Question about Chevrolet Suburban

1 Answer

I am looking for a column shift "housing support" for a tilt steering wheel for my 1990 Chevy Suburban

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,865 Answers

Hello. Your best bet is to call your local salvage yard, or auto junk yard and they will get one for you. J.

Posted on Oct 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello, thank you for helping. I have a 1990 Chevy truck C1500 with a broken steering column that is a tilt, and I have a floor shift. I found a 1990 Chevy truck C1500 tilt steering column from a standard....


if you have a floor shift and the replacement has a colum shift..you can use the colum and remove the pin that holds the shift arm on..it comes out with a pin remover .. just tap it down and out..the arm slides out..then use as normal..

Dec 27, 2013 | GMC C1500 Cars & Trucks

1 Answer

I disassemled the tilt steering wheel to my 1990 Chevy Suburban because the tilt was loose. The steering wheel moved side to side at the tilt location which was right above the gear shift lever bowl. I...


You will have to remove the lock plate and the turn signal plastic assembly, from inside the column housing, in order to access and tighten up the three hex screws that have come loose, allowing the tilt column to move side to side. I have done this numerous times, in the mid 90's, when the 80's GM tilt columns started to come loose with age. The hardest part is getting that lock plate off, and replacing it, if you don't have a lock plate puller, so make sure you have one or else get one, as it will save you lots of time and fustration. Good luck.

Oct 05, 2010 | 1990 Chevrolet Suburban

1 Answer

How do I disassemble a 1990 Chevy Suburban tilt steering column? Do you have a diagram that I can look at with instructions? Also once I disassemble it how do I put it back together? ( diagram &...


Hi!!
Click on the link to get access to the information you requested, once you uninstall one component, ie. steering wheel, select from the SELECT A CHAPTER menu, on the left of the screen, the next component to uninstall. http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0900c1528008f5f5
Good Luck!! Don't forget to rate this post!!

Oct 04, 2010 | 1990 Chevrolet Suburban

1 Answer

1990 chevy gladiator van steering column has came loose. It is floppy, how and what is the best way to correct this.


I will assume you really have a G10-20-30 van.(half/ 3/4 or 1 ton full size van)
The fifth digit of your vin should be a G.
Not the 2wheel drive pickup indicated.
That being said, your Gadiator is an aftermarket conversion van with a loose column.
This would have to be a loose tilt bowl on the steering column.
After removing the steering wheel and lock plate, you will find four inverted torx bolts that hold the tilt bowl to the column. Two will be backed way out and loose.Remove these bolts and appy loc tite to the bolt threads, then reassemble.

Feb 24, 2010 | 1990 Chevrolet C1500

1 Answer

1990 chevy suburban. The key was turned to auxillary and stuck


hopefully that does not have tilt steering which makes the job somewhat more difficult. the same thing happened with a van i owned. there are small arms inside the steering column that move with the key to move the ignition switch.
to confirm it is broken locate the ignition switch on the column. remove it then turn the key. if the piece that normally moves that switch doesn't... than it is broken.

first unhook the battery.

about the only way to get at it is to remove the steering wheel. there are more parts behind that that have to be removed. then you will get to what is basically and end cap. remove that and slide out the parts and install the new arm(s) mine was a 2 piece.

basically you just need to bolt it back up and reinstall the key cylinder and you are good to go. hook up the battery again and you should have a working vehicle.
the tilt springs can be held together with a c clamp. it is tricky but you will see as you attempt it.

Nov 28, 2009 | 1990 Chevrolet Suburban

1 Answer

Replacing ignition switch on 1976 Dodge D-300. Got the steering wheel off and taken out the circlip holding in the bearing. I''ve loosened the three screws that hold the turn signal housing, but can''t...


Here is what MOTOR says to do. If you have Tilt and/or Telescopic steering wheel the column needs to come off the dash and the mounting bracket removed so the cover on the wire harness can be removed. It is mounted with screws. On the others the wire cover is held on with clips and need to come off. The shift lever has to be full clockwise on all models except Tilt. On Tilt wheels position the gear shift at the midway point. Unplug the wire harness and remove the screw for the turn signal lever and then the lever. If you have cruise, let it hang. Remove the hazard warning switch and upper bearing retainer mounting screws. Pull the switch from the column carefully, guiding the wires through the column opening. Installation is the reverse.Hope this helps.

Oct 25, 2009 | Chrysler 300 Cars & Trucks

1 Answer

1990 c1500


Yes, it will fit.Years that fit are 89 to 94.Appearance may be different it steering wheel between a chev or gmc,but wiring should be a exact fit.Other differences in columns are column shift(auto)w/tilt or w/out tilt wheel or floor shift(standard)w/tilt or w/out.

Mar 04, 2009 | 1990 Chevrolet C1500

1 Answer

Steering column removal procedures on a 1994 grand am manual trans with tilt steering.


  1. Remove Air Bag Disconnect battery ground cable and remove left instrument panel sound insulator, lower trim panel or duct assembly, and steering column collar, as equipped.
  2. If column is to be disassembled, remove horn contact pad and steering wheel
  3. Push back seal to expose flexible coupling, then remove coupling pinch bolt.
  4. Remove lower column support bracket bolt, then the upper bracket to instrument panel support bolts and lower column.
  5. Disconnect column electrical connectors and shift indicator cable, if equipped.
  6. Disconnect shift cable at actuator and housing holder, then remove steering column.
d502e56.jpg

Dec 03, 2008 | 1994 Pontiac Grand Am

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...