Question about 2007 GMC Sierra 3500HD

Open Question

I have to replace the rear axle seal on a 3500HD 2007 GMC. Is there any hints or tips you could share with me Thank You

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Rear Axle Removal

if you are talking about the axle seals, 1.REMOVE THE WHEELS.2. REMOVE THE DIFF COVER(slowly)3.REMOVE THE BRAKE CALIPER ASSEMBLY.4.REMOVE THE 8MM PIN IN THE DIFF CARRIER. 5.TURN CARRIER AND REMOVE THE LARGE PIN.6. FIRMLY HIT IN THE AXLE, A SMALL RETAINING C CLIP WILL FALL INTO THE DIFF HOUSING. DO THE SAME WITH THE OTHER SIDE. ( be careful if you have rear speed sensors remove it when you remove the brake calipers . you will break it when you are pushing in the axles.)7.pull axles and replace seals

Posted on May 30, 2008

warlock61
  • 659 Answers

SOURCE: rear axle seal replacement 1994 ford bronco

It is fairly easy to do. remove rear wheels and brake drums, remove the differential cover, rotate the diff to access the diff pin bolt and remove, remove pin, push axles inward and remove c clips, slide out axles and replace seals. reverse procedure

Posted on Dec 29, 2008

MrScary66613
  • 1990 Answers

SOURCE: Rear axle seal leaking on 1997 GMC Yukon 4x4

You are Talking about the Main Cover on the Rear of the Rear end Correct???? If so, This is Just a Gasket and is Very easy to replace. The Gasket is Simply Worn out.

Posted on Jan 17, 2009

  • 52 Answers

SOURCE: Rear Axle Seal Replacement

remove rear tires, then remove brake calipers and rotors, then remove the 4 nuts (each side) that hold the axle shafts to the axle tube (located around the axle tube behind the backing plate) then using a slide hammer pull the axle shafts out, next using a die grinder and an air hammer get he retainer collar and the bearing off (without damaging the axle shaft) then remove the seal and the outer race which will still be in the housing. next put it all back together, make sure the plate with the studs is still on then slide the seal, bearing, then retainer on (all new parts) and using a press push them all the way back on. then is simple reassembly.

Posted on Apr 22, 2009

  • 335 Answers

SOURCE: REAR AXLE SEAL LEAKING ONTO BRAKE SHOES NEED INSTRUCTIONS ON HOW TO FIX

Jack up vehicle and support on stands. Remove wheels. Remove differential cover . Locate and remove lock pin that holds cross shaft in. Slide cross shaft out. Push axle inward to release axle c clip. Remove axle and pry out old seal. Install new seal with proper tool.Add some lube to the seal lip to aid axle intallation. Revese removal procedure. This is for a "c" type axle.
Another type has 4 nuts attaching a retainer plate to the backing plate behind the axle flange. In this case the 4 nuts are removed and the axle will come out. This may require a little effort. I think that you have a "c" type axle in your vehicle. Hope this helps. Moe

Posted on Apr 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove a 1990 rear axle on a Chevy pickup four wheel drive


Diane, links below show how to remove axles on Chevy trucks.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
remove rear axel on 1993 chevy g20
How To Change Your Rear Axel Seal Chevy Silverado
How To install Replace rear Axle 2000 06 Chevy Suburban Silverado GMC...


May 05, 2016 | Cars & Trucks

1 Answer

Have gear oil leaks under transmission in two holes next where the axel meets on each side


Keith the seals will need replaced, take into a shop and have a tech give estimate for repair. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
half shaft seal replacement Google Search
How To Install Replace Front CV Axle Shaft 2002 09 GMC Envoy and XL XUV
Part 1 How To Replace Front Axle Shaft Seal RH Front Chevy GMC
CV axle replacement Subaru Outback 2000 Legacy Forester Install Remove...


May 04, 2016 | Cars & Trucks

1 Answer

2005 GMC 4x4 HD 2500 6.0 eng. rear axel seal


SEAL COULD BE LEAKING CAUSE YOU DIDNT LUBRICATE THE SEAL LIPS WITH PETROLEUM JELLY TO HELP THE THE SEAL LIP SEAL OR YOU DAMAGE THE SEAL WHILE DRIVING IT IN.AXLE FLANGE NUTS TORQUE IS 58 FT LBS THE AXLE HUB NUT TORQUE IS 177 FT LBS.

Jul 14, 2010 | 2005 GMC Sierra 2500HD 4WD

1 Answer

Rear Wheel Seal & Bearing on 1999 GMC Safari Van


Yes you do have to pull the axle and make sure you put everything back in the same place you removed it from. The ring and pinion shouldn't have to be bothered. You will have to remove the rear end cover to remove the axle. Its very easy to do. There is a pin inside the rear end that has to be removed to pull the axle. Pay attention to how you take it out and put it back the same way. It sounds as if you can do this with no problem.

Apr 11, 2010 | 2000 GMC Safari

1 Answer

Need detailed manual or assistance in replacing left rear axle seal and bearing on 2005 GMC Sierra pickup with 5.3L engine and a 324 rear end


You'll need to remove the rear end cover, remove the pin in the center pumpkin, push axle toward the center of vehicle and remove the axle clip, pull out axle. You may need a bearing puller to remove bearing.

Mar 04, 2010 | 2005 GMC Sierra

1 Answer

How do I remove the rear axle to replace the seal 1996 jimmy


You will have to remove the differential cover on the rear end, in the center of the gear cluster you'll have to rotate your axle until it exposes the ends of the axle shafts, push in the axles as far as you can from the brake pad assembly area, then, there this a C clips that slips into a groove on the end of the axle, you'll have to reove the C clip to pull out the axle.

Apr 25, 2009 | 1996 GMC Jimmy

1 Answer

Spindle nut on rear axle


Every time I've done it I just use a drift and a hammer as its not that tight, as soon as it turns some it spinns with your fingers

Feb 25, 2009 | 2007 Chevrolet Silverado 3500HD New Cars

1 Answer

Rear axle seal leaking on 1997 GMC Yukon 4x4


You are Talking about the Main Cover on the Rear of the Rear end Correct???? If so, This is Just a Gasket and is Very easy to replace. The Gasket is Simply Worn out.

Jan 17, 2009 | 1997 GMC Yukon

2 Answers

Rear Axle Leak


if it is the seal, you will have to remove the caliper and rotor, remove the differential cover and remove the bolt and pin inside the diff carrier housing. push in the axle and remove the axle clip and pull out the axle use a seal puller or prybar to remove seal reverse the steps to assemble

Dec 10, 2008 | 2001 Lincoln Town Car

1 Answer

2000 gmc both rear tire oil leakage.


You are correct, it's not brake fluid. Check the level in your rear axle, it sounds like you have bad seals in the axles allowing the rear differential gear oil to leak inside the brake drums.
This is a heavy weight oil, 80 or 90 weight. This leakage will ruin your brake pads, and if enough leaks out, your rear differential will blow. The seals aren't expensive, but it's a lot of labor to pull everything apart to get at the seals, plus new rear brakes. My Ford ( and I'm sure your GMC) require removal of the rear axles to change the seals. Good Luck! countrycurt0

Sep 17, 2008 | 2000 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

421 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...