Question about 1990 Ford F350

1 Answer

Will not start in morning. Have to use starting fluid. Will not start when key is in start position. Had to install push button direct to starter to turn engine over. Is this a glow plug problem and how hard would it be to fix myself?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 14,036 Answers

MOST TIME GLOW PLUG CONTROLLER ON THE REAR OF INTAKE MANIFOLD CAUSES GLOW PLUG PROBLEMS.YOU HAVE TO USE 12 VOLTS TEST LIGHT TO SEE IF POWER GOING TO GLOW PLUG CONTROLLER.IF NOT YOU HAVE BLOWN FUSE OR FUSE LINK.IF POWER GOING TO GLOW PLUG CONTROLLER.THE CONTROLLER IS FAULTY OR THE ENGINE TEMPERATURE SWITCH IS BAD.

Posted on Oct 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2006 Ford Expedition will not start this morning, battery checks 12 volts, will not do anything when turn key to start position


You can jump starter relay to see if starter will crank the engine. Pull the starter relay, use jumper wire between terminals 30 and 87, terminal 30 is hot all the time and there is a fuse, the starter motor should crank the engine. If you try that make sure tranny is in park or neutral and parking brake is set. Two voltage circuits at starter motor, one is hot all the time. The other goes hot when relay is energized. The starter motor grounds through engine block. Battery positive and negative connections are important.
starter-xyhkswavnwbj1ruhj1l5cg0h-1-0.jpg

Nov 18, 2017 | 2006 Ford Expedition

1 Answer

How do you hook up a push button start on a 1992 Honda accord ex


You will need to either splice or direct connect one of the leads to a push button starter to the starter solenoid. from there one fused wire to battery positive. And there you have a push button starter here is the danger of doing this if you are in gear with the key on or off and the button is accidently engage it can take off with you in the car or not so extreme safety needs to be practiced at all times

Feb 22, 2012 | 1992 Honda Accord

2 Answers

I have a 2007 press button start toyota fielder wagon.The problem is every morning when i start my car the starter keeps turning over although the car has already started.It sounds as if the starter is...


I'm not familiar with this model Toyota, but I once fixed a similar problem by spraying WD-40 lubricant into the ignition switch. It was sticking in the "start" position, keeping the starter engaged.
Try lubricating your push-button switch. If that doesn't work, replace it.
The repair place might have thought the starter solenoid (which supplies the serious electricity to the starter motor) was sticking "on," but that's unlikely. Those solenoids usually fail in the off position. So it's quite possible there was nothing wrong with your original starter ... and you might want to discuss that with your repair place if the button turns out to be the problem.

Dec 24, 2017 | Toyota Corolla Cars & Trucks

2 Answers

It's a 4 button prostart remote starter. When i push the start button, the lights go on but the van doesn't start


put your key in the ignition switch leave it in the off position, press the remote start button, if it starts and you did not install a transponder bypass modual in it you will require one, if you need one let me know as I stock this item

Nov 19, 2009 | 1998 Chevrolet Venture Cargo

1 Answer

Installed Push Button starter now wont start


you have a short in the push button you should replace this and that that should solve it.........please rate this...thanks

Sep 01, 2008 | 1990 Ford F150

1 Answer

Starter switch


You'll connect one side of the button to constant 12v. like the battery positive and the other side of the switch will go to the trigger wire of the starter. This is the wire that tells the starter what to do.

Jul 01, 2008 | 1993 Pontiac Bonneville

Not finding what you are looking for?
1990 Ford F350 Logo

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...