Question about 1992 Honda Accord

1 Answer

I have oil leakin on top of my spark plug wires in the tube ive changed the valve cover gasket 3 times i even put high heat cilcone over around the spark plug tubes but all it does is slow it down im not burning oil it just sits on the boots any suggestions

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 87 Answers

Two things:

1. Make sure you torque the bolts down to the right specification, which is 83 inch pounds (or about 7 ft lbs). Work opposite end of the cover and start with a lower torque first (like 50 in lbs), then go up to 83. It's just a good practice.

2. If that does not work, get a Fel Pro gasket set VS50365R (pic below). What is special about this set is the really thin o-rings there in the middle. Those are the rocker arm tube seals. You need to take the rocker arms off in order to replace them, but this way you're doing a complete job and you probably won't have that issue again. If you don't want to get the whole set again (since you already replaced most of it 3x over), you can probably just go to a honda dealership and pick up the 4 you need.


i have oil leakin on - 44db60b.jpg
Here are the seals under the rocker arms:

ea6e49b.jpg
If you decide to do this yourself, it's a good idea to get a set of feeler gauges so you can properly gap the clearance from the rocker arms to the valves. Intake valves should be gaped to .010 in, and exhaust valves to .012 inches. Also, yes, you can take the rocker arm assembly off without removing the distributor...just take off that one bolt that is in the way. The torque for the bolts holding in the rocker assembly is 9 ft-lbs for the smaller 6x1mm bolts and 16 ft-lbs for the larger 8x1.25mm bolts. Here is the torque sequence...

94f3f23.jpg

Posted on Oct 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changed spark plugs on a 2004 mazda found oil in the pistons #4#3#2#1 was no oil in it


You didn't find oil in the pistons, you found oil in the spark plug tubes. This is fairly common on older engines. Over time the seals in the valve cover begin to leak around the spark plug tubes. Oil then works it's way into the tube and settles in the bottom.

There is an easy fix. Simply replace the valve cover gasket.

Nov 08, 2014 | Cars & Trucks

1 Answer

Am changing plugs on 2006 aveo. Found oil in the


Yeah, kind of. The valve cover gasket needs replaced. The seals around the plugs go first because of heat. If the oil mark was near the top of the plug boot, replace the valve cover gaskets/seal. If it was near the bottom, slap in the plugs and wires.

Sep 27, 2014 | 2006 Chevrolet Aveo

1 Answer

My 02 galant runs rough when put in gear but in idle runs okay it also surges up and down replaced the plug wires


Okay, lets start with the oil you found on spark plugs when you were replacing them. this oil is coming from the valve cover tube hole area, notice the plugs go into the holes in the valve cover, there is a gasket the goes around the top of the tubes and when it leaks it goes into spark plug hole, the valve cover needs replacing .
this will cause rough idle and running problems, after replacing valve cover gasket the holes must be cleaned, using crab cleaner, spray into holes and use air to blow out . this may need to be done a few times to get oil out .
after oil is removed . then remove spark plugs and wipe them clean.
The next step is to find the air (vacuum leak) , you said you hear it around intake tube. check for cracks or broken vacuum line. this leak will cause idle problems and driving problems,

Nov 18, 2012 | Cars & Trucks

3 Answers

1992 toyota corolla oil leak around spark plug tubes. how is it repaired


You need a new valve cover gasket set. This will come with seals that fit around the spark plug tubes.

Jan 18, 2011 | 1992 Toyota Corolla

2 Answers

I have a mazda millian and my check engine light came on , so i hooked it up to a *** machine and it said, #3 cylinder was miss firing , so i took the #3 srark plug wire off and there was oil all over...


Oil leaked into the sparkplug tube from the round valve cover seal at the top of the tube. Replace valve cover gasket with spark plug tube seals and problem will be solved.

Jan 09, 2011 | Mazda Millenia Cars & Trucks

2 Answers

How do i change spark plugs


get your tools out and learn on the job

Jan 23, 2010 | Daewoo Nubira Cars & Trucks

3 Answers

Oil in spark plug holes


HAD THE SAME PROBLEM WITH MY DAUGHTERS CAR---CHANGED THE SPARK PLUGS AND OIL IN THE HOLES OF THE SPARK PLUGS WIRE TOPS--- CHANGED THE VALVE COVER GASKET AND ITS BEEN CLOSE TO 4 MONTHS AND NO OIL AT ALL IN HOLES---IF YOU LOOK AT THE GASKET YOU CAN TELL IT LET THE OIL OUT---THE GASKET SITS INSIDE THE VALVE COVER VERY SNUGLY--THE OLD ONE WAS VERY LOOSE---AS FAR AS OIL GOING INTO THE SPARK PLUG CYLINDER IT WILL BLOW WHITE SMOLE FOR ALITTLE WHILE BUT EVENTUALLY BURN OFF---HOPE THIS HELPS---DENNIS

Jan 16, 2010 | 2001 Kia Sportage

2 Answers

Valve cover removal of a 2000 montero sport 3.5 v6. I had thought that i removed all bolts and i just can not lift the cover. changing plugs and i ran into a bigger problem plug 3 and 5 had oil in the...


If you are sure that you have removed everything that is holding the cover to the head, you may need to use a bit of force to get it off as it may be glued in place. If your plugs go in through the cover, they must be removed .

Aug 31, 2009 | 2000 Mitsubishi Montero Sport

4 Answers

Oil around spark plugs on 1992 honda accord


Yes the oil can cause the car to lose spark, the oil leak could be caused by the valve cover gaskets around the spark openings, but 9 times out of 10 it is the spark plug tube "O" rings. The top of the valve train comes off of the head, the "O" rings are between the two halves, that will fix the oil leak.

Apr 01, 2009 | 1992 Honda Accord

4 Answers

Oil in spark plug wells I just found out that I also have oil in one of my spark plug wells and need to know if this is a major fix?


not really the valve cover needs replaced get a valve cover gasket kit it will come with the gaskets that cover the spark plugs .if you let it go after a while it will contaminate or spark plugs wires and cause a misfire or your car will start missing.please rate this answer thanks.

Feb 02, 2009 | 2000 Dodge Neon

Not finding what you are looking for?
1992 Honda Accord Logo

585 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...