Question about Ford Excursion

1 Answer

I have a 2000 ford excursion v10 and the fuel gauge has stopped working....

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 473 Answers

Check Along the Frame on the Driver Side Beside the Fuel Tank For Terminal Connector..Check For Bad Connection ...Possibility Corrosion inside Connection if not Check inside Fuel Tank For Potentiometer Gauge Level defect... and Fuse Box for Fuel Gauge fuse ..good luck

Posted on Oct 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Triton v10


Begin with the basics....
INSPECT COOLANT LEVEL,
Low ????,PRESSURE TEST SYSTEM,
PRESSURE TEST RADIATOR/EXPANSION TANK CAP,
INSPECT DRIVE BELT(s),
INSPECT COOLANT HOSES,
INSPECT HEATER HOSES,
INSPECT BYPASS/MISC. COOLANT HOSES/PIPES,
TEST THERMOSTAT OPERATION,
INSPECT RADIATOR COOLING FAN(s)/CLUTCH OPERATION,
INSPECT CONDENSER/AUXILARY COOLING FAN(s) OPERATION(s)
INSPECT RADIATOR & CONDENSER FOR DEBRI,
OBSERVE COOLANT TEMPERATURE GAUGE OPERATION,

Jul 07, 2014 | Ford Excursion Cars & Trucks

1 Answer

How to remove fuel filter


If it is a 7.3diesel you have to open a fuel line and use a fuel gauge in if is 5.4 or the v10 if you look arou.d the fuel rail there is a port to scew a gauge on to it

Nov 03, 2012 | 2001 Ford Excursion

1 Answer

Whats the fuel pressure on a ford excursion v10


Fuel pressure for your 2000 Excursion is 35-45psi with key on and engine off, with engine running the fuel pressure should be 28-45psi

Oct 14, 2012 | 2000 Ford Excursion

1 Answer

Where is the fuel pump relay on 2000 excursion v10


the Fuel Pump Relay is located behind the radio. The radio has to come out to access it.
what a place to mount the relay for an engineering team with the right mind !!?
RADIO REMOVAL HERE

Feb 16, 2012 | 2000 Ford Excursion

1 Answer

2000 ford excursion v10 driving down the road


Honestly you should send it into the dealer. I don't think guessing will help you. Typically it is a dirty connection into the steering column (behind the ignition key) But diagnostics need to be run and a look at the VSS system (through a good scan tool) is needed to confirm.

Apr 17, 2010 | 2000 Ford Excursion

2 Answers

Fuel Filter replacement on Ford 2000 Excursion - V10


1.- For identify the right fuse, check your 2000-Ford-Excursion-Owners-Manual position 112, 20AMP (Maxi Fuse); details in the page 138 and next.

2.- Ford Excursion, Expedition, Lincoln Navigator 2000-2005, Fuel Filter - Removal & Installation

NOTE A fuel line disconnect tool is needed for this procedure.
CAUTION Fuel injection systems remain under pressure, even after the engine has been turned OFF. The fuel system pressure must be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury.
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:
    Negative battery cable
  3. Relieve the fuel system pressure.
    Fuel lines from the fuel filter. Have a drain pan handy to catch any residual fuel once the lines are separated.
  4. On newer models, disconnect the fuel lines from the filter as follows:
    Safety clip from the male hose Install and push the fuel line disconnect tool into the female fitting.
  5. Remove or disconnect the following:
    NOTE Inspect the fuel lines for any damage after the fuel is finished draining. Male and female fittings from the filter Fuel filter from the bracket and the retainer, if equipped. Note the direction of the flow arrow so the replacement filter can be installed correctly.

    0e9d2de.jpg

    Fig. Typical fuel filter mounting along an under-vehicle frame rail

To install:
  1. Install or connect the following:
    Fuel filter into the mounting bracket with the flow arrow pointing in the correct direction Fuel lines to the fuel filter. Align and push the male tube into the female fitting until a click is heard. Pull on the fitting to ensure that it is fully engaged, then install the safety clip.
  2. Lower the vehicle to the ground.
    NOTE When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the Powertrain Control Module (PCM) relearns its adaptive strategy. The vehicle may need to be driven 10 miles (16 km) or more to relearn the strategy.
  3. Connect the negative battery cable.

Hope this helped.

Mar 30, 2010 | 2000 Ford Excursion

1 Answer

2000 Ford Excursion V10 6.8L


HAD SAME PROBLEM THE INJECTOR IS BAD

Jan 19, 2009 | 2000 Ford Excursion

1 Answer

Triton V10 Engine Shudders under load


have your fuel system vacuumed out our excursion did it as well the injectors are not at fault it is the fuel lines

Jul 09, 2008 | 2000 Ford Excursion

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

387 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...