Question about 1989 Toyota Camry

1 Answer

89 camry got water leaking from around water pump have taken out alternater and removed thermo cover cannot get the timing belt cover off because of engine mounts how do i get it off all bolts taken out.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 2,122 Answers

Place a jack with suitable protection under sump so as not to damage sump and lift just a little to relieve just enough tension to remove through bolt onto body....Regards Johngee

Posted on Oct 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove timing belt cover on 2000 toyota camry 4 cylinder 2.2 litre? i notice the securing bolts around the perimeter. do i access some of these from the wheel bay?


See here for info, p26 and 242.

http://www.turboninjas.com/camry/eg1.pdf

This is for an earlier year model, but is for the 2.2L engine.

You will have to remove the crank pulley, timing belt covers and timing belt, for best access. Unless it is fairly new, I would replace the belt wile you are at it.

Oct 13, 2014 | 2000 Toyota Camry

1 Answer

Do the timing belt cover on a 1996 camry have a seal or gasket that can leak oil, mine seems to be leaking for around that area. If so how to replace the seal/gasket?


The timing cover itself does not seal any oil from leaking. It is just a cover to prevent debris from getting into the timing belt and ruining it.

To find the oil leak you will need to remove the timing cover and inspect the seals behind the cam gear, crank gear, and oil pump drive gear, and the oil pump to block seal. The most common leaks on these are the cam gear.

Jan 31, 2011 | Toyota Camry Cars & Trucks

3 Answers

Where is the water pump located on a 1996 olds aurua the car is over heating


Hi, i would check the thermostat first unless the water pump is leaking as the water pump is where the timing belt is is the timing belt needs removing to get to the pump, take the thermostat out and place it in a tub of boiling water and check if it opens up if it dont then it will need replacing.

you need to bare in mind that it could also be head gasket failure so make sure you get this tested if the thermostat is found to be in working order.

let me know if you need further assistance ok

Sep 14, 2010 | 1996 Oldsmobile Aurora

1 Answer

Yesterday I took my 2000 Toy camry 4 cylinder ,in for new timing belt and water pump. I see they have replaced the pump. but Im suspicious about the belt. Is there a way for me to visually check myself?


Will I'am not sure how you can see the water pump, because the water pump is in back of the timing belt cover and sit in the lower part of the front of the engine, the lower timing cover would have to be remove to see the water pump. about the only way you can check the timing belt, is to remove the two small bolts 10mm, on the top of the timing cover, open it a little with a screw driver and you will see the timing belt, hope this was very helpful.

Aug 19, 2010 | 2000 Toyota Camry

2 Answers

Water Leaking from belt side of engine on a 1996 Camry.


hi, is it just water? or does it look more like coolant? if just water, and seems to only leak when a/c or defrost is used, this would likely be the evaperator drain tube letting moisture out. this is normal. but if looks like coolant(reddish pink, or possibly green) this likely means you have a leaking water pump. the water pump is driven by timing belt which is located behind the timing cover directly behind the drive belts. if/when you go to get it repaired, the timing belt should be replaced at the same time. also, you may want to have the timing belt tensioner, and timing belt pulleys relpaced at this time as well, it's good insurance for any repairs that may be needed later down the road after service. make sure to have the drive belts checked when repairing timing belt, they will be removed during repair, if they need to be replaced due to wear, re-install new ones at no extra labor charge.

Jul 08, 2010 | 1996 Toyota Camry

1 Answer

Change water pump on 1999 Century Buick


GM Century/Lumina/Grand Prix/Intrigue 1997-2000 Water Pump - REMOVAL & INSTALLATION

3.1L and 3.4L (VIN E) Engines
  1. Disconnect the negative battery cable.

  2. Partially drain the cooling system into a suitable container.
  3. Remove the drive belt guard.
  4. Loosen the water pump pulley bolts before removing the drive belt. This should help keep the pulley from turning as the bolts are loosened.
  5. Remove the drive belt. Please see .
  6. Remove the water pump pulley bolts and remove the pulley.
  7. Remove the water pump bolts and separate the pump from the engine front cover.

To install:

1430070.jpg

Fig. Exploded view of the water pump and front cover arrangement-3.1L and 3.4L (VIN E) engines
  1. Clean all parts well. Use care when scraping gasket material from the front cover and the pump. Do not gouge aluminum parts. Clean the bolt threads well. The torque specification is low and if the bolt threads are dirty, an accurate torque is not possible and leaks are likely to develop.
  2. Using a new gasket, install the water pump to the front cover. Install the cleaned and lightly lubricated water pump bolts. Torque to 89 inch lbs. (10 Nm).
  3. Install the water pump pulley and bolts and torque to 18 ft. lbs. (25 Nm).
  4. Install the remaining components in the reverse order of the removal process. When refilling the cooling system, use the proper mix of DEX-COOL® and water. Check for leaks.

