Question about 2001 Cadillac Eldorado
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: abs light/traction control light
You can check out what the trouble code is by pushing and holding the information button and the up arrow (right side of instrument cluster above the radio) until all the instrument clusters light. Press the information button (last) to enter test mode. I've had an error C1234, meaning Left rear wheel sensor fault. I found the problem to be a corroded connector under the chasis just under the rear left door about 2 feet in. I had to by-pass (replace 1 wire due to corrosion at the connector.
Posted on Sep 15, 2009
This refers to the suspension and steering, you probably have a faulty sensor somewhere.
One of the most common sensors to fail in this system is the steering wheel position sensor.
You need to run a diagnostic check to pull the trouble codes to pinpoint the faulty component.
How to pull the codes.....
Use the 3 switches located to the right (LH drive cars) of the Driver Information Center (DIC) to activate and respond to the OBD prompts on the DIC.
ON/OFF = YES
INFO RESET = NO
INFO DOWN or INFO UP = manual toggle
Ignition ON, acknowledge any warning messages;.
Press ON/OFF and INFO UP together for 2 to 3 seconds. Everything in front of you lights up for 4 or 5 seconds, then you will see:
Display shows "ALL?"
Answering YES will display "ALL CODES?"
Answering YES will run automatic test sequence and display codes, if any.
"ALL CLEAR CODES?" will display at the end of the automatic test. If you are satisfied you have the information you need, answer YES to clear/erase all error codes.
Answering "ALL?" with INFO DOWN will toggle systems test manually in order.
Answering "ALL?" with INFO UP will toggle system test manually in reverse order.
Press INFO RESET to reset DIC to "ALL?" to start again.
Ignition OFF to exit.
Write down the codes as they appear on the DIC, you may need to run the check again as it tends to scroll through quickly.
Report back here with the codes.
Posted on Sep 21, 2009
My Service Stability System Message along with the (ABS) Brake Light lit up on my dash, what can i do to fix it...Or what does this mean ?
Posted on May 07, 2010
Take a look at your air con controls on the centre console.
You will see an "OFF" button and to the right of this you will see a toggle switch with an up arrow with the word "PASS" just below it.
Simultaneously press the "OFF" button and the up arrow together for three seconds or so and release when you see the instrument cluster lights come on.
You are now in diagnostic mode.
Read the codes from the digital display on the instrument cluster.
Have a pen and note pad ready to write down the codes.
Posted on May 23, 2010
Tips for a great answer:
Jun 04, 2017 | Cadillac Cars & Trucks
Nov 27, 2015 | 2002 Cadillac Escalade Ext
Nov 22, 2012 | 2001 Cadillac DeVille
Whenever this warning or any other stays on in the dash it is indicating that the systems control module has detected a fault, it then disables the system as long as the light is on. You must now have the dealer hook up a special electronic diagnostic tool and "scan" the system for the fault code that is stored for the problem(s)
Sep 19, 2012 | 2000 Cadillac DeVille
Jan 31, 2011 | 1998 Cadillac DeVille
Oct 02, 2010 | 2002 Cadillac Escalade Ext
Mar 04, 2010 | 2002 Cadillac Deville
Mar 03, 2009 | 1989 Cadillac Eldorado
474 people viewed this question
Usually answered in minutes!