Question about 1992 Honda Accord

1 Answer

The light on the dashboard panel for the D4 does not light up. The other lights for P,R,D3,1 and 2 light up.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 863 Answers

You gots ta get behind there and replace the bulb that burned out.

Posted on Oct 10, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 honda accord d4 light out


why is my 2002 Honda accord ex d4 light is out

Jan 24, 2012 | 2002 Honda Accord

1 Answer

D4 light on no matter what gear i'm in. 95 Honda Accord LX 4-cylinder. Already replaced solinoid, speedometer, fan,


The D4 light is coming on to tell you that there is one or more fault codes set in your transmission control module. The only way to retrieve codes on the 1995 models is to read "Flash Codes" output by the D4 light. (See instructions below)

RETRIEVING FLASH CODES USING THE D4 LIGHT
If fault codes are present, the D4 light will "blink" when the ignition is turned to the RUN position and will remain on at all times when the engine is running.
To retrieve the flash codes, turn the ignition switch off.
Install a jumper wire between the service check connector terminals.
The service check connector is a gray, 2-pin connector located on the PCM/TCM cover under the passenger side of the instrument panel. (See picture below)

CAUTION: DO NOT use the 3-pin located next to the service check connector.

Installing the jumper will place the PCM/TCM in diagnostic test mode.
Turn the ignition to the RUN position. Codes will be output by blinking the D4 light.
Note the number of blinks from the D4 light. A short blink indicates a single digit flash code. A long blink equals 10 short blinks. For instance one short blink indicates code 1. One long blink and four short blinks indicates code 14. If there is more than one fault code, they will be output one at a time from the lowest numbered code to the highest numbered code. It is recommended that you read the code or codes several times to make sure that you are reading it correctly.

Once you have retrieved the fault code(s) re-post your question and include the information for what codes you have and someone can then help you locate the cause of the problem.

May 22, 2011 | Honda Accord Cars & Trucks

1 Answer

This my sec trans and the d4 light cont to blink, replace tcm (brand new) now the car stays in sec. gear & d4 light is on but not blinking. so I place old tcm back in and the car drove d4 still remain...


you have problem with your transmission computer located under your dashboard behind your radio comparment i had the same problem replaced that for a used one or rebilt one and solve
just make sure they sincronized again with transmission

May 04, 2011 | 1992 Honda Accord

1 Answer

The d4 light on the panel is flashing...What is that?


The transmission computer has self diagnostic capabilities.When the computer sees a problem it flashes the d4 light.You will need to have codes pulled to find out what is going on.Most transmissions shops and some general repair shops can handle this for you.Good luck!

Mar 02, 2011 | 1994 Honda Accord

1 Answer

"s" on dashboard what does it


It means your transmission control unit (TCU) has detected an issue in your transmission...probably a bad sensor. Click here to diagnose the problem. That link is a post for 92-93 accords where the D4 light is for TCU errors, but diagnosing is the same. Just replace every instance of "D4 light" with "S light".

Jan 31, 2011 | 1991 Honda Accord

1 Answer

Blinking D4 drive gear in the dashboard


you need to check the codes for the trans first.
have to contact the honda dealer for a radio code.
needs a clock light bulb.

Nov 12, 2008 | 2002 Honda Accord

4 Answers

D4 LIGHT


rate me FIXYA!...thanks
44926db.jpg
f77bb4e.jpg
52a3c74.jpg

Jul 05, 2008 | 1992 Honda Prelude

2 Answers

D4 gear lights ( dashboard ) starts blinking even I'm using other gears


The D4 light blinking is the vehicle computer telling you there is a transmission malfunction and transmission codes are stored in the computer's memory.The codes have to be pulled out manually unless it has an OBD2 connector.A transmission shop or Honda dealer can pull the codes.

Jun 22, 2008 | 1995 Honda Odyssey

Not finding what you are looking for?
1992 Honda Accord Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...