Question about 2000 Saturn L-Series

1 Answer

The battery has a clamp holding it and cant get battery out

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,190 Answers

Hello: You have to remove the clamp, then you can remove the battery. Thank you

Posted on Oct 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hold down clamps will not remove to replace battery, 2002 malibu


First off , the battery cover should be removed and the "hold down" clamp is at the base of the battery and it would be shaped as a large triangle with a bolt through it.
Be sure and remove the negative battery terminal first and then the positive. Installation is the opposite , positive first and then the negative.
The bolt should be loosened enough so that the "hold down" clamp comes right out.
Your saying you can't get the "hold down" clamp removed. Do you mean the bolt will not turn or it turns but not enough to remove the clamp? More information would help.

Oct 15, 2016 | 2002 Chevrolet Malibu

1 Answer

How do you get the battery out of the car? i took the cables off and still cant get the battery out.


Why?

Something in the way you have to unbolt & move over?

Ask a neighbor to look at it

Did you not remove the hold down bolt & plastic clamp

Jul 17, 2014 | 1993 Ford Taurus

1 Answer

Removing battery clamp from 2007 Ford Edge ???


behind the battery is a hold down clamp it normally takes an eight mm socket to remove it and then you can lift your battery out

Jan 03, 2012 | 2007 Ford Edge SEL Plus

1 Answer

I cant find the battery in my grand prix se 1994 pontiac


1. Loosen the four screws that hold down the top of the air filter box. 2. Loosen the clamp that attaches the air filter box to the intake hose. 3. Disconnect the air sensor connector from the top of the air filter box. Note: Secure the connector wire, it tends to drop down and more than once I have had to remove the air filter box to retrieve it. 4. Remove the top part of the air filter box. You may need to twist it to get it to release from the rubber air inlet Hose.
5. Remove the two bolts holding the bottom of the air filter box. 6. Remove the bottom part of the air filter box.
7. Disconnect the negative then the positive battery cables.
8. Remove the three bolts that hold the brace that goes over the Windshield washer tank. 9. Remove the brace.
10. Remove the Battery hold down clamp at the base of the battery.
11. Remove the two nuts that hold the fuse box to the fender well. 12. Remove the two fasteners from the front of the widshield washer tank. 13. Rotate the windshield washer tank away from the battery. You may need to move the tank and lift the fuse box to get the tank clear of the battery. 14 Remove the battery.
To Install reverse the steps.
Time: 5 to 10 Minutes

Jul 16, 2010 | 1994 Pontiac Grand Prix

1 Answer

Himself has tried to replace the battery on the 03 frelander. managed to get the top bit holding the battery off but the bolt holding th batery into the clip won't undo - just spins around any ideas?!


If you are talking about the battery clamp bolts turning, then put a screwdriver in the split of the clamp and try to put turning pressure on the screwdriver and at the same time undo the nut of the clamp bolt. Or if you have a pair of mole grips, clamp the bolt head and undo the nut. Worst case , pry the clamp off the terminal and use a hacksaw and cut the bolt in half and remove it , fit a new bolt after. Hope that helps

Feb 04, 2010 | 2003 Land Rover Freelander

2 Answers

Fitting a new battery


all batteries are clamped into place by one means or another.remove battery cables.remove plastic cover,if equipped.at bottom of battery,locate plastic clamp or 'wedge' with a single small bolt through the center,holding it to the bottom of the battery box.remove bolt & clamp.connect + cable first,then - when reinstalling.

Oct 10, 2009 | 1993 Jeep Wrangler

1 Answer

Cant get the battery out


there is a battery hold down clamp you gotta remove it me and my brother just had done this its at the front bottom of the battery hope u got small hands its a *****

Jan 17, 2009 | 2004 Volkswagen Jetta

2 Answers

WHAT IS THE TRICK TO REPLACING A BATTERY ON A 1992 LUMINA


0900823d8004fd1f.jpg


  • Loosen the battery negative terminal clamp.

0900823d8004fd20.jpg


  • Use a terminal clamp puller to remove the negative cable.

0900823d8004fd21.jpg


  • Loosen the battery positive terminal clamp.

0900823d8004fd22.jpg


  • Use a terminal clamp puller to remove the positive clamp.

0900823d8004feae.jpg


  • Remove the battery hold-down hardware and any heat shields.

0900823d8004feaf.jpg


  • Remove the battery from the tray.

0900823d8004a233.jpg


  • Install the new battery into the tray.
  • Also install the hold-down hardware.

0900823d8004fd23.jpg


  • Install the positive battery cable.
  • Then install the negative cable.
  • When installing a battery, be careful to observe the correct polarity. Reversing the cables destroys the diodes. Proper polarity must also be observed when connecting a booster battery, positive to positive and negative to ground.

0900823d8004feb2.jpg

Art courtesy of Delmar - Thomson Learning.
  • Coat the terminals with corrosion preventative spray, then check the job by starting the car.

Jan 09, 2009 | 1992 Chevrolet Lumina

Not finding what you are looking for?
2000 Saturn L-Series Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...