Question about 1999 Ford Explorer

2 Answers

Where is the ect sensor located on my 1999 Ford Explorer 4.0 v6

Posted by on


2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Ford Master
  • 17,970 Answers

Most ECT sensors (arrow) can be found on the intake manifold, near the water outlet housing...

Where is the ect sensor located on my 1999 Ford - 798b87d.jpg

Hope helps (remember to arte this).

Posted on Oct 28, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

This is the worst image

Posted on Dec 28, 2012


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: pcv valve :where is it located on a 1999 ford explorer sport 2wd

It is located at the back of the engine near the fire wall. It is gray with a T connector at the top with two hoses coming off of the T and going forward into the intake manifold.

Posted on Mar 07, 2009

  • 6 Answers

SOURCE: Location of Speed Sensor 1998 Ford Explorer XLT

polarcycle is right but there is a speed sensor on the drivers side top of the trans. toward the tail shaft or transfer case. there is as well a sensor inside the trans. itself that is mounted on the web. behind the overdrive band and drum.

Posted on Jul 11, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

P0183 code whats the solution to this code as the vehicle is consuming a lot of gas

looks like p0180-p0184 deal with right fuel bank sensor the down side is explorers only get about 400-450km per tank here on the west coast with all the hills and if you have the 4.0 ltr v6 it is a gas pig of a V6 so as a ford guy start with plugs n wires ect all filters ect that would be a start

Aug 01, 2013 | 2004 Ford Explorer

1 Answer

I cannot find the location of the IAT sensor on a 1999 ford explorer sport v6 4.0

I'am guessing it is part of the MAF Sensor

The MAF has 2 sensors in one,should be in the
ducting, between the air filter and the throttle body

Mar 26, 2011 | 1999 Ford Explorer

2 Answers

Were is bank 2 sensor 1 located 1999 ford exploer

Passenger side exhaust before the catalytic converter.

Mar 14, 2011 | 1999 Ford Explorer

1 Answer

Where is the IAT sensor on a 1999 Ford Explorer SOHC V6?

The IAT sensor and your Mass Air Flow sensor will be one in the same located near your filter box on the intake tube

Mar 07, 2011 | 1999 Ford Explorer

1 Answer

Differences between ECT sensor and the sensor for

i have a1999 ford exp 5.0 and temp gauges are not working andit is hard starting

Feb 16, 2010 | 1999 Ford Explorer

1 Answer

Trying to find out where the temperature sensor is located or maybe its called a switch temperature sensor. I replaced the thermostat and I was told this need to be replaced too

You would only need to replace this if your temperature gauge is not working properly. Just because the thermostat was replaced does not mean the sensor must be too.

There were three different engines offered for that vehicle and there is a separate temp sending unit for the gauge than there is for the computer(PCM). The V6 4.0 SOHC ECT for the PCM and the sending unit for the gauge are both located side by side on top of the thermostat housing. The V6 4.0 EI engine ECT is located on the front of the engine, left of the throttle body, and the sending unit is located in the front of the engine, behind the alternator bracket. The V8 5.0 ECT is located in the front of the engine, below the middle of the ignition coils and the sending unit is in the same area, but toward the driver's side of the engine below the left ignition coil.

It will look similar to this...


Nov 14, 2009 | 1993 Ford Explorer Limited

2 Answers

Where is engine number on a ford explorer xlt v6 4.0 litre 1999

The Engine code should be located on RH Side, Rear, on the Lower Crankcase.

Oct 28, 2009 | 1999 Ford Explorer

Not finding what you are looking for?
1999 Ford Explorer Logo

Related Topics:

646 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers


Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides