Question about 1994 Ford Explorer Limited

1 Answer

Rear barring an seal replaced - 1994 Ford Explorer Limited

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,826 Answers

I'm not sure if this is the right part of your car but, are you talking about the rear seal on the engine for the crankshaft?

If so:

Rear Main Oil Seal REMOVAL & INSTALLATION Fig. 1: Rear main seal installation for the 2.3L and 2.5L engines rear barring an seal replaced - 85553306.gif
Fig. 2: Removing the rear main seal 85553307.gif
Fig. 3: Installing the rear main seal on the 2.9L engines
If the crankshaft rear oil seal replacement is the only operation being performed, it can be done in the vehicle as detailed in the following procedure. If the oil seal is being replaced in conjunction with a rear main bearing replacement, the engine must be removed from the vehicle and installed on a work stand.

  1. Remove the starter.
  2. Remove the transmission from the vehicle, following the procedures in Section 7.
  3. On a manual shift transmission, remove the pressure plate and cover assembly and the clutch disc following the procedure in Section 7.
  4. Remove the flywheel attaching bolts and remove the flywheel and engine rear cover plate.
  5. Use an awl to punch two holes in the crankshaft rear oil seal. Punch the holes on opposite sides of the crankshaft and just above the bearing cap to cylinder block split line. Install a sheet metal screw in each hole. Use two large screwdrivers or small pry bars and pry against both screws at the same time to remove the crankshaft rear oil seal. It may be necessary to place small blocks of wood against the cylinder block to provide a fulcrum point for the pry bars. Use caution throughout this procedure to avoid scratching or otherwise damaging the crankshaft oil seal surface. To install:
  6. Clean the oil seal recess in the cylinder block and main bearing cap.
  7. Clean, inspect and polish the rear oil seal rubbing surface on the crankshaft. Coat a new oil seal and the crankshaft with a light film of engine oil. Start the seal in the recess with the seal lip facing forward and install it with a seal driver. Keep the tool, T82L-6701-A (4-cyl. engines) or T72C-6165 (6-cyl. engine) straight with the centerline of the crankshaft and install the seal until the tool contacts the cylinder block surface. Remove the tool and inspect the seal to be sure it was not damaged during installation.
  8. Install the engine rear cover plate. Position the flywheel on the crankshaft flange. Coat the threads of the flywheel attaching bolts with oil-resistant sealer and install the bolts. Tighten the bolts in sequence across from each other to the specifications listed in the torque chart in this section.
  9. On a manual shift transmission, install the clutch disc and the pressure plate assembly following the procedure in Section 7.
  10. Install the transmission, following the procedure in Section 7.
prev.gif next.gif

Posted on Oct 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How difficult is it to replace the rear axle seal on a 2002 jeep cherokee


it depends on which rear axle you have. on the 198 you have to remove the rear drums and remove the four nuts that hold the axle and seal in; and on the 8 1/4 you have to take off the differential cover and the center pin so that you could remove the c-clips that hold the axle in place. I have procedures for both but I need to know which one you have. the 198 requires drilling and presswork, the 8 1/4 requires a pry bar and a hammer.

Mar 25, 2013 | Cars & Trucks

2 Answers

1993 Chevy w/t 1500 rear end is leaking by drive shaft


The rear end seal.first block the wheels,so truck does not roll away.remove drive shaft four bolts to do this.might have to a pry bar to seperate .then take a center punch and make a mark on the nut.then mark the yoke.with a mark.this is done,so when its put back together,you dont over tightn the crush spacer.then remove the yoke.have a pan under neath to catch any rear end oil.remove yoke,then remove seal.reinstall seal,and reverse the process.hope this helped brad

Sep 16, 2011 | 1993 Chevrolet C1500

1 Answer

Need to know how the rear main seals go on a 200 Dodge caraven 2.4


you have a lion by the tail but i will tell you how.

1 drain your oil completely

2 un bolt the oil pan there are a lot of small bolts in the oil pan

3 un bolt the rear main barring that is the one next to the transmission
when you get the barring down don't touch the barring with your hands
now look Ware you took the barring down from you will see the
rear main seal remove the old and install the new once that is done
you need to put the barring back in with the bolts snug them up now
you need a torque wrench the bolts need to be torqued down to
30 ft.lbs each make sure the motor is clean from the old gaskets
and the oil pan use (permatex)(black) on both sides of the gaskets
4 reinstall the oil pan fill with oil and start your engine let it run for 10
min and let the gasket setup

hope this helps you
bob

May 13, 2011 | Dodge Caravan Cars & Trucks

1 Answer

Left wheel shaking. How do you replace a rear wheel bearing on a 2001 VW Jetta


jack your car and block it
remove the tire
now look at the center of the drum and take the cap off the middle use a pair of chanel locks
once off you will see a cotter pin bend it strate and pull it out
now take the nut off once that is off its time to pull the drum off watch the barring will fall out
Ware you took the nut off
once the drum is in your hand lay it down and take a long screwdriver and push the back
barring out you will get a seal and barring drop out on the in side now is ware you want to look in side the hole in side you will see two shinny round races 1 in the front and 1 in the rear they
need to be knocked out you knock the rear out from the front
and the front out from the rear that is called barring and a race remember witch one is front
and witch one is rear all you need to do is clean them so you can read the numbers on the
barring and the race also clean the seal same thing you need the id numbers to match them

hope this helps you bob

May 01, 2011 | Volkswagen Jetta Cars & Trucks

1 Answer

What is a pinion seal verses a rear main differential seal?


