Question about 2001 Chevrolet Impala

1 Answer

Not getting no power to the ignition or the coils cant figure it out

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Try to check and change the sensor under the drivers seat. I heard someone saying it worked for him

Posted on Oct 25, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

MY 92 OLDS 88 HAS NO SPARK.HAVE. HAVE POWER GOING TO ECM.HAS 3 COILS..FIGURE THEY ALL CANT GO OUT AT SAME TIME.REPLACED CRANKSHAFT POS. SENSOR AND HARMONIC BAL. 8 MONTHS BACK


Sounds like the ignition module or the crank sensor. Even though the crank sensor is fairly new doesn't mean anything. Remove the ignition module and take it to a parts store. Most parts stores can test it.

Jun 11, 2010 | 1992 Oldsmobile Eighty Eight

2 Answers

1990 chevy lumina apv - pickup coil -runs ok 15 mi & stalls


I'm assuming you have the distributor out? You will need to, as the shaft has a gear on the bottom end that has a roll pin. Make sure ALL is marked so that you re-assemble it the same way. You also need to mark the rotor position, and the base of the distributor so you can put it back where it was, or you will have to re-align and time everything!

Jul 10, 2009 | 1990 Chevrolet Lumina APV

1 Answer

Ignition coils not getting juice...


are u asking y it doesnt get 12 volts input or are u asking y it doesnt fire? if it is receiving voltage, but not firing,then u need to replace the coil pack,if it is not getting voltage to the coil,then if it is pluged into a module the module is bad and u need o replace module and coil pack

Jun 30, 2009 | 1991 Nissan 300ZX

1 Answer

Engine will not stay started


This can be caused by the electrical part of the ignition switch, not the key cylinder, the switches come apart and cause this loss of power to the ignition system, worth checking, the switch is near the base of the steering column, you will need to remove trim under steering wheel and then 2 nuts and drop the column down to get at switch for testing. here is a picture
476f0cc.jpg

Apr 01, 2009 | 1995 Ford Mustang

1 Answer

Restoring a 1953 ford truck v8 flathead 239 and cannot get fire to ignition switch, distributor or coil. I have tried everything. All wiring is new. have traced all of the wires. cannot figure it out. i...


you should have battery power going into ign switch. if you do not then your wiring from switch to battery is open somewhere. i cant pull a schematic on this but would assume it is not connecting thru a junction block trace this wire back to its source and find where you are losing power

Jan 29, 2009 | Ford F-100 Cars & Trucks

1 Answer

Ignition problems please help


do you hear your fuel pump go on when you turn key ? if not fuel pump relay may be bad

Jul 14, 2008 | 1993 Mercury Sable

Not finding what you are looking for?
2001 Chevrolet Impala Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...