Question about Dodge Daytona

1 Answer

I AM MISSING A STIK ON LEFT SIDE OF STEERING WITH IT YOU CAN TURN SIGNAL RIGHT OR LEFT. I HAVE DODGE DAYTON 1990-2.5 ENGINE.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,044 Answers

Simple replacement job. Order a Turn Signal control replacement for your vehicle and when it arrives, open the steering column and install the new control assembly. The old one should unplug and teh new one should plug right in. 30 minutes repair job.

Posted on Oct 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where does the flasher go?


Remove the lower dash trim covers from the left side of the Cadillac's dashboard, if so equipped.
    • 3
  • Lie on your back under the left dashboard and look up along the left side of the steering column. Illuminate the area with the flashlight to assist in locating the old turn signal flasher, which mounts on a metal bracket, just above and to the left of the steering column.
  • 4Grab the old flasher by hand and pull it off the bracket. Depending on the model of your Cadillac, you may need to push aside some wiring harnesses to grasp the flasher.
  • 5Plug the new turn signal flasher onto the bracket. Reinstall the lower dash covers, if you removed any in Step 2.
  • 6Place the key in the ignition. Turn the key to the "Run" position.
  • 7Activate the turn signals on the left side of the car and get out and inspect them to make sure both front and rear bulbs are blinking, as designed. Switch the turn signal lever to activate the right signals and visual inspect
  • Jun 24, 2012 | 1990 Cadillac Eldorado

    1 Answer

    Left and right signals don't work. Where should I start looking?


    i would check the turn signal flasher,under the dash on drivers side.on the driver side of steering column on a bracket.

    Feb 01, 2011 | 1990 Pontiac 6000

    1 Answer

    Right rear signal works but the left does not. Changed bulbs twice and still have problem


    Look inside under the steering wheel to the left,remove the lower steering column cover and knee pad panel to see junction box. The each fuse and relay will be marked for the right turn signal and the left turn signal. Look for a blown fuse on the left side. If not then the relay will be at fault. Before you start look to see if either turn signal lights are working on the left side. If the front is working and the rear is not then it will ba a short in the wiring to the rear causing the problem. Hope this will help you.

    May 23, 2010 | 2005 Dodge Grand Caravan

    2 Answers

    Can't find where blinker fuse is on a 1990 mazda b2200 truck


    The fuse panel is located under the left side of dash.
    The turn signal is fuse #6 a 10amp fuse.
    Hope this helps.

    Feb 28, 2010 | 1990 Mazda B-Series

    2 Answers

    Head lights wont stay on


    Check your steering column. There is a switch that cancels the turn signals in there. If it's bad, your signals will act funny and this also affects the hazard switch. Banging on the dash is what triggers the signals to work as the vibration goes into the steering column also. You might also want to check the fuses, relay switch, located inside the the left fender next to the steering column. Sometimes, the radio and the turn signals will go funky at the same time. Make sure your radio is grounded.
    Hope this helps.
    Cheryl
    1990 Dodge Daytona 2.5 ltr. Automatic

    Nov 27, 2009 | 1990 Dodge Daytona

    2 Answers

    1993 Dodge Shadow...left turn signal won't flash


    If the fuses are good and the front and rear bulbs are good, change the flasher for the turn signals, even tho the right is working. If that doesn't fix the problem, it might be in the turn sgnal switch on the steering column.
    If both bulbs are good for the backup lights and fuses are good, then the backup light switch, which is screwed into the side of the transmission has to bad.

    Apr 12, 2009 | 1993 Dodge Shadow

    3 Answers

    1997 dodge avenger turn signal probs and location


    replace the turn signal switch it self, mine did the same thing with the left turn signal, put in fuse and it will continue to flash... went to junk yard pulled one out of a 97 avenger just like mine, swapped them out and now it works fine. looked to be like some corrosion... to repace: 3 screws under columb, 2 screws on side of signal switch (black plastic side). unplug and replace

    Mar 20, 2009 | 1997 Dodge Avenger

    1 Answer

    91 toyota corolla left turn signal stays lit up al the time. Right turn signal working okay. Bulbs for left ok. where is the turn signal flasher located for this model or is it not the flasher,s problem....


    If the right side signals are working properly and you can hear the signal flasher clicking when the right side signals are selected, the flasher is not the problem. Its more likely you have a short to ground in the left side wiring somewhere.

    Feb 21, 2009 | 1990 Toyota Tercel

    1 Answer

    No brake lights of blinkers 1990 dodge dynasty


    While not likely, it is possible that the light bulbs in both sides are have bad filaments. Turn on ignition key (but don't start engine). Then turn on parking lamps (first detent or "click" on headlamp switch). Walk around car and look for illumination on front parking lamps and rear tail lights. Turn on the right turn signal. Are those (right hand) lamps now changing brilliance? Try the left turn signal in the same manner. Are those (left hand) front and rear lights changing briiliance? Take note of any positions that did NOT change briliance when the turn signals were activated. If NONE changed briliance, you either have a bunch of bad bulbs (unlikely) or a bad flasher (more likely) or a bad turn signal switch (most likely) or perhaps wiring problems (possible if the car has been in a collision or has been "worked on" by some "non-expert" mechanic). Check the action of the emergency flasher control switch located on the steering column (facing up). Pushing it in (down) should result in the button going to two different heights alternately (low, high, low, high). You could just have bad flashers or corroded flasher contacts! Good luck!

    Nov 15, 2008 | 1993 Dodge Dynasty

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    52 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Dodge Experts

    yadayada
    yadayada

    Level 3 Expert

    76630 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8516 Answers

    Are you a Dodge Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...