Question about 1992 Cadillac DeVille

2 Answers

How to change the battery the connections are on the side of the battery never changed this type theyre usually on top of the battery

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

Just remove the bolts with a 12 point socket or wrench. Just turn them counter-clockwise and they will come out

Posted on Oct 06, 2010

Testimonial: "i liked your advice 5/16 would have been more specific but all in all i did what you said and it worked thanks"

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 198 Answers

You can buy the replace ends for the side mount battery at Auto Zone, just cut and strip back the battery cable the length of the new fitting, clean the battery posts with a brush before putting on grease and bolting up new cable ends to battery after making cables with new ends on them. Use battery grease on each positive and negative end and then twist the cable before you insert it into the new fiitting, use the battery grease in between the new ends and the battery also. Make sure your battery has a full charge in it before re-installing it on your car, needs to have 13.6 Volts dc to keep charging system in good condition.

Posted on Oct 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Change battery 1998 Nissanpathfinder


Sounds like a couple of washers are missing from rhe adapter that takes up the additional space. Try to install a split type washer in their place, so you can tighten down better. Good luck.if the problem is the screw on the battery that should be permanent is spinning. Try securing the center threads while tightening"assuming theyre aide mount type" maybe with a pair of vice grips to hold the bolt in place while you tighten the nut.

Jan 04, 2018 | Cars & Trucks

1 Answer

Where is the transmission fluid temperature sensor on a 2007 Hyundai Getz 1.6 auto? I have been told theyre normally above the oil pan, thanks


It is on the top of the transmission. The transmission doesn't have a pan. You should be able to look down the side of the battery and see the sensor

Jan 01, 2015 | Hyundai Cars & Trucks

1 Answer

I need to change the battery


it depends if it is top post or side post, another words wheather the cables connect to the top or side of the battery. side post are usually 5/16 the top post are usually 1/2 make sure to remove the ground first so not to short anything out. good luck

Aug 10, 2012 | 2004 Pontiac Sunfire

2 Answers

How to change out a starter


Dis connect the battery, Locate it on the transmission, then dis connect the cables going to it, then loosen and take out the bolts holding it up. Piece of cake

Nov 23, 2010 | 1998 Chevrolet S-10 Pickup

1 Answer

How dos the positive battery cable attach


Hi Lacinat,

Top post type batteries employ clamp connections. Side mount types have disk like screw in connectors.

Typically, both positive and negative terminals have identical connections. Look to the negative connection as a model.

Common tools needed:
1/2" wrench for top mount

5/16 socket for side mount

That's about it.
Best regards,

Mike

Dec 08, 2009 | 2000 Dodge Caravan

1 Answer

How do I replace the CV joint boot on the wheel side?


either buy a split boot kit you can fit it while the shaft is as is in the car,or buy non split type boot and remove CV joint to change (more work)split boot kits are available at auto parts retailers.theyre also well priced

Oct 01, 2009 | 2003 Volkswagen Passat

1 Answer

I dont know how to change the dead battery on my 1990 Buick Lesabre. Its conections are on the side and im not sure how to get them off, or where to get another one with conections on the side and not the...


The connections unscrew just like any other bolt. There just on the side. Most auto supply stores carry these type of batteries. The thing to make sure you get right when purchasing the new battery is the cold cranking amps. Make sure these are correct for your car. The auto supply store should be able to set you up with the correct battery. Hope this helps

Jun 06, 2009 | 1990 Buick LeSabre

Not finding what you are looking for?
1992 Cadillac DeVille Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

80417 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...