Question about Ford Focus

1 Answer

2001 steel wheel what is the correct torque setting for nuts please

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,926 Answers

95 ft lbs.

Posted on Oct 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2001 GMC Seirra Truck 4wheel drive 5.3L. Torque specs for lug nuts?


2001 GMC Truck Sierra 1500 4WD 5.3L SFI 8cyl

The Lug Nut Tightening Torque 140 Foot pounds (Final torque).

Oct 06, 2015 | GMC Cars & Trucks

1 Answer

How do I remove and change ignition switch in a mazda bravo 2001 ute?


Hi, 1st you need to take off the steering wheel, if the horn does not just pop off, check for 3 torque bit 8mm at the back of the steering wheel, they could be star point screws, depending on where is was built. be sure your wheels are true straight, and lock ignition so wheel not turn, it makes it easier to put the s wheel on true again, With the nut keeping the s wheel on, just crack it a little, then with a brass drift, give it a good hard quick hit, as its on a spicket & can cold freeze on, some come off easy, but what ever you do, don't flog nut with hammer, use brass as its softer than tempered steel,
Once you have s wheel off, 3 screws under the column, 2 one side of the tilt lever & one the other side, make sure u note which one come out of what holes, as they differ in length, then pop off the top plastic cover, ( un clip airbag wire from horn pad, ), no need to disable battery), once both cover are off, you will see 2 screws holding the ignition lock in place, could be torque head, or just a 8 mm nut,) unclip the plugs, and take out , do the reverse to fit back together, if you source on from Auto Wreckers, make sure it has the correct key, to suit that ignition, as they are coded, Good luck
K

Nov 26, 2014 | Mazda Cars & Trucks

1 Answer

Torque setting for wheel nuts on Renault Alloy wheels


130(NM) 96 ft/lbs is the torque setting for a 2008 renault scenic so as not to ruin studs or brake rotors should be sufficient for allloys just need to check alloy lug nuts more often

Aug 09, 2014 | Renault SCENIC Cars & Trucks

2 Answers

Lug nut torque chart


Here's a handy link to the wheel nut torque settings for hundreds of different vehicles.
Look your's up........and away you go!
http://www.discounttiredirect.com/infoCenter/infoWheelTorque.html

Jul 30, 2014 | 2004 Pontiac Montana

1 Answer

Torque specs bearing


Honestly you should search google. It is right there. the inner hub nut must be torqued to 59 Nm rotate the hub three times in each direction and then loosen the inner hub nut until it can be turned by hand, then again tighten the inner hub nut to 25 Nm. the lockwasher against the inner hub nut, it only goes in one way, it has a small inner tab that locates with the key way of the hub, this is between the threads. Once the lock washer is in the correct position, you can now install the outer hub nut, this outer nut must be torqued to 47 Nm, once you have tightened this outer nut, please once again check that the starting effort is correct.

Oct 18, 2013 | 2007 Toyota Hilux 2.5

1 Answer

Need to know the torque setting for the rear weel bearing on my 2001 ford focus. it takes a 30mm socket.


The torque setting 49 ft. lbs.


Torque Specifications
Description Nm lb-ft lb-in Wheel nuts - steel/alloy wheels 128 94 - Wheel spindle retaining nuts 66 49 - Wheel cylinder retaining bolts 12 9 - Rear brake pipe to wheel cylinder union 8 - 71 Rear wheel speed sensor retaining bolt 9 - 80 e0001241.jpg
Item Part Number Description 1 - Tie bar and knuckle 2 - Backing plate 3 - Wheel spindle 4 - Sensor ring - anti-lock control 5 - Grease cap 6 - Wheel bearing retainer 7 - Drum

Apr 26, 2011 | Ford Focus Cars & Trucks

1 Answer

2001 chevy silverado steering wheel vibration problem


bent alloy, bent steel rim, broken belting inside of tire(caused from hitting a good size hole). lug nuts not torqued to correct ft lbs, outer or inner tie rods, toe/ cmber out of adjustment. Are the tires wearing? If not, forget the camber/toe

Dec 14, 2009 | 2006 Chevrolet Trailblazer

1 Answer

Wheel nut torque wrench settings for Seat Toledo V5 November 2001 model.


14mm bolt 100 ft lbs 12mm bolt 80 ft lbs. if you drive real fast on 14mm bolt I like 120ft lbs

Apr 24, 2009 | 2001 Volkswagen Golf

1 Answer

Torque rating for 2005 cavalier lug nuts


Steel wheels or aluminum wheels? Steel-85 ftlbls. Aluminum- 100ftlbs

Mar 27, 2009 | 2005 Chevrolet Cavalier

1 Answer

Torque for front lug nuts on 1997 GMC G3500 Savanna


140 foot pounds as per the GM specs.you can verify the spec online by going to alldata online

May 18, 2008 | 1991 GMC G3500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...