Question about 1988 Oldsmobile Delta 88

1 Answer

I want to know if a crankcase sensor has anything to do with spark

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 326 Answers

Crankshaft position sensor definetly affects spark if bad no spark

Posted on Oct 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my 1997/98 Toyota corolla 1600 twin cam ruby red collection won't start?


Is fuel reaching the cylinders? Check for weak spark and try a new igniter? Crankcase sensor operative? Compression? Air?

Aug 21, 2016 | 1998 Toyota Corolla

2 Answers

No ignition spark when hot


problem in the ignition control module or coil
replace the coil with a suitable voltage rating( some are straight 12 volts and some are 12 volts start 7.5 volts run
it is an overheating electronic component that is causing the fault

May 15, 2016 | Cars & Trucks

2 Answers

I have a 1999 Mitsubishi Galant and need to know how to put on a valve cover gasket. Oil is leaking out and dripping and it's causing it to burn and smoke comes out of the car.


Instructions
    • 1 Allow the car to cool. Disconnect the battery terminal. Remove the right side vent screen top extension. Disconnect the ignition coil with power transistor and its wiring and brackets.
    • 2 Disconnect the left hand side coil wires and spark plug wires. Remove the spark plug wires, valve cover bolts and the valve cover. Unplug the electrical connections from the intake manifold runner control actuator. Unfasten the actuator retaining the screws, right bank heated oxygen sensor front and rear.
    • 3 Remove the heated positive crankcase ventilation (PCV) valve. Remove the heated oxygen sensor plug and the Differential Pressure Feedback EGR (DPFE) sensor. Disconnect the ignition coil with power transistor and its wiring and bracket. Remove the valve cover bolts, the valve cover and the old valve cover gasket. Clean the valve cover seating area with automotive engine cleaner and place the new gasket in the gasket seating area.
    • 4 Replace the parts that were removed and disconnected by reversing the steps. Replace the valve cover gasket and tighten the bolts, in sequence, ensuring not to over tighten. Put back the ignition coil with power transistor and its wiring and bracket, the heated positive crankcase ventilation (PCV) valve, the heated oxygen sensor plug and the Differential Pressure Feedback EGR (DPFE) sensor.
    • 5 Add oil to the car. Start the car and let it run at idle for a while to check for leaks..

Aug 18, 2011 | 1999 Mitsubishi Galant

1 Answer

I needto know how to replace a Crankshaft postion sensor A circuit


      • The sensor is mounted in a fixed position in the engine block. The tip of the sensor protrudes into the crankcase at a distance of 0.05 plus or minus 0.02 inch from the crankshaft.
      • A crankshaft adjusting tool may be used to check these rings
      place the tool on the pulley extension surface and rotate the tool around the pulley.
    • If any blade touches the tool, replace the pulley.
  • Inspect the trigger wheel behind the crankshaft pulley and the sensor for damage.
  • If the engine misfires all the time or on acceleration only, test the following components:
    • Engine compression.
    • Spark plugs.
    • Spark plug wires.
    • Ignition coils test for firing voltage with a test spark plug.
    • Crankshaft sensor.
    • Fuel injectors on multiport and sequential fuel injection systems. To remove the crank sensor
  • Disconnect the wiring harness.
  • Unbolt the sensor mounting bolt.
If the crankshaft timing sensor or the camshaft reference sensor is removed, follow this procedure when the sensor is replaced:
  • Thoroughly clean the sensor tip and install a new spacer on the sensor tip. New sensors should be supplied with the spacer installed.
fr_24.15.gifSpacer on crankshaft timing sensor and camshaft position sensor.
  • Install the sensor until the spacer lightly touches the sensor ring, and tighten the sensor mounting bolt 105 in.lb.
hope this was what you needed.....

Jun 03, 2010 | 2000 Saturn Ls 4dr Sedan

1 Answer

Shakes while idling and sometimes stalls.


check for minor vacuum leak and map sensor,pcv,egr valve

Oct 13, 2009 | 2001 Chevrolet Blazer

1 Answer

Jeep turns over but won't start.Replaced very worn plugs. Suspect the crankcase sensor.


It takes spark, fuel, and air to run.Is there spark? would need more info...

Jul 23, 2009 | 1996 Jeep Cherokee Country

2 Answers

My 02 dodge 5.9 v8 engine turns but wont start


check to see if camsensor working and the asd relay.need a scanner to check .

Jun 01, 2009 | Dodge Cargo Cars & Trucks

4 Answers

Where is a knock sensor for 1998 Mercury Villager located?


Here is a image of it's location, I hope it helps.
8262b2e.jpg

May 18, 2009 | 1998 Mercury Villager

1 Answer

1995 lincoln continental wont start


have you checked out the core packs? and if you go to autozone you can get a printed diagram where the crankcase sensor is located also look for the location normally under the hood for the fuel pump relay

Jan 15, 2009 | 1995 Lincoln Continental

2 Answers

No spark to plugs dont starte


then its a problem with your electrical system, possibly your distributor or the wiring inbetween.

Oct 20, 2008 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?

Open Questions:

See all 1988 Oldsmobile Delta 88 Questions

Cars & Trucks Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...