Question about 2006 Hyundai Sonata

1 Answer

Will not move in rverse - 2006 Hyundai Sonata

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 17,970 Answers

Hyundai Sonata transmissions were much less than reliable. In most cases, the symptoms you describe are caused by an internal transmission failure that will require an overhaul or replacement. To be sure, however, you should check the shift cable and the adjustment and operation of the inhibitor switch. If that's good, you can pretty much draw the conclusion that you're looking at expensive repairs.

Cost will vary greatly by geographic location and the shop where you have the vehicle repaired. You'd be best served by calling a few places to see what they'd charge to overhaul or replace the transmission with one that's already been remanufactured. Be sure to call your local Hyundai dealer also. Hyundai prices their remanufactured transmissions very competetively, so many dealers sell them for less than Hyundai's list price.

I hope helps with this; keep us updated (remember to rate this).

Posted on Oct 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Has all forward gears but no rverse


if its internal the low reverse band could be slipping. What car is it and check to see if you have a tranny code if it has a computer.

Dec 10, 2015 | Cars & Trucks

1 Answer

My 96 ford taurus revs high when starting then works it way from 1500 or more down to 800 but fluctuates from 800 to a little over 1000. When putting car in rverse or drive from park engine revs up to...


You need to clean the IAC again and also the throttle valve and bore, use only CRC brand Throttle body cleaner. After they are thoroughly cleaned disconnect the battery for 5 min's and then drive the car in varying condition for a few days. If that doesn't cure the issue you have more serious problems and will need a scan tool to look into the readings from the MAF, TPS and ECT sensors. High idle cold start is normal then slowly dropping after a few minutes. I assume you never had a check engine light. Correct?

Mar 24, 2017 | 1996 Ford Taurus

1 Answer

When I start the car and try to rverse it will not move.. i dont know if it will go forward because i can not get out of the park to see.


try letting the car warm up for about ten minutes then have a friend help, try rocking the car back and fourth and shifting it sounds like your transmission in stuck in between park and reverse. this may help also you might try to step out of the car with a friend holding the break try and shift the car manually from under the hood. Let me know if this helps.

Feb 23, 2011 | 2001 Pontiac Grand Am SE

1 Answer

I have a 2006 Nissan Maxima 3.5 SE. I believe the transmission is going out on it, had the transmission flued replaced, but the dealership does not want to listen to me and asked me to take it to another...


let me guess its a five speed automatic tha toperates perfectly when cold but the longer you drive and the hotter it gets the worse it performs?these unts have a very high notoriety for shift valves stiicking in valve body when hot.....slip shift shock on down shift and delayed ,harshengagement from rverse to drive etc.put a valve body in it as long as fluid is not black....brown is ok,and you will be good to go.please let me know how it comes out.

Feb 08, 2011 | 2006 Nissan Maxima

1 Answer

Where is my starter located on my 96 Lesabre and how do i get to it


You will have to disconnect the battery positive cable, jack the car up so that you can gain access from the bottom. It is located in front of the engine facing the engine, There is a plastic cover that goes around the starter that should be removed. It takes ten mm wrench or socket to remove the cover. There are two large bolts that hold the starter in place, they go through the bottom of the starter. Use a 15 mm socket to remove the bolts. There is two wires that are attached to the back of the starter. It takes a 13 mm socket or wrench to remove the large one a 8mm socket to remove the small wire. Once removed slide the starter out and rverse procedure to install.

Jul 03, 2010 | Cars & Trucks

1 Answer

I have a problem with the reserve on my car sometimes it works and sometimes it doesn't when I can't get reserve first and second gear is in reverse position on Volskwagen Passet 1994


pardo me for asking but is there not a method of selection of rverse gear by either pressing or lifting the gear lever so it will move over further so as to select reverse? or a lift up circular boss on gear lever itself that has to be lifted then reverse position can be selected ? hope this helps ?

Dec 19, 2009 | 1997 Volkswagen Passat

1 Answer

Rebuilding 1995 honda civic transmission


Did you make sure that the tork converter was all the way forward first if not then you will need to take the transmission back out and make sure that the converter has either automatic trany fluid in it or 184/85 gear oil depending on whether or not you have automatic trasmission or manual fill it up until you can put your finger in it and then rotate converter clock wise and it should slip into place before putting trasmission back into car and if after doing that and you still are having trouble take it to a transmission shop to have them do it for you.

Sep 14, 2009 | 1995 Honda Civic

1 Answer

***FROZEN IGNITION LOCK CYLINDER***


Necessary to remove air bag, steering wheel ( puller needed ) , signal switch, With key in switch , using flat blade screwdriver depress tab , and slide old lock cylinder out. Rverse installation. Make sure NEW lock is coded to ORIGINAL ignition key. Hope this helps.

Apr 07, 2009 | 1986 GMC Safari

1 Answer

Rverse lights stay on


The reverse light switch is stack in an on possition.

Jan 30, 2009 | 2004 Renault 181

Not finding what you are looking for?
2006 Hyundai Sonata Logo

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...