the level of the battery top by electrolytic corrosion, so the top was missing.

I removed it with small vice-grip pliers but it was hard to reach in the confined space. This is the replacement part I found on line

w01331633889mtc.jpg Click to Enlarge
MTC Battery Hold Down Bolt Retail Price: $8.92 Your Price: $4.25 Quantity: Part Number: W0133-1633889moz-screenshot-1.jpg

Mar 20, 2009 | 1996 Volvo 960

1 Answer

How to change spark plugs in a '96 Volvo 960

Remove the torx 30 screws that hold the plastic cover on the top of the engine,then you will find 10mm bolts holding coils to cyl head,remove bolts,lift coils out of spark plug holes,remove and replace spark plugs

Oct 01, 2008 | 1996 Volvo 960

1 Answer

Starter Replacement in a "96" 960

Disconnect the battery and wires going to the starter. If air charge tube is in the way you can remove it. I am not looking at a S-70 turbo right now but sure that I have never had to remove intake to R&R a starter. There might be a bracket on the passenger side of starter with a 12mm bolt into the front of the engine and two 10mm nuts onto the starter. Remove two 13mm stud bolts that hold starter in place and slide out. New starter goes in reverse order.

May 29, 2008 | 1996 Volvo 960

Not finding what you are looking for?
1996 Volvo 960 Logo

Related Topics:

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts


Level 3 Expert

77939 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides