Question about 1992 Mitsubishi Diamante

1 Answer

1992 Diamante troubles - electrical

My power antenna broke so I decided to replace with aftermarket. I removed original, tapped into wiring to run the after market. Now my power windows, tachometer, temp gauge, and other sytems which seem to be computer related don't work. Did I fry a fuse or computer?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Start by putting the old one back to see if everything works.

Posted on May 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1992 pajero electrical power drain overnight


use an ammeter to find it

it's easy, with one tool, near impossible with out, (pull one fuse each night, nah that sux)

http://www.fixkick.com/drain/drain.html

Jun 25, 2014 | 1992 Mitsubishi Pajero

1 Answer

2002 Chrysler Town & Country antenna installation


Did the antenna break off in the mount or did the mount break.If antenna broke off in mount I would try drilling and tapping it.If you need a whole mount.Remove plug from back of radio attach good mechanics wire to it undo outer mount when you pull the wire out of the car the mechanics wire will follow afer you get it out put the mechanics wire on the new one tape over the wire to make it a smooth transition and pull mechanics wire inside the vehicle to reroute the antenna wire back to the radio.Be carefull you shouldnt have to pull super hard

Jun 04, 2012 | 2002 Chrysler Town & Country

2 Answers

Where is the power antenna motor located for a 1992 buick regal?


I have not owned a buick for years. However, the one I did have trouble with the power antenna motor was located directly under the antenna. It was in the rear fender housing. I have to remove the trunk lining on the side of the fender. It was mounted a bracket. It was easy to replace as it all comes as a complete assembly. Hope that helped

Feb 21, 2012 | 1992 Buick Regal

2 Answers

My antenna broke off when I went through a car wash, how do I replace it?


if part is still left where antenna was take a pair of pliers and turn counterclockwise(left) to remove old piece left. go to most auto parts stores and they should have an original equipment replacement antenna

Jan 14, 2011 | 2004 Mercury Sable

1 Answer

I was removing the antenna, and it broke off. Do


Depending on if your car has a power antenna or not, you may have to replace the whole unit.

The good news is, no, you usually don't have to replace the wires on most GM vehicles. Open your trunk, remove the insulating carpet from the side of the trunk where your antenna is located , to expose the power antenna unit.

This is a stock photo of what the power antenna unit and kit looks likes.

932828d.jpeg

Unplug the electrical connector from the antenna . Unscrew the plastic ring on the outside of the car, where the antenna rest on the body of the vehicle. Pull the antenna unit inside through the hole to remove.

You can usually get a new one for about $89 bucks at Autozone.

Installation is the reverse of remove. Make sure the ignition key is completely off when performing the replacement. Follow all installation instruction on the package. Improper installation could cause rain to leak in your antenna during bad weather and not be water tight.

May 25, 2010 | 1995 Chevrolet Camaro

1 Answer

Antenna broke


Open up your trunk. Remove the felt cover. Check near the antena motor, there should be a socket that can be unplugged so that your antena does not continue to run.

Mar 08, 2010 | 2001 Mitsubishi Diamante

1 Answer

How do you replace the power antenna on a 1996


You need to remove the plastic inner fender well to get to the motor. Likely you will need to remove the kick panel on the passenger side and possibly the glove box to get to the wires.
I recommend using only a factory replacement (even from a scrapyard) as the aftermarket units are often a real pain to mount. Or, you can use a standard antenna (non-power) and just tape off the plug (cheaper, just not "fancy")
Either way it takes some patience running the antenna wore through the body.
good luck

Feb 16, 2010 | 1996 Chevrolet Caprice Classic

1 Answer

Removing starter on 1998 Mitsubishi Diamante


tap it a few timnes with a hammer.....it should loosen up then u decide .................. gl

Jul 24, 2009 | 1998 Mitsubishi Diamante

1 Answer

How to replace thunderbird antenna


please rate service.

Automatic Electric Antenna
Removal
  1. Lower electric antenna (18850) .
  1. Remove rear retaining screws of RH front wheel splash shield for access to antenna lower retaining bolt.
  1. Remove lower retaining bolt.
  1. Remove radio antenna nut (18865) from top of motor tube and remove electric antenna through fender/splash shield access.
  1. Disconnect signal cable and motor wire connector(s).
Installation
  1. To install, reverse Removal procedure.
  1. Tighten top radio antenna nut to 6-8 Nm (54-70 lb-in).
  1. Tighten lower electric antenna retaining bolt to 5.8-7.8 Nm (51-69 lb-in).
  1. Check operation of electric antenna and radio chassis .

    Automatic Electric Antenna


    1faf511.gif

mast
Mast, Power NOTE: A power antenna mast which is bent or broken can be replaced without replacing the motor and tube assembly.
Removal
  1. Remove radio antenna nut (18865) and radio antenna stanchion (18919) .

    ssd~us~en~file=l6389b.gif~gen~ref.gif

  1. Loosen retaining nut inside tube using 14 mm (9/16 inch) socket, and slide nut part-way up mast.
  1. Raise antenna to run plastic drive wire at bottom of mast out of motor. Note direction of teeth on plastic drive wire.
  1. Saw off damaged portion of antenna mast. Remove burrs from mast and slide nut and contact tube off stationary tube.
Installation
  1. With the teeth on the plastic drive wire facing toward motor on antenna, push end of plastic drive wire of replacement mast assembly down into tube. Push it around curve at bottom of tube until end enters drive mechanism.
  1. Run motor down while pushing on plastic drive wire until about 305 mm (12 inch) of wire has been drawn into the tube. Stop motor and insert bottom of antenna mast into tube. Lower mast.
  1. Slide contact tube and radio antenna nut down antenna mast. Tighten nut to 0.45 Nm (4 lb-in).

  2. Raise and lower antenna several times to ensure proper operation.
651247a.gif

Jul 09, 2009 | 1995 Ford Thunderbird

Not finding what you are looking for?
1992 Mitsubishi Diamante Logo

205 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...