Question about 2006 Kia Rio

1 Answer

If you disconnect your crankshaft positon sensor will the engine still start.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Kia Master
  • 75,051 Answers

No it will not start.

Posted on Oct 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can you tell me where a crankshaft positon sensor is on a 2010 Dodge Journey 2WD 2.4 liter engine


Most of the crank shaft sensor are located behind the main pulley or crank pulley just follow the wire when u open up the timing cover

Feb 03, 2015 | Dodge Cars & Trucks

1 Answer

I have a 2003 Chevy 3500 dully and driving home my


What motor?? If it is gas burner I would start with Crankshaft positon sensor.

Sep 11, 2014 | Cars & Trucks

1 Answer

Crankshaft sensor on a 2000nissan xterra where is it located and how can it be replaced


crankshaft position sensor location for 3.3 V6 engine is mounted at the rear of the engine on transmission bellhousing, the 3.5 V6 engine crankshaft sensor located at front of the engine on the aluminum oil pan section below crankshaft pulley.replace the crankshaft position sensor remove heat shield disconnect the electrical connector the remove sensor retaining bolt then remove crankshaft sensor.after replacing crankshaft sensor you need to erase code if check light come back on.

Nov 14, 2011 | 2000 Nissan Xterra

1 Answer

Be driving car cuts off but will start back up


well sounds like a crankshaft postion sensor or camshaft positon sensor both tell the cpu when to fire spark

May 05, 2011 | 1995 Buick LeSabre

1 Answer

Where is the crankshaft position/crank angle sensor located on a 2005 kia sedona


Hi, at the front of the crankshaft. if its near time for the timing belt, you want to replace it along with any pullies, tensioner and water pump


The crankshaft position sensor is mounted on the engine near the crankshaft.

Operation

The crankshaft position sensor is a Hall-Effect sensor that senses the crank angle (piston position) of each cylinder and converts it into a pulse signal. The signal from the sensor is relayed to the ECM to indicate engine rpm and the position of the crankshaft.

Removal & Installation

  1. Disconnect the negative battery cable.
  2. Disconnect the connector from the sensor.
  3. Remove the bolt that retains the sensor in place.
  4. Remove the sensor from its mounting. To install:
    1. Installation is the reverse of the removal procedure.
    2. Clearance between the sensor and the sensor wheel should be 0.020-0.059 inch. 2002-2005
      1. Properly connect the scan tool.
      2. Start the engine and allow it to idle.
      3. Be sure the idle position switch is ON.
      4. Specifications are as follows:

        Temperature - 4°F, test specification 1500-1700 RPM Temperature 32°F, test specification 1350-1550 RPM Temperature 68°F, test specification 1200-1400 RPMTemperature 104°F, test specification 1000-1200 RPM Temperature 176°F, test specification 650-850 RPM

Mar 16, 2011 | 2003 Kia Sedona

1 Answer

Where's the cranck sensor located?


Click the boxes with a red x in them to see diagram images. 5VZ-FE Engine
  1. Disconnect the crankshaft position sensor harness. Fig. 1: Exploded view of the crankshaft position sensor mounting 86824pa8.gif

  2. Remove the bolt retaining the sensor to the vehicle.
  3. To install, attach the sensor to the vehicle, tighten to 69 inch lbs. (8 Nm).
2VZ-FE and 3VZ-FE Engines
  1. Remove the engine under cover.
  2. Remove the alternator.
  3. Unbolt the alternator bracket.
  4. Disconnect the crankshaft position sensor harness.
  5. Remove the bolts securing the sensor and the sensor. Discard the O-ring.
  6. When installing, apply a light coat of engine oil on the O-ring, install on the sensor tighten the bolts to 74 inch lbs. (9 Nm).
1FZ-FE Engine
  1. Remove the engine under cover.
  2. Unbolt the sensor protector. Fig. 2: Exploded view of the 1FZ-FE crankshaft position sensor mounting 86824pb3.gif

  3. Disconnect the crankshaft position sensor bracket and harness.
  4. Remove the bolt, nuts and sensor.
  5. When installing, attach the sensor and tighten the bolt to 14 ft. lbs. (20 Nm) and the nuts to 78 inch lbs. (9 Nm).

Jan 28, 2011 | 1989 Toyota 4Runner

1 Answer

Vehicle doesn't start sometimes


If the car just tries to start an start but wont it could be a crankshaft positioning sensor or camshaft positoning sensor.Or you could have a
loose wire.

Jan 13, 2010 | 1994 Honda Accord

1 Answer

Ignition problem


If there is no spark in any cylinder. Then check crankshaft positon sensor which is is in engine block. Wires from here lead to module and coil packs.

Sep 09, 2009 | 1992 Suzuki Sidekick

1 Answer

Where crank shaft and camshaft?


The camshaft position sensor is located on the timing cover, near the top of the motor. The crankshaft position sensor is located on the same timing cover near the crankshaft. Just a side note, more than likely the crankshaft position is your issue and it's under a recall from Nissan and they will replace it for free.

May 23, 2009 | 2002 Nissan Altima

1 Answer

2002 pt cruiser Camshaft Sensor


change the crankshaft positon sensor in the rear of the engine above the oilfilter. Also check the wiring to this sensor, they have a problem shorting out. You have to change the camshaft and crankshaft sensors at the same time. Make sure you give your car a major tune up. Did you check yor starter?.........runjoe

Feb 04, 2009 | 2002 Chrysler PT Cruiser

Not finding what you are looking for?
2006 Kia Rio Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...