The light on the dash cruise switch lights up when I press it on but the cruise instrument light won't light up nor will the cruise activate when I press the set switch on the steering wheel, however, when I press and hold any of the three switches on the sterring wheel and then press the dash switch to on the instrument cruise light starts blinking until I press the dash switch off but the cruise still doesn't activate.
Bad relay. They are to the right of the fuses (fuses inside the car). You can see the relays if you open the cover to the fuses (they are big blue cubes), but will need to remove a few screws to remove the panel to get to them. I can't remember which one it is, it might make a clicking noise when you try and turn on the cruise. Or you can swap "matching relays - compare diagram on top" and see what else stop working. I had to replace several, my dash when out, my cruise, and I think one is the fan that blows your ac and heat.
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need. Goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Since there is no throttle cable, there is no "cruise control" fuse. The fuses used are #7, 9,and 13 in the under hood fuse/relay box and #18 in the under dash fuse/relay box. The most common failure is a bad brake pedal switch. Does the cruise control main switch "on" light work when the switch is pressed? The gauge control module (instrument panel) and the PCM control the cruise control.
Try checking the small switch at the top of the brake pedal. There may be two one for brake lights and one for the cruise control. To ascertain what is what, pull one wire off and see if brake lights work. If not, then the other switch controls the cruise control disconnect and engage..I you have a DC test light check to see if power is on on both side of the switch with brake pedal up. If so, depress pedal and check power on the other side there should be none, if there is the switch is defective.
check cruise control fuse and check the brake lights see if brake light working because the brake light switch will deactivate cruise control when brakes is applied.if brake lights dont work either fuse blowed or switch bad.if all is good have vechicle code scan because cruise control control by PCM and vechicle speed sensor and thottle actuator control motor.
The cruise-controls have 2-buttons that must be activated before it gets the car going when you remove your foot off the gas-pedal.
The cruise button is essentailly a switch that turns 'on' the cruise servo-motor that tells the sytems that you wants to use it, so it gets ready.
There are other three switches on the right-side of the steering wheel namely: resume accel; cancel; set decel.
To get your car to cruise: you must steady your speed and foot on the gas-pedal. You cannot just press the switches and expect the car to cruise. It takes about two-to-three seconds for the system to respond to a set cruising speed.
How to do it: accelerate to a speed of about 30-mph. Press the 'cruise' button on the dash first. Next you press 'set decel' button. This will turn 'on' the cruise control light on the instrument panel. Then wait a second or three and you would feel the cruise engagement. Any touch on the brake pedal will slow down the car and turns the cruise off. The 'cancel' button turns off the cruise light on the instrument panel.
If you hit the brake-pedal at any time for any reason, and you would like to continue cruising again, simply press the 'resume accel' button.
The cruise system works in conjunction with the braking system of the car. So all major parts of the braking system must be in good condition, otherwise the cruise system could shut off itself.
First, your car must be in gear and driving approx more than 60 km an hour
Secondly, using the Cruise Stalk switch turn the Cruise on, the dash should now have a lit icon for cruise power (green).
Once you have the desired speed, gently press the button on the end of the cruise in to set your speed. Remove foot from throttle and confirm cruise is active. Another dash light should come on as well (orange)
Failing that, if it doesnt work the usual suspect like fuses and the brake pedal micro switch should be looked at...