Question about Ford F-250

1 Answer

2005 f250 5.4 gas need to know specs for timing a diagram would be awesome

Posted by on

  • Jeff Turcotte
    Jeff Turcotte Oct 07, 2010

    ignition or valve timing?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,826 Answers

To Install:

  1. Install balance shaft drive gear onto the left camshaft.
  2. Install the camshaft sprockets and new bolts finger tight.
  3. Using a vise, compress the timing chain tensioner plunger.
  4. Install a retaining clip on the tensioner to hold plunger IN during installation.
    marking timing chain 2005 f250 5.4 gas need - a0038720.gif

  5. If timing chain copper links are not visible, mark 2 links on one end and 1 link on the other end to be used as timing marks.
  6. Install right and left timing chain guides. Tighten bolts to 89 in-lbs (10 Nm).
  7. Rotate the left camshaft until the timing mark is at the 12 o'clock position.
  8. Rotate the right camshaft until the timing mark is at the 11 o'clock position.
  9. Position the crankshaft using the special tool. Then remove the tool.
    Crankshaft special tool positioning n0013602.gif

  10. Install the crankshaft sprocket with flange facing forward.
    Crankshaft sprocket timing mark n0011528.gif

  11. Position lower end of left (inner) timing chain on the crankshaft sprocket. Align the copper (or marked) chain link with the timing mark on the outer flange of the crankshaft pulley. NOTE: Upper half of timing chain must be below the tensioner arm dowel.
  12. Position the left timing chain on the camshaft sprocket. The timing mark on the camshaft sprocket must be aligned between the 2 copper (or marked) chain links.
    Left camshaft sprocket timing mark

  13. Place the left timing chain tensioner arm on the dowel pin and install the timing chain tensioner and bolts. Tighten bolts to 18 ft-lbs (25 Nm). NOTE: Lower half of timing chain must be above the tensioner arm dowel.
    Crankshaft sprocket timing mark a0079624.gif
  14. Position lower end of right (outer) timing chain on the crankshaft sprocket. Align the copper (or marked) chain link with the timing mark on the outer flange of the crankshaft pulley.
    Right camshaft sprocket timing mark a0041104.gif

  15. Position the right timing chain on the camshaft sprocket. The timing mark on the camshaft sprocket must be aligned between the 2 copper (or marked) chain links.
  16. Place the right timing chain tensioner arm on the dowel pin and install the timing chain tensioner and bolts. Tighten bolts to 18 ft-lbs (25 Nm).
  17. Remove the retaining clips from the right and left timing chain tensioners.
  18. Verify alignment of all timing marks.
  19. Install crankshaft sensor ring on crankshaft.
  20. Locate index mark on balance shaft and mark corresponding gear tooth with chalk.
  21. Position balance shaft on journals. NOTE: It may be helpful to use an inspection mirror to view the marks timing marks.
  22. Align the chalk mark on the balance shaft with the camshaft timing mark.
    Balance shaft bearing caps 2005 f250 5.4 gas need - n0007112.gifp://arrc.epnet.com/autoapp/FORD_F250-550_05-07_F/p5images/N/N0007112L.gif">n0007112.gif

  23. Install the balance shaft bearing caps in their original locations. Follow the tightening sequence as shown in the illustration. Tighten bolts to 89 in-lbs (10 Nm).
  24. Tighten the camshaft phaser sprocket bolts in the correct sequence using 2 steps, as follows:
    • Step 1-30 ft-lbs (40 Nm)
    • Step 2-tighten an additional 90 degrees
  25. Position the crankshaft keyway in the 11 o'clock position.
  26. Lubricate and install all camshaft roller followers. WARNING
    Engine front cover replacement procedure must be completed within 4 minutes or entire procedure must be repeated. Failure to do so may result in future leaks

Posted on Oct 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ignition module diagram


2007 2.7L hilux
what country is this car, (1million posts and not 1 said yet)
this is USA forum.
Seventh generation (AN10, AN20; 2005-present) 2.7 L 2TR-FE I4 engine. Gas too.

go to your country Toy dealer
and ask for the factory service manual
read the ignition chapter, and wiring chapters
bingo.


or online books dont have your car, only usa spec cars.
here.
or join a toy forum in your country is a win, big time.

Aug 18, 2014 | 2007 Toyota Hilux 2.7

1 Answer

I need to see the diagram of the motor belt.


kevykev39.jpgHope this helps you. Please leave me an awesome feedback on here.

Jan 07, 2011 | 2005 Pontiac Vibe

1 Answer

Need to get timing spec and locate timing marks for 2001 volkswagen beetle 2.0 engine


Click on the following free, direct Link. It has two sets of Diagrams including the Timing + Marks: Belt Diagrams for your 2001 Volkswagon Bettle 2.0L SOHC 4-Cylinder. The other set of Diagrams is for the 1.8L DOHC 4-Cylinder. Further it has Instructional and Directional Diagrams that will help you out.

Let me know if this helped....

http://www.2carpros.com/car_repair_information/year/2001/make/volkswagen/model/new_beetle/2001_volkswagen_new_beetle_timing_belt_diagram_marks.htm

Apr 22, 2010 | 2001 Volkswagen Beetle

1 Answer

I need the timing marks 4 a 2005 spectra i just changed the timing belt


Click on the following direct Link. It has the Timing Belt Diagrams with Marks for the Camshaft and Crankshaft that you will need; although the quality of the diagrams are not that great. It also has numerous other helpful diagrams for use.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/2005/make/kia/model/spectra/2005_kia_spectra_timing_belt_diagram_marks.htm

Nov 22, 2009 | 2005 Kia Spectra

1 Answer

Need timeing specs on toyota pick up truck veic label


Click on the following free direct Link. It has the Timing: Belt and Mark Diagrams for your 1986 Toyota Pickup. Plus additional Instructional and Directional Diagrams.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1986/make/toyota/model/pickup/1986_toyota_pickup_timing_belt_diagram_marks.htm

Nov 09, 2009 | 1986 Toyota Pickup 4WD

1 Answer

I need a timing belt diagram for a 2005 chrysler sebring


My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.
I have only been a free contributor to this site for the past 4-months.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Belt Diagrams you will need.

If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!

Again my apologies...
http://www.2carpros.com/car_repair_information/year/2005/make/chrysler/model/sebring/2005_chrysler_sebring_timing_belt_diagram_marks.htm

Mar 27, 2009 | 2005 Chrysler Sebring Conv

1 Answer

Timing belt diagram for 2005 1300 hyundai getz


My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.
I have only been a free contributor to this site for the past 4-months.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the 2005 Hyundai Accent Timing which have Timing Belt Diagrams very similiar to what you will need.

If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!

Again my apologies...
http://www.2carpros.com/car_repair_information/year/2005/make/hyundai/model/accent/2005_hyundai_accent_timing_belt_diagram_marks.htm

Mar 23, 2009 | Hyundai Motor 2000 Tiburon

1 Answer

Gas tank wont' fill to specs


Based upon my experience, I would say it's a manufacturing defect. Something in the filler or the tank itself. I've seen cases where the dealer replaced the tank and related parts when this is happening.

Nov 17, 2008 | 2005 GMC Yukon Xl Denali

1 Answer

Brakes canyon 2005


you might have the brake shoes adjusted out too much, back them off a little bit and far as the sensor goes, its located on the fuel rail where the injectors are.

Aug 24, 2008 | 2005 GMC Canyon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...