Question about 2005 Isuzu Ascender

1 Answer

Low beam lights went out.... All fuses and bulbs are ok, what could be the issue

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Isuzu Master
  • 8,210 Answers

Headlight relay.

Please see my tip at http://www.fixya.com/cars/r6053280-lights_out_lights_not_out_bulbs_ok . These are generic instructions. If you get stuck or need specific instructions for your car, please get back to me with model, year and engine info.

Posted on Oct 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

High beams work for both lights, 1 low beam does not


Check for power with a test light with the light connected. If you have power then its the ground. If no power then you will need to trace the wire back to find break. As I recall they did have seperate fuse for left and right headlight high & low beam. Also did you get a defective new bulb?

May 31, 2015 | 2006 Mazda Tribute

1 Answer

Main beam lights not working


It's possible the "main" lights elements have burnt out.
I believe it's a single bulb per side with both high and low beam elements inside.
Try replacing a bulb and see what that does.

Mar 15, 2014 | 2007 Ford Fiesta 1.4

4 Answers

I have a 2006 civic SI. DRL indicator is on, driver side low and high beam ok. Passenger side low beam ok but DRL and hi beam not working. Any help is appreciated.


When either the high or low beam light is out in either side, DRL (daytime running lights) indicator will come on. When one bulb goes out, that's a clue the opposite bulb will burn out soon, so its best to replace both bulbs. If it was a fuse issue, both left and right side would be out. If driver side is OK but passenger side is not, then its a bulb issue. A 2006 Honda civic takes 9006 (HB4) low beam bulbs and 9005 (HB3) high beam bulbs. Cheapest is online from Walmart site-2-store. After procuring, wear latex, vinyl, or ANY gloves to keep your (corrosive) oil skin from coming in contact with headlight glass bulbs. Your skin oil will chemically react and cause shorter life span on glass bulbs. Instruction don't tell you this, so you handle with your hands, then need to replace bulbs 3 years later instead of 5 years (or more) in the future. With gloves on, pop the hood and look behind each headlight. Turn counter clockwise to unlock headlight bulb holders. Its a quarter to half turn to unlock bulb holder lock. Replace one bulb at a time so you don't confuse high beam from low beam. The wire has a tab you need to lift to pull out & disconnect wire connector. You might need a slim narrow-**** (NOT phillips) screwdriver to lift the tab; or use your house key. Snap the wire connector to the new bulb, then twist into headlight housing to secure bulb holders, then move on to the next bulb to repeat the procedure. Pict below, 9005 high beam is on the left, 9006 low beam is on the right. Handle by grasping the plastic base, not the glass bulbs. The raised potrusion on the bottom center is where the tab locks onto wire connector. Replace all 4 bulbs now, but in the future, its likely the low beam will wear out before the high beam. In the future, replace only the pair, not all 4. The factory installs inferior bulbs that go out sooner, hoping you'll take to dealership and they ******** you with higher parts-n-labor fees. As opposed to Walmart online site-2-store, it would cost you AT LEAST triple in parts & labor from dealership to replace all 4 headlight bulbs :-(
45d1f6ac-2983-42b9-a46c-30ef441b89e7.jpg

Nov 29, 2013 | 2006 Honda Civic

1 Answer

Fuse diagram


Have you checked to see if you have power at the headlight bulbs ? And have you tried replacing one of the bulbs ?

Jul 07, 2013 | 2001 Ford Focus

1 Answer

Where is fuses for headlights located for 1991 Honda LX


Hello Jeff, I've seen this before, a while back on a Pontiac Sunbird. A friend called me with the same issue as you. I did come checking of (looking for low resistance using a ohm meter) the low-beam elements, both were open (no resistance, which comes from the little spiral wire just like a regular light bulb). This is what I believe happened to you. One headlight went out previously but still having one that worked you didn't really notice. You did notice however when the last and only low-beam filament went out and this lead you to believe (as did my friend) that both went out together. You probably need to change both bulbs. Check first each low-beam, unplugged of course with a ohm meter to confirm. I favor those bluish bulbs, got mine at Pep Boys (Pilot brand?). You can see better with those in my honest opinion.

Dec 30, 2011 | 1991 Honda Accord

1 Answer

Low beams dont turn on........... bulbs check ok...................fuses under hood ok.............need help


{: ) I wonder how you checked the fuses and the bulbs. Did you check also the HDM fuse 15amp and the HDM relay both at the underhood fuseblock? Turn on the low beam and check for 12v at the LO beam fuses. If there is voltage at the fuses but the low beam ok bulbs won't light, then there's a wiring issue from your fuseblock going to the bulbs.
But if no voltages on the LO fuses when the low beam is switched on, then the problem could be on the HDM fuse or relay, the headlamp switch, the BCM, or even the fuseblock.

Jul 02, 2011 | 2006 GMC Envoy

1 Answer

How to change the low beam bulb on driver and passenger sides


the low beam bulb is one with the high beam ,so you need to replace the headlight bulbs, its hard to believe they both went at the same time,i would buy one and replace it if lights still don't work than you might have other issues like maybe a blown fuse.

Jan 27, 2010 | 2005 Nissan Altima

1 Answer

Both low beam lights went out... hi beams are ok. is there a seperate fuse for the low beams?


there are seperate fuses however did you check the bulbs. they could just need replacing. there will be fuses for left and right. should be under the hood.

Dec 24, 2009 | 2004 Hyundai Tiburon

1 Answer

2005 Chevy Impala Headlight


hi from uk for info the dip beams have a seperate fuse in fuse box for each side offside and nearside so if bulb is ok ? check fuses if you have h/book ? it will give location and amperage of fuse required also the same goes for the side/tail licence plate lights are on seperate fuses so you do not lose all lights if fuse goes

Jan 02, 2009 | 2005 Chevrolet Impala

Not finding what you are looking for?
2005 Isuzu Ascender Logo

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...