Question about 1999 Hyundai Accent

1 Answer

The pedal of my clutch is reaching the floor is that a big problem?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Hyundai Master
  • 959 Answers

Sounds like it could become a problem...
What I would do if it were my vehicle that the clutch pedel was saging to the floor ... I would check the clutch master cylinder for fluid ...
Then I would fill it back up and bleed the slave cylinder ....

Posted on Oct 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New clutch installed. No pedal, stays on floor unless I bring it back up with my hand. No resistance.


`Did it bleed, did fluid come out in a steady stream? Isn't there a spring to bring the pedal off the floor?
Check the linkage of the pedal to rod to the clutch master cylinder, make sure that is all together. Any chance the master has an internal leak and won't build hydraulic pressure down at the slave? If you get it bled, then watch the slave operation while someone works the clutch pedal. The piston on the slave should extend and push the clutch fork enough to disengage the clutch.

Jul 19, 2015 | Nissan Cars & Trucks

2 Answers

Clutch pedal fully extended (up) and won't disengage clutch. Happened relatively suddenly.


This may be two possible issues. If your transmission grinded in the past your transmission may have finally given up the ghost. Also your clutch disk may be broken or worn to the point where you can no longer shift. It seems like the latter your going to have to replace your clutch if your a big on doing it yourself a clutch kit is 400$ at autozone. It may be cheaper online good luck I hope this helps

Sep 03, 2014 | 2004 Saturn ION

1 Answer

How to adjust 95 geo tracker clutch


engaging?
you meant dis-engage im sure.
pedal up is engaged,
pedal at floor dis-engages it.
my guess, is the clutch drags unless i push the clutch pedal 100%
to the floor.
1: bad cable is 90% cause. non last this long.
2: no free play is way too loose.
3: broken lever on the pedal top. caused by #1

all fail modes covered here.
http://www.fixkick.com/tranny/clutch/clutch-on-kick.html

Apr 23, 2014 | Geo Tracker Cars & Trucks

1 Answer

I recently purchased a 2003 hyuandai tiburon GT with 171k miles on it i was on the interstate doing 80 mph in 4th gear at around 6k rpm when my clutch pedal dropped back into the floor board and just...


hmmm... 80mph @6000 rpm is not normal. you are needing a lot of power to produce 80mph. it seems clutch assembly needs replacement. clutch assembly includes clutch disc, fly wheel, and release bearing. might as well check your clutch master if the vacuums are still working properly. this might be the culprit to the stuck up clutch pedal.

after replacing the clutch assembly, you can reach 80mph @ 4000-4500rpm

Aug 06, 2011 | 2003 Hyundai Tiburon

1 Answer

I need to get the clutch cable off a 1997 vw cabrio.How do i get the cable off the clutch pedal


After disconnecting the cable from the engine compartment remove the lower panel on the driver side. Press clutch peddle to floor then reach around the steering wheel column on the gas peddle side. you will feel a plastic guard. reach under guard you will feel the cable on top of clutch peddle. pull cable up and toward back of car.

Feb 13, 2011 | 1999 Volkswagen Cabrio

1 Answer

The clutch pedal on Suzuki vitara two litre V6 1998 goes to about inch of floor before activation. Clutch does not slip just too much pedal travel. Is it possible to adjust it? ...


prev.gif next.gif Clutch ADJUSTMENTS 1997-98 Models CLUTCH PEDAL HEIGHT The clutch pedal height should not be a periodic adjustment but may be checked after components of the mechanical clutch system have been replaced. The proper clutch pedal height should be 0.2 in. (5mm) above the brake pedal height If adjustment is necessary, loosen the locknut and turn the adjusting bolt until the appropriate height is reached. Once set, keep the bolt from turning and tighten the locknut to secure the adjustment. CLUTCH PEDAL FREE-PLAY The clutch pedal free-play should be checked from time-to-time in order to assure proper clutch operation. The proper clutch free-play should be 0.6-1.1 in. (15-25mm). Fig. 1: Pedal free-play is adjusted at the joint nut (2), while keeping the outer cable nuts (3) tightened around the center cable thread portion 7924hg30.gif
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. If the free-play must be adjusted, turn the joint nut (2) located at the transmission end of the clutch cable in or out, as necessary to achieve the proper play.
  3. Once the correct pedal free-play is obtained, check the free-play on the release arm (c), it should be 0.02-0.06 in. (0.5-1.5mm).
1999-01 Models These vehicles are equipped with a hydraulic clutch system. No adjustment is necessary.

Nov 05, 2010 | 1999 Suzuki Vitara

1 Answer

Clutch pedal went too floor pulled back up now solid and not lettin engage gears


It is probably a hydraulic clutch. Check the fluid. From your description, I am understanding that the pedal feels normal but you are unable to put the car in gear when you push the pedal down. You probably have a leaky slave cylinder on the transmission, but it is possible to have a leaky master cylinder (on the firewall, aligned with the clutch pedal). Check your fluid, if it's empty fill it and bleed the system. You probably have a really big air bubble in your clutches hydraulic system. Usually you can get away with not replacing the leaking part for a bit, just keep an eye on your fluid, and save your pennies! Good luck!!!

Mar 05, 2010 | Volkswagen Golf Cars & Trucks

3 Answers

Clutch peddle goes to the floor


Do you mean that stays to the floor because the clutch peddle has to reach the floor. If that is what you mean then probably you need a knew clutch or if it is hydraulic maybe it reflling and dicomression.

Jan 28, 2009 | 1999 Hyundai Accent

2 Answers

Front wheel Drive query


DEar Customer,

your from is that your car is front wheel drive & you have to reset your car clutch point that loose its sensitivity as they had before,

its not a big prib you have to open bonet than make more active clutch wire with streching clutch joints.

THNX

May 17, 2008 | 1991 Peugeot 405

Not finding what you are looking for?
1999 Hyundai Accent Logo

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...