Question about 2004 Ford Escape

1 Answer

Do the power steering hoses on the 2004 escape have to be welded on . Because they r pressure lines.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 22,306 Answers

Their special compression fittings ,go to a hydraulic pipe shop and they will repair old one cheaper than a replacement

Posted on Oct 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is pressure in high pressure line for power stearing


Their are two (2) lines coming out of the back side of the pump, one of them will have a hose type clamp on it and be a bit big around than the other, that one is NOT the high pressure line. it is the return line.

Jul 04, 2015 | 2001 Dodge Caravan

1 Answer

On a 99 Olds Alero, in the return lines of the power steering hoses, which place does the high pressure hose attach to?


RETURN TURN LINE GOES TO THE LEFT OF RACK PINION AND HIGH PRESSURE HOSE GOES TO THE RIGHT OF RACK PINION.LOOKING AT POWER STEERING PUMP HIGH PRESSURE HOSE THICK HOSE SCREWS INTO POWER STEERING PUMP.WHILE LOW PRESSURE HOSE HAS A HOSE WITH A CLAMP THE LOW PRESSURE HOSE HOOKS TO TOP OF POWER STEERING PUMP.LOW PRESSURE DONT SCREW INTO POWER STEERING PUMP IT IS HELD IN PLACE BY A HOSE SMALL CLAMP.

Jun 24, 2011 | 1999 Oldsmobile Alero

1 Answer

Was driving 2004 trail blazer and the power steering went out was hard trying to turn wheel pulled over and it was leaking on the driver side it wasnt making no noise it just happen so what should i do...


Sounds like you've lost hydrolic pressure. Did you check the 2 hoses connecting to the power steering pump? I take it, you lost power steering fluid also right? If it was leaking badly, it was the high pressure line that blew, if not, it was the return line. You can have a hose made for you for pretty cheap to replace the hose.

Dec 22, 2010 | 2004 Chevrolet TrailBlazer

3 Answers

I have a 2003 Ford Escape that is leaking power steering fluid. I replaced the power steering pump and hoses but it is still leaking. It only leaks when the Escape is turned off.


It might be the rack and pinion kit (seals)

I had this problem 2 months ago... replaced the powersteering pump 3 times until I convinced the mechanics to look at the rack and pinion. there they found the leak, especially when I turned the wheel.. They first kept telling me there was air in the lines and it would go away. but that never happened.

Sep 15, 2010 | 2003 Ford Escape

1 Answer

How do i change the power steering pressure switch on my 04 dodge ram 1500 hemi? I can't find it.


From the Factory Service Manual, you can get one relatively cheap from www.promanuals.net. Here is a link to your 2004 Dodge Ram Service Manual.

The power steering pressure switch is installed in
the power steering high-pressure hose (Fig. 9).

(1) Disconnect electrical connector from power
steering pressure switch.
(2) Place a small container or shop towel beneath
switch to collect any excess fluid.
(3) Remove switch. Use back-up wrench on power
steering line to prevent line bending.

1425db0.jpg

Oct 02, 2009 | 2004 Dodge Ram 1500

1 Answer

Need to replace high pressure power steering hose on 2004 Monte Carlo SS. Need tips to effectively do the job myself. Tools needed, tricks to make the job easier, what not to do...etc. Thank yiou so much...


Power Steering Line/Hose: Service and Repair
Pressure Hose
Power Steering Pressure Pipe/Hose Replacement (3.8L)
Removal Procedure
1. Place a drain pan under the vehicle.
2. Remove the accessory drive belt.
3. Raise and support the vehicle. Refer to Vehicle Lifting.
4. Remove the tire and wheel assembly.
5. The power steering pressure hose is the lower hose at the power steering gear.
Remove the power steering pressure hose from the power steering gear.
6. Remove the power steering pressure hose from the power steering pump.
7. Remove the power steering pressure hose from the clamps on the power steering gear.
8. Remove the power steering pressure hose from the vehicle.
Installation Procedure
1. Install the power steering pressure hose to the vehicle.
2. Install the power steering pressure hose to the clamps on the power steering gear.
Notice: Refer to Fastener Notice in Service Precautions.
3. Install the power steering pressure hose to the power steering pump.
^ Tighten the fitting to 27 Nm (20 ft. lbs.).
4. Install the power steering pressure hose to the power steering gear.
^ Tighten the pressure hose fitting to 27 Nm (20 ft. lbs.).
5. Install the tire and wheel assembly.
6. Remove the drain pan from under the vehicle.
7. Lower the vehicle.
8. Install the accessory drive belt.
9. Fill the power steering system with power steering fluid.
10. Bleed the power steering system.
11. Inspect the power steering system for leaks.

00d203e.jpg

Sep 15, 2009 | 2004 Chevrolet Monte Carlo

1 Answer

Subaru impreza 1993 power steering leak


YOU CANT USE A REGULAR FUEL LINE ON POWER STEERING AS A HIGH PRESSURE HOSE.BECAUSE POWER STEERING PRESSURE IS 1000 PSI.YOU HAVE TO BUY THE POWER STEERING HIGH PRESSURE HOSE IT HAS NUMBER OF PLIES MATERIAL WEAVES TO MAKE IT STRONG.IT WAS MADE FOR POWER STEERING HIGH PRESSURE.YOU DONT HAVE A BLOCKAGE .THE HIGH PRESSURE HOSE JUST WORE OUT.REPLACE IT .IT SHOULD FIX THE PROBLEM.

Sep 04, 2009 | 1993 Subaru Impreza

1 Answer

Honda crv high pressure steering hose leaking


You need a line wrench or a crow's foot. Power steering lines are hard to deal with. The fittings are fine thread and hard to start.You can cross thread them easly.be carful.

Apr 02, 2009 | 2004 Honda CR-V

Not finding what you are looking for?
2004 Ford Escape Logo

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

fordexpert

Level 3 Expert

5627 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...