Question about 1995 Buick Roadmaster

Open Question

How do I change side marker light? Limited is light on the back quarter panel

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The Rear Lamp Failure light comes on, and Ii have no been able to locate where this is located. I do not have an owners manual. I have checked the tail lights, brake lights, even the tag lights, and I am...


Nice SUV, I have the same with 5.2L V8 Limited!!!

Are you sure that there are no lights out?pay attention to the third brake light because it has 3 bulbs and if one is outit will give you that message.also make sure that all of the bulbs are the right ones.

I used to get the "Rear Lamp Failure" message on my '93 Limited after the lights were on for a few minutes... it went away when I changed the rear bulbs to the same brand. The Lamp Outage Module (located in the LR quarter panel, near the fuel filler) is looking for differences in current flow between the left and right side bulbs.

You probably need a new lamp outage module...
CIRCUIT OPERATION
The Lamp Outage Module (LOM) determines if a rear lighting lamp is not operating. When the ignition switch is in the START or RUN position, circuit A1 from fuse 8 in the Power Distribution Center (PDC) connects to circuit A21. Circuit A21 feeds circuit F87 through fuse 5 in the junction block. Circuits F87 feeds the LOM.
- Circuit G46 from the LOM connects to the Vehicle Information Center (VIC) . When the LOM senses a inoperative lamp, the VIC displays the data to the vehicle operator.
- Circuit L90 which feeds the tail lamps and side marker lamps, connects to the LOM. From the LOM, circuit L90 continues to the license plate lamps. Circuits L21 and L22 from the LOM power the tail lamps and side marker lamps.
- Circuit L50 from the stop lamp switch connects to the LOM. From the LOM, circuits L73 and L74 power the stop lamps and circuit L87 powers the Center High Mounted Stop Lamps (CHMSL) . Circuit Z1 grounds the LOM.


If you need tha owners and repair manual about your ZJ Grand Cherokee, just keep in touch and send me one comment.

Hope this helps (remember to rate this answer).

Jan 14, 2011 | 1993 Jeep Grand Cherokee

1 Answer

How do I change the front side marker light bulbs?


Bi-Xenons - 6000K D1S
High Beams - Osram Nightbreakers H7
Fogs - PIAA H11 Yellow Ion
Cornering Lights - Osram Nightbreakers H3
Front Park Lights - High-Powered LEDs with built-in resistors
Front Signal Lights - Sylvania Silverstar 7507A ST (Silver Bluish but lights up Amber)
Front Sidemarkers - InviSilver W5W (Silver but lights up Amber)
Rear Signal Lights - P21W Stealth Bulbs (Silver but lights up Amber)
Reverse Lights - Sylvania Silverstar 7506ST or Error-Free LEDs
License Plate Lights - C5W Error-Free High-Powered LEDs
  • Turn the engine off and approach the side of the porsch with the burn-out side-marker light. If you are replacing both, start at either side; the replacement procedure is the same.
  • 2 Remove the screws from the plastic fender liner. Peel back the liner to access the area behind the fender.
  • 3 Reach your hand inside to gain access to the side-marker light's backing. Push the backing forward to release the side-marker lens; it's held in place by small clips.
  • 4 Grab the lens on the outer side and turn it over to access the back. Gently turn the bulb to release it from the plastic lens.
  • 5 Pull the bulb straight out to remove it from the electrical socket. Insert a new bulb, but do not touch the glass part of the bulb with your hand.
  • 6 Push the new bulb into the side-marker lens. Turn it clockwise to install it. Push the side-marker lens back into place. Apply gentle pressure to the lens to pop it back into its mount.
  • 7 Replace the screws along the edge of the fender liner.


  • Dec 04, 2010 | 2006 Porsche Cayenne

    1 Answer

    How do you get the brake light bulb out of the its holder?


    Welcome to FIxYa.com

    Parts:

    3157 Brake light

    How to Remove bulb:

    Remove the Lamp unit from the end of the quarter panel.

    "Open tailgate to access and remove the two screws that secure the inboard side of the rear lamp unit to the side of the tailgate. (see Figure) Pull the outboard side of the rear lamp unit rearward (away from the end of the quarter panel) far enough to unsnap the two ball studs on the outboard side of the lamp housing from the plastic nuts in the quarter panel."

    Change Bulb:

    See Figure


    Regards, Lee Davidian


    Thank you for using FixYa.com

    Nov 05, 2010 | 2002 Jeep Liberty

    1 Answer

    06 Volkswagen Beetle Convertible Turn signal bulb burned out. How do I change it?


    You didn't specify front or rear so here goes. with ignition key off..... front turn/marker light, remove the screw cover in the lens assembly. remove the screw. Pull the lens assembly out forward. Change bulb and reverse process. If it is the side marker on the front quarter panel it is a little more envolved but you shouldnt have a problem doing it. I can walk you through it .let me know how it goes.

    Aug 26, 2010 | 2006 Volkswagen New Beetle

    1 Answer

    The lower blinking light, how im i suppose to take it out to put the bulb


    1. Use a Phillips-head screwdriver to remove the screw from the top of the fender. (inside the fender, under the hood).

    2. Move the side marker light assembly forward until it pops out of the body.

    3. Turn the bulb holder one-quarter turn counterclockwise to remove it from the lens.

    4. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms.

    5. Put the bulb holder back into its hole in the lens, and turn it clockwise until it locks.

    6. Turn on the parking lights and check that the new bulb is working.

    7. Put the side marker assembly back into the body. Push on the front edge until it snaps into place. Install the mounting screw and tighten it securely.

    Hope this helps you.

    Dec 20, 2009 | 1995 Honda Accord

    1 Answer

    Change left front parking/marker light bulb


    Raise the hood, look at the back side of the marker light, if you can see the socket for the bulb, turn it and it should pull out of the light. If you cannot see the back side of the light and locate this socket, you may have to remove the light assembly from the vehicle to access this socket. Hope this helps.

    Dec 11, 2009 | 2000 Lexus LX470

    1 Answer

    1998 Jeep cherokee Marker (left side only) lights not working


    on 97 and later modles there is a fuse panel located behind a small access panel in the right cowl trim panel

    Jul 16, 2009 | 1998 Jeep Wrangler

    1 Answer

    Tiburon GT Limited Fender Side Marker Bulb Replacement?


    You probably have to access the bulb from the back of the bulb housing. The bulb is probably in a socket which plugs into the back. Twist and pull to remove it.

    May 03, 2009 | 1999 Lexus RX 300

    1 Answer

    How to change front driver side 2004 g35 coupe marker light


    Just pop out the side marker from where the marker meets the fender well and push outward on the side marker. It has a metal clip retaining it to the bumper.

    This entry was in January, most likely you figured it out already.

    Jan 19, 2009 | 2004 Infiniti G35 Sport Coupe

    Not finding what you are looking for?
    1995 Buick Roadmaster Logo

    Related Topics:

    95 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Buick Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8202 Answers

    Are you a Buick Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...