Question about Chevrolet Blazer

1 Answer

Have po740 code replaced ingnition switch still have code tranny is shifting fine this is the only code showing up 2000 chev blazer

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

CHECK WIRNG TO SWITCH

Posted on Oct 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2000 chevy blazer is knocking, but from the front of the motor, has good oil pressure. changed the oil & there was very very minute dirt/shavings. Transmission has been acting up going into 2


Check the water pump in the front of your engine for bearings going out. Have your tranny fluid changed & have the 2 shift selonods replaced, if the tranny is OK.

Feb 15, 2015 | 2000 Chevrolet Blazer

1 Answer

1995 blazer 4l60e trans just rebuilt. Hard 1-2


Sounds like full pressure apply from pcm. Must check for full 12v at trans connector. Also check all ground twice. That is a hard trans to install and things tend to get left loose.

Sep 11, 2014 | 1995 Chevrolet Blazer

1 Answer

What can cuse my 2000 blazer to shift hard than drive fine


IT MAY BE LOW ON TRANNY FLUID OR IT MAY NEED A SHIFTING SELINIOD REPLACED

Jan 24, 2013 | 1999 Chevrolet Blazer

2 Answers

2000 blazer shifts fine 1-3 gears , wont go into overdrive, shows check engine light trouble code po0753 shift solenoid a , any help


OK, let me remember..........the code 753 means the solenoid INSIDE the tranny pan is bad. You don't have 1st or 4th gear, is what I was told, however, you probably WON'T even notice. I didn't. If you are at a stop, and get on it hard, you should be able to tell. If you drive normal, like me, and just accelerate gradually, you would not be able to tell that the truck is not hitting the 1st and 4th gear. You may not recognize a problem, just the check engine light. Your going to have to drop the tranny pan, replace the solenoid, and reinstall the fluid and the pan. The hardest part is, upon dropping the pan, if you don't know what you are doing, you can damage the other solenoids, and if you don't damage any, you may still have a hard time realizing which solenoid is the right one. It would take 1hour at, plus tranny pan gasket and fluid, etc., etc., for a total of about $120. Most transmission shop charge $100 for a transmission oil and filter service. The solenoid was about $20. It is not hard to replace, just unclip the wire harness and solenoid which will be an extra 5 min to the service time.

Nov 03, 2009 | Chevrolet Blazer Cars & Trucks

1 Answer

1997 blazer sluggish in drive reverse is fine


P0740 is TCC circuit malfunction P0753 is shift solenoid A circuit electrical P0758 is shift solenoid B P1406 is EGR pintle position and P01860 is TCC circuit.

Feb 03, 2009 | 1997 Chevrolet Blazer

2 Answers

Transmission slips at 40 km/h


seems to me , the 3rd gear shift range is slipping.
You probably have internal failure.
You should take to transmission shop

Jan 24, 2009 | 2000 Chevrolet Venture

1 Answer

Vw 2000 jetta tdi (a/t shifting problem)


Your right in as much as it shouldnt need complete over haul but a competent auto trans technician to clear the shift fault.It could be a solenoid or check valve that should be able to be repaired with out the transmission having to be removed.

Oct 26, 2008 | 2000 Volkswagen Jetta TDI

1 Answer

I can not get the Auto shift lever out of park


I initially tried to override the Brake / Transmission switch by disconnecting the battery but that did not work. I solved the problem by disconnecting the wiring from the actual gearbox, and manually moving the linkage at the gearbox. After doing that everything was re-connected and now works fine.

Oct 14, 2008 | 2000 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...