Question about Chevrolet G30

1 Answer

1989 1 ton chevy van model 30 automatic trans, dies when turn to the right, someone put a new ing. switch in it, and you can can pull the tumbler out with the van running, may be hitting something when you turn to the right, will not die turning to the left.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 766 Answers

OK check for any obstruction that might play a part in obstructing free movement of the steering mechanism when turning right. Next compare the ends of the left and right hands end of the steering rack The steering arms are held in the middle of the steering rack ends by a doughnut shaped bush bearing. If this has been damaged the rack will be dragging on the inside of the casing when the steering is turned in one direction. It could be that the end bearing on the left is shot and this is what is obstructing the turn to the right. The next thing to take care of is the fact that you have the engine stalling under load. This points to an idle speed control problem. Check that the throttle body interior and throttle plate are really clean and that the idle speed control valve on the throttle body is actuating properly. If suspect unbolt and give this a thorough interior clean out.

Posted on Oct 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1988 chevy suburban 1/2 ton auto trans; 4 wd; dies after putting into drive


Could be a dirty throttle body or faulty idle air control valve.
Is the check engine light on ?

Jul 09, 2012 | Chevrolet Suburban Cars & Trucks

2 Answers

Starter key switch wont turn


MORE THAN LIKELY THE ING SWITCK / KEY AND TUMBLER NEEDS TO BE REPLACED, BUT TRY TO MOVE THE STEERRING WHEEL RIGHT OR LEFT COULD BE HUNG IN LOCK POSSION

Jan 10, 2012 | 1999 Chevrolet Malibu

2 Answers

Cant get key switch out of housing, on a 1974 chevy pick up.Trere are no screws or clips visible.


If you mean remove the ignition tumbler from the steering column, you will have to remove the steering wheel and lock plate, then you will need to remove the turn signal lever and screws, and then pull the turn signal switch up and out of the way, you should then be able to see the housing for the ignition tumbler down in the steering column. Look at the tumbler housing and there should be a small slot towards the end of the housing that you can put a small standard screwdriver into and depress a locking latch that is built into the tumbler. When this latch is depressed you will be able to pull the ignition tumbler straight out of the column.

Apr 19, 2010 | 1986 Chevrolet Chevy

1 Answer

I have an 89 chevy sport van and it runs for a little while and then just dies we had a new fuel pump put on along with the new hoses but could this be a bad ECM causing the van to just stop running?


I would not go that far yet.Replace the ignition module in the distributor first.It is the most likely problem.It is common on these models to do this.

Dec 12, 2009 | 1989 Chevrolet C/K 3500

2 Answers

Security light is blinking - GMC 2500 van won't start


replace the ignition lock cylinder, that should cure the problem, but u will need to have the VATS module re-programmed to accept the new VATS key resistance value, this is preformed by the dealer only.

Sep 14, 2009 | 1998 GMC Jimmy

3 Answers

1989 Chevy truck. The key is stuck in the run position. I can turn it to start and it returns to run. I cannot turn it to off. Do I remove the steering wheel to access the tumbler? What am I looking for to...


yes remove the wheel, lock cylinder is wore out. with wheel off, key in on position look for a small slot looking you in the eye, put a nail file in it to release the spring tab and pull cylinder out. buy new one at auto parts store first to look at if you can youll see how to alot better they are fairly simple. good luck!

Sep 03, 2009 | Chevrolet C2500 Cars & Trucks

1 Answer

1993 chevy 3/4 ton van


The clutch pack in the trans has failed, u have no choice but to overhaul it.

Dec 11, 2008 | 1993 Chevrolet S-10

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...