PINION SEAL GO INSIDE THE ASSAMBBLY BOX, REAR MAIN DIFFERENTIAL SEAL OUTSIDE CLOSE TO DRIVE TRAIN BAR

Jan 26, 2011 | 1999 Lexus RX 300

1 Answer

Replace broken sway bar for a 1996 ford windstar


Section 04-01: Suspension and Wheel Hubs, Front 1996 Windstar Workshop Manual REMOVAL AND INSTALLATION Stabilizer Bar Removal
  1. Raise and support the vehicle. Refer to Section 00-02 .
  1. Support vehicle with hoist or safety stands behind front sub-frame (5C145).
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the 6 mm drive hole in the front stabilizer bar link ball stud, do not use an Allen wrench to break loose or tighten or final tighten the front stabilizer bar link-to-shock absorber nut.
    Using care not to damage the front stabilizer bar link ball stud seal, remove the RH and LH front stabilizer bar link-to-front shock absorber nut.




  1. Using care not to damage the front stabilizer ball link stud seal, remove the RH and LH front stabilizer bar link-to-front stabilizer bar nut.
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use extreme care not to damage the ball joint boot.
    With another set of support safety stands under front sub-frame, remove two rear sub-frame retaining bolts. Lower rear of the front sub-frame to obtain access to stabilizer bar brackets (5486).
  1. Remove front stabilizer bar bracket bolts, stabilizer bar brackets, stabilizer bar bracket insulators and front stabilizer bar (5482) as required.
Installation
  1. Clean front stabilizer bar to remove dirt and contamination in area of stabilizer bar bracket insulator installation position.
  1. Lubricate inside diameter of new stabilizer bar bracket insulator with Rubber Suspension Insulator Lube E25Y-19553-A meeting Ford specification ESF-M99B112-A or equivalent. Do not use any mineral or petroleum based lubricants as they will deteriorate the rubber stabilizer bar bracket insulators.
  1. Install new stabilizer bar bracket insulators onto front stabilizer bar and position them in approximate location.
  1. Install stabilizer bar bracket on stabilizer bar bracket insulators and install new bolts. Tighten to 55-63 Nm (40-46 lb-ft).
  1. Raise front sub-frame and install new front sub-frame-to-body retaining bolts. Tighten to 115-132 Nm (85-97 lb-ft).
  1. Install front stabilizer bar link (5K483) to front shock absorber. Use care not to damage link ball joint boot seal.
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the 6 mm drive hole in the front stabilizer bar link ball stud, do not use an Allen wrench to break loose or tighten or final tighten the front stabilizer bar link-to-shock absorber nut.
    Install a new front stabilizer bar link-to-shock absorber nut. Tighten to 90-100 Nm (66-74 lb-ft).

  2. 66a0f1a.gif

Apr 28, 2010 | 1996 Ford Windstar

1 Answer

Back window leaks


JUST look and see, when raining? really !

THE TOP REAR , Window fits to a abar that fits to a long bar,
when the rear door closes , it seals against this bar, and there is a seal.

if no seal then go to GM or Suzuki and ask for seals.

Mar 28, 2009 | 1995 Geo Tracker

2 Answers

How toreplace rear main seal in 92 F150 4.9 inline 6


One thing you may want to try especially if you don't have a heated garage is a bottle of Bar's leak rear main sealer. I had a leak big enough to cause my clutch to slip and it worked for me. I figure in the spring I'll replace the seal, maybe.

Oct 04, 2008 | 1992 Ford F150 SuperCab

1 Answer

Vent window repair.


To replace the window seal, you first have to remove the vent window assembly from the door. After it is removed, the nut and spring on the bottom of the window has to be removed. Then remove the glass and frame from the vent assembly frame. Then gently remove the rubber off of the frame and install the new one after you replace the top vent bar seals. Reverse the window removal procedures to reinstall the glass and frame. The top vent bar seals requires a special tool to remove and replace the rivets you get with the replacement seal. You need to replace the top vent bar seal before reinstalling the new vent window rubber. When I replaced my top vent seals, it was fairly easy with my removal/installation tool.

Oct 03, 2008 | 1965 Ford Mustang

Not finding what you are looking for?
1994 Ford Explorer Limited Logo

626 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...