3.4L (VIN X) Engine
  1. Disconnect the negative battery cable.
  2. Partially drain the cooling system into a suitable container.
  3. Remove the coolant recovery reservoir.
  4. Remove the drive belt. Please see .
  5. Remove the pulley bolts and separate the pulley from the water pump.
  6. Remove the water pump bolts and remove the pump from the engine.

91d51fb.jpg

Fig. Exploded view of the water pump mounting-3.4L (VIN X) engine
To install:
  1. Clean all parts well. Use care when scraping gasket material from the front cover and the pump. Do not gouge aluminum parts. Clean the bolt threads well. The torque specification is low and if the bolt threads are dirty, an accurate torque is not possible and leaks are likely to develop.
  2. Using a new gasket, install the water pump to the front cover. Install the cleaned and lightly lubricated water pump bolts. Torque to 89 inch lbs. (10 Nm).
  3. Install the water pump pulley and bolts and finger-tighten the bolts.
  4. Install the drive belt, then torque the pulley bolts to 18 ft. lbs. (25 Nm).
  5. Install the remaining components in the reverse order of the removal process. When refilling the cooling system, use the proper mix of DEX-COOL® and water. Check for leaks.

Hope this help (remember comment and rated this).

Apr 04, 2010 | 1998 Buick Century

2 Answers

Changing water pump 2000 ford focus


Changing a water pump is pretty basic. Since the coolant system is a closed system you only need to be concerned with that system. For instance you since you have to mess around with it anyway you might as well change the thermostat and flush the coolant system. Make sure your radiator hoses are in good shape and that's about it.
If you have basic mechanical skills and tools you will have no problem replacing a water pump.


As far as information with the actual replacement there are a number of experts here including myself that could explain how to do it.
However no matter how good our explanations are it just can't compare to a good repair manual.
A repair manual for your car at Auto Zone would likely cost between $12 and $15. It is a great investment if you are going to keep your car for any length of time. When you sell, it shows the buyer you took the time to maintain and repair it right.
I personally like Haynes Manuals.
I hope this helps.

Nov 11, 2009 | 2000 Ford Focus

1 Answer

Replace water pump 02 sportage


I'm going to assume you have the 4WD model..here are the instructions for removal and install:

  1. Drain the cooling system.
  2. Remove or disconnect the following:

    Negative battery cable Lower splash shield Upper and lower radiator hoses Coolant reservoir tank hose Fresh air duct Fan and shroud Loosen the alternator mounting and adjusting bolts Alternator belt Fan pulley and bracket Upper and lower timing belt covers and turn the crankshaft until No. 1 cylinder is at Top Dead Center (TDC). Loosen the tensioner lockbolt and pry the tensioner away from the belt Timing belt Loosen the tensioner bolt Water pump Tensioners from the water pump
To Install:
  1. Clean the surface of any old gasket material.
  2. Install or connect the following:

    Tensioners on the water pump Water pump and gasket. Torque the bolts to 19 ft. lbs. 25 Nm). Timing belt Loosen the tensioner lockbolt and allow the tensioner to rest against the belt. Torque the tensioner lockbolt to 32 ft. lbs. (43 Nm). Upper and lower timing belt covers Fan bracket assembly and fan pulley Drive belt Cooling fan and shroud Position the radiator and torque the bracket bolts to 89 inch lbs. (10 Nm). Torque the shroud bolts to 89 inch lbs. (10 Nm) and torque the alternator adjusting and mounting bolts Position the fresh air duct over the radiator and tighten the retaining bolt 89 inch lbs. (10 Nm) Radiator hoses and tighten the clamps Lower splash shield Negative battery cable
  3. Fill the cooling system.
  4. Start the vehicle and bring the engine to operating temperature. Check for leaks and repair if necessary.
70d0f19.gif

Oct 28, 2009 | 2002 Kia Sportage

3 Answers

91 carolla water pump


No. You don't have to remove the timing belt to change the water pump. Check out the autozone.com website and register. It doesn't cost anything and you will have access to a repair manual for the vehicle. The steps for replacing the water pump can be found there. ( I checked) Hope this helps and best wishes.

Aug 18, 2009 | 1991 Toyota Corolla

Not finding what you are looking for?
1989 Toyota Camry Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...