Question about Chevrolet Silverado 2500HD

Open Question

I need a serpentine belt diagram for a 2003 chevy duramax.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
bbtoast
  • 319 Answers

SOURCE: need a diagram for serpentine belt

Click this link, then look at illustration 6-6.

Regards

Brian

Posted on Sep 18, 2008

Ad
  • 314 Answers

SOURCE: serpentine belt diagram for 2003 chevy impala

send an email to chuckie12_87@yahoo.com and I will send the diagram to you

Posted on Jun 23, 2009

  • 20 Answers

SOURCE: Diagram of Serpentine Belt 1998 Chevy Cavalier

diagram should be on the radiator shroud / top of radiator

Posted on Jan 10, 2010

ZJLimited
  • 17970 Answers

SOURCE: Need to have belt diagram for serpentine belt for

2000 CHEVROLET IMPALA - V6 3.4L 207ci GAS FI N E

bfe9804.jpg


2000 CHEVROLET IMPALA - V6 3.8L 231ci GAS FI N K

0719873.jpg


Hope thats helped (remember rated this) Good luck.

Posted on Jan 25, 2010

  • 468 Answers

SOURCE: 2003 Chevy Suburban-replace alternator

Ok, Alternators are a breeze on these things. There are two bolts that hold it on, and 2 sets of wires. If you haven't taken anything apart yet, and the belt is still on it, here's what to do. You will want one of those rubber or elastic bungee cords, about 2 and a half feet long(this makes it easy). Hook that bungee cord to your hood somewhere, so that it hangs down. Hook the other end on the serpentine belt right next to the alternator pulley. If you need to prop the hood up with a stick or something to keep it up, do so. Pull up on the belt, and watch the pulleys. The one that probably has a plastic pulley on it that moves up and down(this is the tensioner) is the one that you'll put a deep well socket in the middle of with a ratchet, and turn counterclockwise. This will make the belt go loose. Now you can work the belt off the alternator pulley, and once you get it off, the bungee cord will keep it in place, so you don't have to look at the diagram. Otherwise, if it comes off, there is a sticker just under the hood either on the fan shroud or the radiator support that has the belt diagram. Now, you can disconnect the battery, pull the rubber boot down off the nut and post on the back of the alternator, remove the nut and wire, and then unhook the wire from the side of the alternator. Now, you can remove the two bolts that hold the alternator on. You Will need to pry the alternator off at this point, as it fits really tightly in place. A socket extension or a large flat screwdriver works really well for this. Once you get it off, put the new one on exactly as you took the old one off. Note, you will have to release your tension on the tensioner at some point; i just ease it down, or if I can pull it off, wedge it somewhere where it won't loosen very far. Remember, on the tensioner, you're not trying to take the nut off. All you're doing is using it to move the tensioner arm. That's all there is to this job. Sometimes it can be stubborn with the prying part, especially getting it into place. Hope this is what you're after, and if you need more info, leave a comment for me.

Posted on Feb 22, 2010

Testimonial: "Great advice on the bungee cord!! Well written advide and easy for a novice to follow. Thanks"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Taurus serpentine 3.0diagram


Robert, Serpentine belt diagram. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How To Install Replace Serpentine Belt Ford Taurus 3 0L V6 1AAuto com
2003 Ford Taurus V6 3 0L Serpentine Belt Diagrams serpentinebelthq com
2003 Ford Taurus Belt Diagram Am Having Problem Getting My

Aug 17, 2016 | 2004 Ford Taurus

1 Answer

I need a diagram for the serpentine belt on a 2003 Rav4


Below is the master help link provided to go through belt routing diagram:---Timing belt, drive belt, serpentine belt, accessory belt, fan belt, engine belt routing diagrams for all types of car models?
Click the link below: ----

http://carbeltrouting.blogspot.in/2012/02/timing-beltdrive-beltserpentine.html
----------This will help. Thanks.

Feb 02, 2012 | 2003 Toyota RAV4

1 Answer

Serpentine belt diagram for a 2003 Chevy unpalatable 4.3


Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

  • 2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.
  • 3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.
  • 4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.
  • 5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.
  • 6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

  • Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

    Sep 21, 2011 | 2003 Chevrolet Impala

    1 Answer

    Belt diagram for duramax diesel


    zjlimited_271.jpg

    Fig. Accessory serpentine belt routing-4.3L, 5.0L and 5.7L engines without A/C


    zjlimited_272.jpg

    Fig. Accessory serpentine belt routing-4.3L, 5.0L and 5.7L engines with A/C


    zjlimited_273.jpg

    Fig. Accessory serpentine belt routing-6.5L Diesel engines





    zjlimited_274.jpg


    Fig. Accessory serpentine belt routing-6.6L Diesel engines




    Hope this helps (remember to rate this answer).


    Dec 20, 2010 | 2000 Chevrolet 3500

    2 Answers

    Need diagram for serpentine belt for chevy imo l s 2003


    Click on the following free direct Link. It has the Serpentine Belt Diagram and Tensioner location for your 2003 Chevy Impala.

    http://www.2carpros.com/car_repair_information/year/2003/make/chevrolet/model/impala/2003_chevrolet_impala_drive_belt_routing_diagram.htm

    GENERAL/Standard Rules to Removal the Serpentine Belt with a Tensioner:
    A. Find the Tensioner(s). (See Diagrams on Link)
    B. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
    C. Remove the loosened belt off one of the other more easily accessed Pulleys.
    D. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

    Standard Rules for Installing the Serpentine Belt with Tensioners:
    a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
    b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
    c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
    d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
    e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.


    Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

    Mar 30, 2010 | 2003 Chevrolet Impala

    1 Answer

    I have a 2003 Duramax. While driving last night


    sounds like you may have coolant in your motor

    Mar 19, 2010 | 2003 GMC Sierra

    1 Answer

    Diagram of Serpentine Belt 1998 Chevy Cavalier


    diagram should be on the radiator shroud / top of radiator

    Jan 10, 2010 | 1998 Chevrolet Cavalier

    2 Answers

    Serpentine belt diagram for 2003 chevy impala


    send an email to chuckie12_87@yahoo.com and I will send the diagram to you

    Jun 23, 2009 | 2003 Chevrolet Impala

    1 Answer

    Serpentine belt


    If you have purchased one call parts place and they can explain, if not when you get one ask them,< also check on bottom fron of hood or radiator cover, there is usualy diagram there.

    Apr 25, 2009 | 2003 Chevrolet Impala

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    325 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6918 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...