Question about 2004 Jeep Grand Cherokee

2 Answers

Signal light fuse keeps burning. How do i fix? Or what could be the problem.

Posted by on


2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Master
  • 473 Answers

Issue with Wirering System Chek for Broken Wire in one off your Signal light Also Chek Relay Connector

Posted on Oct 07, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert who has answered 20 questions.


    An expert that has over 10 points.

  • Expert
  • 48 Answers

Pull out signal lights and look for naked wires that may be grounding out if you find one use black tape or cut splice together , solder, and heat srink them back together,If you dont find any check switch that turns lights on. sometimes they get hot and melt and have to be replaced.

Posted on Oct 07, 2010


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 18 Answers

SOURCE: i have a 2004 jeep

a wire has to be shorting out the fuse, check all wires and make sure no metal is showing or frayed. If so wrap the wire that is showing with electrical tape to make sure no metal is touching any other wire, this would cause the short, and would pop the fuse. You may want to try a fuse with a higher breaking point as well, i.e. a 20 amp fuse.

Posted on May 05, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What could be causing the front axillary fuse to keep blowing? Even bigger fuses blow.

fuses blow from over current( dead short) they are rated at lower than what is required so that the wire doesn't burn
If you keep putting in bigger fuses without fixing the dead short, eventually the wire will melt the plastic insulation off and the vehicle will burn

Apr 29, 2016 | 2005 Buick Rendezvous

1 Answer

Signal light wiring

What did the dealer say? (QUESTION? do both the front & back (R) side lights burnout or just the front or the back light is burning out?) - 1. check for corrosion in both the front and back (R) side directional lights sockets. 2. Check to see that the fuse is the correct size, if a 20amp fuse is installed when it should be a 10amp fuse the lights could get a intermittent electrical spike that is burning out the light instead of the fuse. This doesn't help the problem, but it would tell you the problem isn't between the fuse wiring to the light. 3. One last thing I can think of is: some lights ground themselves when you reattach the plug to the chasse. NOTE: not all lights work this way, some other work just the opposite and have a fabric-washer around the top of the plug to keep them from grounding. Confirm what kind you should have as a precaution.

Sorry I couldn't be more helpful. Good Luck

Oct 06, 2013 | 2007 Kia Sedona LX Minivan

1 Answer

How to fix the signals

first check signal lights fuses if none of signal lights work.if fuse okay,check for burn out bulbs.if all is good turn signal switch is bad or you have loose wire to signal switch if your turn signal lights work some times.

Nov 26, 2011 | 1985 Mercedes-Benz 190

1 Answer

I have a 2004 jeep liberty my turning signal fuse keeps burning out, but my hazard lights work. Once my fuse burns out, I have no left or right turning signals.

a wire has to be shorting out the fuse, check all wires and make sure no metal is showing or frayed. If so wrap the wire that is showing with electrical tape to make sure no metal is touching any other wire, this would cause the short, and would pop the fuse. You may want to try a fuse with a higher breaking point as well, i.e. a 20 amp fuse.

May 05, 2011 | Jeep Liberty Cars & Trucks

1 Answer

My signal lights dont work i check the fuse it keep breaking so i must have a short some where

check the line (wiring) from the bulb socket through the fuse box. there must be a burned wire hitting another it happened to me once

or the fuse socket itself might be loose. doesnt have much spring to snug the fuse terminal

May 03, 2011 | 1986 Honda Civic

1 Answer

2006 f150 keeps blowing turn signal fuse

It sounds like the fuse is doing what it is supposed to do, and burning out when there is a short circuit. Check the wiring from the fuse block back to the lights and pay special attention to the trailer connection.

Oct 09, 2009 | 2006 Ford F-150

1 Answer

2002 dodge neon keep burning fuses in panel illumination. I replace it but it will and burn out while I'm driving and the driverside taillight turn signal wont work even after it is replaced. P.S Please...

You have a short in the circuit that leads to your dash lights. This is a potentially dangerous situation for which you fuses are doing their job. Do not be tempted to put a higher rated fuse in order to keep them from burning out. Instead, you must diagnose the source of the short and fix it.

Doing anything else may cause a serious short-circuit which might even lead to an electrical fire. If you are not confident in your own ability to find the short, please take the car to a mechanic to do the work.

I hope this helps.

Aug 02, 2009 | 2003 Dodge Neon

3 Answers

Blinkers not working

Did you check the bulbs? If one bulb is burned out, the blinkers won't word on that side. You could have one bulb burned out on each side. Start the car, put left signal on. Check front and back lights. Is one light on but not blinking? If that's the case, the light that's not on at all is burned out and has broken the circuit so the good light stays on and won't blink. Check the other side. You also have a 'flasher' , actually 2. One for emergency flashers, one for the turn signals. It could be that the turn signal flasher is shot. You just have to unplug it to remove. It's probably located near the fuses. good luck countrycurt0

Aug 10, 2008 | 1999 Jeep Grand Cherokee

1 Answer

1998 wrangler turn signal/brake light short

your socket may not be grounded properly, I have seen this before, and the simplest way to fix is change the socket with a new one.Not another used one it may also be bad.

Jul 30, 2008 | 1988 Jeep Wrangler

Not finding what you are looking for?
2004 Jeep Grand Cherokee Logo

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides