Question about 2001 Ford Expedition

1 Answer

How to replace the electric mirror control switch. The control that operates the side view mirrors doesn't work. I want to replace it.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Director Badge:

    Uploaded 100 video answers.

  • Expert
  • 159 Answers

This video will show you how to replace your switch.Hope this helps yah. Tony">

Posted on Jan 19, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Wing mirrors will not adjust


Wing mirrors have a certain range of electrical adjustment. Manual adjustment by pushing with fingers can make electrical adjustment inoperative. The solution is to make finger adjustment to get back to the electrical range.

May 22, 2016 | Cars & Trucks

1 Answer

Side view mirror switch control how do I test it to make sure it's working


if it works for the mirror on one side but not the other it is working and the problem is with the mirror or mirror circuit, if it doesn't work with either mirror it is probably the switch. the plug may have come off the back of the switch

Nov 21, 2014 | Cars & Trucks

1 Answer

Both elec door mirrors stopped responding same tme, why?


First, make sure you do not have the mirror control switch in the "neutral" position. If it is, neither mirror will work. If the switch is in the correct position to operate each mirror and neither of them work, the next thing I would check would be the MIRRORS fuse (2 Amp) located in the Body Control Module Fuse Block under the right side of the dash near the blower motor. If the fuse is blown, you probably have one of your mirror circuits shorting to ground. In this case, I would replace the fuse and see if it blows again when I operate each mirror. If one side works and the fuse blows when trying to operate the other side, then you at least know which mirror circuit is shorted and you can diagnose accordingly. If the fuse blows immediately (without operating the switch), or if the fuse is not blown, then you most likely have a defective mirror control switch or a broken wire in the umbilical that goes between the body and the driver's door.

Jan 09, 2012 | 2004 Chevrolet Malibu Maxx

1 Answer

Car running starter sill stays engaged blew fuse for the side veiw mirrors and reverse lamp and problem stopped, is there maybe a relay that controls the mirrors ? or reverse lights that may be sticky and...


Hi,

The problem in the starter would be the relay for the solenoid or the ignition switch that might have been stuck in the "ign" postion.

The side view mirror fuse blows might have been a faulty electrical connection on the wires leading to the side view mirror.

The reverse light, if the bulb is busted, needs only to replace. If there is a new bulb, still does not work, the reverse switch on the transmission might be broken or disconnected.

As you could see, they have connected differently.


Hope that helps you out!

Thanks for using Fixya!

Dec 11, 2010 | Mercedes-Benz C-Class Cars & Trucks

1 Answer

Need a diagram for installing a drivers side electric power mirror on a 1995 mercury villager van


here's 1996, all I have. Please rate.

Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

Removal
  1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
  1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).




  1. Remove the wire clip.
  1. Disconnect the power outside rear view mirror electrical connector.




  1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.




Installation
To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
Removal and Installation
Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
Removal
  1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
  1. Remove the two outside rear view mirror inside mounting hole cover screws.


    Remove the outside rear view mirror mounting hole cover.
Installation
To install, reverse the removal procedure. Mirror Control
Removal
  1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).


May 13, 2010 | 1995 Mercury Villager

1 Answer

How do i replace left door mirior


remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation
  1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
  1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
  1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
  1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
  1. To install reverse Removal procedure.
------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove front door trim panel (23942). Refer to Section 01-05 .
Trim Panels, Door Front—Town Car
Removal
  1. Snap out two door pull strap retaining screw covers. Remove screws.
  1. Remove three screws on front and rear side and center of front door trim panel (23942).
  1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.

    Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
  1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

    Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
  1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
  1. Remove the door trim panel.
  1. Disconnect two electrical connectors.
  1. Remove nut from outside rear view mirror mounting base.
  1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
  1. Remove screw from outside rear view mirror base.
  1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
  1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-

Nov 05, 2009 | 1996 Lincoln Town Car

3 Answers

2003 ford escape. radio and sideview mirrors don't work, but clock in radio does. I checked both panel of fuses.


for radio

Visual Inspection Chart Mechanical Electrical
  • Audio unit
  • Antenna or antenna cable
  • audio speakers mounting/speaker cones
  • Radio ignition interference capacitor, radio frequency interference suppression bond
  • Central junction box (CJB) fuses:
    • 19 (10A)
    • 12 (5A)
  • Battery junction box (BJB) fuses:
    • 19 (40A)
    • 20 (40A)
    • 27 (10A)
  • Connectors
  • Ignition switch
  • Circuitry
  • Audio unit


for mirrors

Visual Inspection Chart Mechanical Electrical
  • Exterior rear view mirror(s)
  • Interior rear view mirror
  • Central junction box (CJB) Fuse(s):
    • 8 (10A)
    • 16 (10A)
  • Circuitry
  • Exterior rear view mirror motor(s)
  • Exterior mirror control switch
  • Heated rear window switch

Jun 28, 2009 | 2004 Ford Escape

1 Answer

My side mirros dont work


The exterior mirrors:
  • are controlled by power controls on the LH front door trim panel.
  • are of a foldaway design.
  • may contain turn signal indicators.
  • may be heated when the heated back window glass is activated.
  • may have a programmable recall memory option.
Driver Seat Module
The power driver seat and power exterior mirrors are controlled by the driver seat module (DSM) only when the vehicle is equipped with the programmable/recall memory option.
---------------------------------------------------------------------
Power Exterior Mirror Operation
The power exterior mirrors are controlled by the DSM and are operational all the time, whether the ignition switch is on or off. Using the power exterior mirror switch, the driver can adjust the driver and passenger exterior mirrors four ways.
-----------------------------------------------------
Visual Inspection Chart Mechanical Electrical
  • Exterior mirror(s)
  • Interior mirror
  • Central junction box (CJB) fuse
  • Circuitry
  • Exterior mirror control switch
  • Exterior mirror motor
  • Interior mirror
  • Driver seat module (DSM)
  • Memory set switch


----------------------------------------------------------------------------------


  1. If the vehicle is equipped with memory exterior mirrors and the concern remains after the inspection, connect the diagnostic tool to the data link connector (DLC) located beneath the instrument panel. Select the vehicle to be tested from the diagnostic tool menu.
    • Check to make sure the program card is correctly installed.
    • Check the connections to the vehicle.
    • Check the ignition switch position.
-------------------------------------------------------------------------------------
  • The mirrors are inoperative
  • Circuitry.
  • Central junction box (CJB) fuse.
  • Exterior mirror control switch.


Apr 07, 2009 | 2003 Lincoln Navigator

1 Answer

Replace driver side mirror on 2001 Nissan Quest


SECTION 501-09: Rear View Mirrors 2001 Villager Workshop Manual REMOVAL AND INSTALLATION Mirror —Exterior Rear View Removal
  1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
  1. Remove the upper speaker.
    1. Disconnect the electrical connector.
    1. Remove the bolts.
    1. Remove the speaker.
  1. Position the watershield aside.
  1. Remove the exterior rear view mirror access panel.
  1. Disconnect the exterior rear view mirror electrical connectors.
    • Release the wiring harness locator.
  1. Remove the exterior rear view mirror.
    • Remove the bolts.
    • Feed the wiring harness through the door opening.

Mar 31, 2009 | 2001 Nissan Quest

1 Answer

Driver side mirror problems


The whole side view mirror has to be replaced.

Oct 15, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
2001 Ford Expedition Logo

452 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...