Question about Chevrolet Impala

1 Answer

How do I replace the rear driver turn signal bulb on a 2006 chevrolet impala?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 198 Answers

You have to take the covering in the trunk loose to get to the light sockets, they should turn left or right to remove, then don't touch the new bulb with your fingers as the acid on you skin wll make it go out faster than normal. the new bulbs should be flat socket type that snap in and out, use plenty of bulb grease when replacing all bulbs, helps with corrosion and water sealing.

Posted on Oct 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Rear right turn signal does not work. Bulb is ok. Flashes rapidly on the dash when I put the right turn signal on, ideas?


the flasher unit is out ..needs replaced i believe it is part of the hazard switch on those cars

May 26, 2015 | 2006 Chevrolet Impala

2 Answers

07 Impala rear driver side brake light and turn signal does not work, but when I checked the bulb it was working just not when I press the brake. The left turn signal on the dash also blinks rapidly.


Sounds like a possible bad ground connection.
Make sure the contacts for the bulb are clean.
Make sure the cround connection is not corroded.

May 21, 2015 | 2007 Chevrolet Impala

1 Answer

Where do i find and how do i replace the turn signal relay switch on a 2006 chevy colorado


ARE YOU SURE THAT YOU USED THE RIGHT BULBS? IF REARS WORK AND FLASH RAPIDLY THE RELAY IS WORKING. A RAPID FLASH IS CAUSED BY A BAD BULB OR WIRING

Dec 18, 2014 | 2006 Chevrolet Colorado

2 Answers

2007 chevy impala brake light and left turn signal not working


Fast flashing dash signals mean there is a bulb issue-DEFINATELY!

Aug 07, 2012 | 2007 Chevrolet Impala LS Sedan New Cars

2 Answers

The turn singnals don't flash on my 2004 chevy impala


It's time to replace the flasher relay.The signal flasher is located under the dash near the steering column.Also check for the indicator bulb.Replace them if damaged.
Front Turn Signal Light Bulb Size: 3457ALL
Rear Turn Signal Light Bulb Size: 3057
Hope this helps.Your valuable feedback would be appreciated.Thanks

Jun 11, 2011 | 2004 Chevrolet Impala

3 Answers

Rapid right turn signal on dash but no right rear turn ligt at all


What that rapid turn signal on the dash means is, the rear turn signal tail light is burnt out. This is how you know the bulb is bad. Replace the burnt out tail light bulb and you will be back to normal.

Jan 16, 2011 | 2008 Chevrolet Impala

1 Answer

2006 pt cruiser on drivers side rear turn signal


The turn signals flash depends on each and every bulb working correctly. When one bulb fails, you will notice a change in the flash frequency, as you describe.

Replace or repair the bulb that is not working, and you should be good to go.

Doc

Sep 14, 2009 | 2006 Chrysler PT Cruiser

2 Answers

Right front turn signal not working at all right rear flashes fast? 2004 Impala


Sounds like your front turn bulb burnt out. When the turn signal operates fewer bulbs it works faster. You need to change the right front bulb.

Aug 09, 2009 | 2004 Chevrolet Impala

1 Answer

2006 Chev Impala turn signals not working on rear lights, turn signal flashing at a faster rate than normal, No brake lights when pushing on brakes.


Two issues here, you will need to replace the flasher. this will correct the erratic turn signals.

Concerning the brake light. Make sure the bulbs are in working condition and, check the wiring harness for faults as well. if the bulbs and wires arr OK, replace the brake light switch.

You can test for proper current by pulling the brake light bulbs out the socket and, use the copper prongs inside the brake light socket for testing. use a volt meter and, hit the brake pedal and, see if the meter registers a current. if not, replace the wiring harness.

Jun 04, 2009 | 2006 Chevrolet Impala

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...