Question about 1989 Chevrolet S-10 Blazer

Open Question

My 1989 chevy s10 Blazer has had no back brakes since the day i bought it, the dealer ship says the bleed the lines before we got it but the brake light is on, ive also spent 70 dollars or more on parts for the drum brakes and got it fixed but the brake light is stayed on, we opened the master cylinder for the back brakes and the pedal went straight to the floor but when the while the back breaks were getting changed there was brake fluid in the back passenger side brake. im not sure what else to do and i need back brakes before winter what should i do

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 82 Answers

SOURCE: 1999 Chevy S10 Blazer 4x4. Replacing rear pad's,& Bleeding Breaks

have one person in the blazer pumping the brake pedal and then hold to the floor, crack the bleeder then tighten, release pedal, repeat till all air is out one side at a time, if this does not work then your ABS unit is bad witch if u follow your lines from your master cylinder u will find a black box with a motor on it, or the master cylinder itself is bad, it also can cause u to have no pedal, replace the master cylinder first, most likely cheaper.

Posted on Mar 11, 2009

  • 6982 Answers

SOURCE: leaking clutch 85 s10 blazer

First, unless you have just done some clutch work you should not need to be bleeding the clutch hydraulic system...that shows that it's leaking. There is nothing inside the bellhousing that has anything to do with clutch fluid, so, the fluid you see is either engine or transmission oil (rear main seal or seal on trans input shaft) Could it be that the clutch slave is leaking and it's running down and dripping at the bottom of the housing? (clean it up and check that)

Posted on Jun 17, 2009

wracefans24
  • 1985 Answers

SOURCE: 1989 Chevy S10 Blazer, 4.3L V6. 4wd not working.

under the battery is where you need to check first,then follow it down around the right front wheel well,

Posted on Dec 09, 2009

otis31
  • 1 Answer

SOURCE: 1989 s10 blazer my brakes go straight to the floor like their is

c1a3265.jpgthere is a vacuum diagrsm maby it will help u

Posted on Mar 14, 2010

e-Guru
  • 3917 Answers

SOURCE: pictures or illustrations/diagrams of 1989 blazer heater core

Hi,

Please check this webste:

http://www.youtube.com/watch?v=687B2pspF2w

Please accept if this helped you.

Thanks

Posted on Mar 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 Chevy blazer, lost most of brake peddle and


No reset on 98"s bleed all the lines. Replace all the lines in my opinion...That's what I do. we are talking almost 15 years of rust and fatigue...

Sep 24, 2014 | 1998 Chevrolet Blazer

1 Answer

1989 s10 chevy blazer my brake lights wont go out


Replace the brake light switch on the your brake pedal where it mounts to the firewall.

Sep 15, 2014 | 1989 Chevrolet S-10 Blazer

1 Answer

Chevy blazer brake pedal going to the floor when engine is running


has to be air,try bleeding without the brake pedal,just open
the bleeders and let gravity run the fluid out,takes awhile but works.
(master cyl.cover off )

Dec 25, 2012 | 1999 Chevrolet Blazer

2 Answers

Brake pedal on my 98 chevy s10 is soft


1988 chevy r 3500 1 ton changed out driver front brake caliper
brakes are soft peddle goes to the floor tried to bleed but no brake fluid will come please help

Apr 14, 2010 | 1988 Chevrolet C1500

1 Answer

Just changed rear disc pads and one caliper on 2001 Chevy Blazer...now rear brakes are not working at all...fluid is in lines as it comes out when bleeding...help!


the problem here is in order to bleed the brakes properly u need to have a special tool to open up the ABS high pressure pop-it valves, this special tool will be avail at the dealer or in a generic form at any well equiped front end shop, u just can't bleed the brakes without it, I see this same posted problem over and over, this information is correct, u will need a shop to bleed the brakes

Feb 16, 2010 | 2001 Chevrolet Blazer

1 Answer

My 1989 s10 chevy 4by4 vaccum hoses are not right one hose i dont know where it goes,and when i come to a stop my brakes seem to be holding the truck back.


the 4x4 vacuum hose goes to the canister by the battery. could be the rear end "holding" u back. especially if it is roaring.

May 05, 2009 | 1989 Chevrolet S-10 Blazer

1 Answer

ABS light come on intermitenly on my S10 Chevy


The ABS and parking brake lights kept coming on in my boyfriends 2001 Chevy s10. We took it to the Chevy dealer and they ran a diagnostic on it determining that the ABS module was shot (common problem for them mechanic said). The cost to have it fixed at the dealer was about $750. I found a place in Moscow Idaho that rebuilt the module for $130!!!! YAHOOO! You have to pay about $35 in shipping costs but they returned it to us in 3 days.I was able to remove the module myself and didn't need to mess with the brake lines/fluid--it was simple and took about 10 minutes to remove it. The site steps you through removal/installation if I can do this so can you! Go to www.modulemaster.com to determine if you have an ABS module that they can rebuild. It's guaranteed for 5 years and if we had the dealer replace it they would only guarantee it for 1 year. So go to the module master and save some cash!!!!

Mar 30, 2009 | 2002 Chevrolet S-10

1 Answer

1999 Chevy S10 Blazer 4x4. Replacing rear pad's,& Bleeding Breaks


have one person in the blazer pumping the brake pedal and then hold to the floor, crack the bleeder then tighten, release pedal, repeat till all air is out one side at a time, if this does not work then your ABS unit is bad witch if u follow your lines from your master cylinder u will find a black box with a motor on it, or the master cylinder itself is bad, it also can cause u to have no pedal, replace the master cylinder first, most likely cheaper.

Mar 11, 2009 | 1997 Chevrolet S-10 Pickup

1 Answer

No brake!


also check the brake booster usually when it goes bad the pedal goes to the floor causing no brakes.....try replacing that.....also a vacuum leak could cause that....are you loosing brake fluid at all besides when you bleed the brakes? let me know

Jul 05, 2008 | 1994 Chevrolet S-10 Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

263 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...