Question about Ford Crown Victoria

1 Answer

My car is a 2008 Ford Crown Vic Police Intersecptor the Speedo, Tac, and temp guage drop to nothing as if the car is turned off.. ALL of the dash lights turn on, ( Brake, engine, etc.) and a few times the tire light flashes and then stays on. The cluster has been taken out and put back in. The Cluster has been replaced.. The cluster works for a bit then it goes right back to not working. it does this when I'm parked and when I'm driving..

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 23,236 Answers

Check the connectors on the ECU.

Posted on Jun 20, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: where is fuelpump on 2003 crown vic police intercepter

Dear cdkkks,

Replacing a fuel pump in modern cars requires some preliminary electrical, fuel test analysis work. I have noted some professionals indicating you need to run car until gas lines, tank is empty; more than likely, if your fuel pump is defective, you cannot start the car, car is unoperative; you will attempt to start car, starter will turn the engine over rapidly without starting, let's assume you are in this condition.

First we need to test the fuses and fuel pump relay, basically the electrical opportunities on your vehicle, the relay panel is on the fender well, driver side, lift the relay control assembly from the fuse center and press the tab on the end, push down and this will release relays from the cover. This relay control panel includes the PCM power relay (left side in original position) Fuel pump relay (Center) this is the relay you are concerned with and the Air Conditioning relay on (Right). If you have friends, or associates who have electrical equipment to test the fuel pump relay, utilize their help, some automotive shops will provide this service. Checking the relay circuit with a jumper wire, any scrap piece of wire, 16-18 gauge will do; as you are looking directly down at the relay opening, you will note an opening at the 6:00 and 12:00 clock positions, 6:00 is the positive, 12:00 is the neutral, volt meter set for volts will confirm. Open the gas cap from the fuel tank filler pipe, insert the jumper wire and carefully listen for a whirring sound. If there is no sound and you have confirm electrical pump fuses, fuel pump relay is working properly (Voltage is pressure, battery voltage and slightly less voltage at the relay circuit when ignition key is turned on) then we have couple more checks to perform before we replace fuel pump. Let's check the fuel rail pressure on your Ford Crown Vic, obtain a fuel compression gauge with a Ford Schrader valve adapter, check to verify that no fuel pressure exists. If "NO" fuel pressure exists, and we have confirmed the voltage integrity of relay/fuel pump circuit, then we are ready to remove fuel pump. Use a simple gas siphoning kits from your local auto parts outlets to safely remove all remaining gas from gas tank, use appropriate gas tanks to store fuel; safety is the key here, gas and gas fumes are extremely dangerous; use appropriate chemical/gas gloves when siphoning/handling gas.

(A) Park your Crown Vic, perferably in a garage, concrete floor and make sure there is enough room around the back of the vehicle for you to work and move tools around.

(B) Raise the back of your car using a floor jack and support it safely on wheel/jack stands; remember, the driver side rear wheel must be removed in order to remove the fuel tank filler pipe, place your wheel stand (supplement with 2 by material for proper height on frame,slightly forward of rear wheel); safety is the key issue here and I cannot overly emphasize this issue, heavy wheel stands should be supporting the right rear wheel and frame, slightly forward of rear wheel, driver side).

(C) Disconnect the fuel tank filler pipe and the fuel pump connector located above the cross member underneath the vehicle, you must remove the (3) screws on the topside (fuel tank fiiler pipe) and approximately (4) screws on the bottom side, and the (1) screw adapter plate where the fuel tank filler pipe is inserted into the gas tank, top of wheel opening, underneath the vehicle. After these connections are removed, push the fuel tank filler pipe further into the fuel tank, allowing you additional room to lower the filler pipe from it's current position, downward; once you have sufficient clearance, twist, turn left, slightly back and forth movements and carefully pull outward, removing the filler pipe from gas tank. Do not damage the rubber groment in gas tank as you remove the filler pipe. As a note, when you reinstall the filler pipe, insert small amount of vasoline on filler pipe end that is inserted into the gas tank to facilitate the installation process.

(D) Support the fuel tank with a jack and remove the nuts from the holding strap using a wrench or ratchet and socket. Move the strap away and slightly lower the fuel tank in order to disconnect the vapor tube from the tee connector on the right and the vapor line from the canister tube. Discard the fuel tank mounting studs and replace with new fuel tank mounting studs on the reinstallation process.

(E) Unplug the pressure transducer electrical connector located on the top rear corner of the fuel tank.

(F) Clean area around the mounting fuel pump mounting flange. Remove/disconnect the fuel lines attached to fuel pump mounting flange then remove the fuel pump mounting flange mounting bolts in a crisscross pattern.

(G) Lift the fuel pump assembly off the tank. Replace the new fuel pump in the assembly and install the assembly in the tank. Install the flange screws and torque to approximately 89 inch lbs using a crisscross pattern. If no torque wrench is available, tighten to a snug fit and stop.

(H) Afterwards, raise the fuel tank enough to attach fuel lines and vapor lines indicated above, item D. After connecting all lines, raise tank with floor jack to its original position "carefully" and utilize the new mounting bolts, securing straps in their original position and torque bolts to approximatlely 25-30 lbs torque.

(I) Install the fuel tank filler pipe per the aforementiond process reversed.

(J) Review your connections and then carefully lower the vehicle, use a gas container, input 4-5 gallows of gas and start the engine and check for leaks.

Wishing you the very best,

drprice

Posted on May 20, 2009

  • 33 Answers

SOURCE: Replace horn on 2006 crown vic

I believe once you have mounted the horn and connected the wire you will find that the horn wire was cut at (by) the steering coloum that the siren override was hooked to,you will have reconnect this,I hope this helps you

Posted on Jul 04, 2009

dsakrison1
  • 65 Answers

SOURCE: 2000 crown vic police interceptor bypass a/c clutch pulley

you can get a A/C Delete kit for a Ford 4.6 liter. the 4.6 v-8 accessory drive system is all the same. You may also be able to run a line of string around the pullys, take it to your local auto parts store and they can match it up. I recomend the kit,

Posted on Oct 06, 2009

matney68
  • 426 Answers

SOURCE: gages speedo tac all quit. fuses are good

Have you checked it with a scan tool to be sure it is actually getting the information? The instrument cluster do go out, meaning the ribbon on the back.I would check the connection, then turn to a way to determine if it is recieving a signal from ECM.

Posted on Oct 09, 2009

roniecon
  • 6927 Answers

SOURCE: 1997 Plymouth Grand Voyager SE instrument cluster

It sounds like the connection to the cluster is not making good contact.

Posted on Jan 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 crown Vic police interceptor former police


The police package interceptors had a common problem with the fans seizing up. There was a TSB ford released to correct the issue which called for the replacement of the electric fan assembly with an updated fan assembly.

Sep 30, 2014 | 2006 Ford Crown Victoria

1 Answer

How do I get the instrument panel out of a 2008 crown Vic police interceptor


If you bought a former police car, take it to a Ford dealer or reputable mechanic, because there are things under the dash you don't want to mess around with and short something out.

Jun 02, 2014 | Cars & Trucks

1 Answer

2004 2005 ford crown vic transmission interchange


I buy and sell used police cars and everyone tells me, including ford, that they are all year specific except for 2007 and 2008. They are interchangable.

Jan 17, 2013 | Cars & Trucks

1 Answer

Fuse panel diagram 2006 crown vic


The diagram is part of the owners manual, you can access a free pdf copy HERE.

Jun 01, 2012 | Cars & Trucks

6 Answers

I have a 2006 Ford Crown Vic Police Interceptor. I am having a problem with the dash. As I am driving it all the warning lights come on and the speedometer, tach, and odometer all stop working. I have...


Has anyone bothered to scan the IPC (Instrument Panel Cluster) or the GEM (General Electronic Module) to see if there are any fault codes? Does the engine run OK when this happens? I had a Grand Marquis that was doing something similar and the modules had several U-codes. Finally found the problem in the Transmission Range Sensor - it was shorting out the data line.

Dec 02, 2010 | 2006 Ford Crown Victoria

1 Answer

92 crown vic - temperature guage on the dash is not working...


0900c152801e4775.gif

The temperature gauge sending unit is located in the front section of the intake manifold, just to the right of the alternator on the 4.6L engines. Got this from autozones repair manuals


Mar 16, 2010 | 1992 Ford Crown Victoria

2 Answers

2008 crown/vic police,feul guage reads empty,have jumped at tank harness black/orange to yellow/white still reads empty


either a fuse on the fuse block is faulty (not likley if other gages are working),,,,,of the gage itself needs replacing....also the sendind unit at the tanks might be bad bad and not responding to the jumpering.

Feb 26, 2010 | 2008 Ford Crown Victoria

2 Answers

1990 Crown Vic LX Odometer does not work


I think the speedo head is probably good. You need to check the speedo cable and the gear at the end of the cable housing. If the gear is cupped in the center it is worn out. Replace the gear by the color code at your local Ford dealer. The other scenario would be that the gear on the output shaft is worn also. This would require the tailshaft be removed from the tranny and the nylon gear replaced on the output shaft. Good luck.

Mar 12, 2009 | 1990 Ford LTD Crown Victoria

1 Answer

Pulsing feel to right in steering wheel on hard left-hand turns.


What rims are on the car the steel police ones and what tires are on it could be hitting the stops on the frame and where the proper bolts put back in on the rack mounts and did you go with the heavy rack for the police car .Cause when I built them there was an issue with the proper bolts and there was a different rack for the cop cars the to the basic crown vic do to the suspension upgrade on it and the diffrent pump

Mar 12, 2009 | 2003 Ford Crown Victoria

1 Answer

2003 ford crown vic hard steering


i would have to say to check for a relay in your fuse boxes for power steering pressre switch or it may have its own police pkgs have a lot of relays due to all the extras

Sep 10, 2008 | 2003 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...