Question about Dodge B Series Cargo

1 Answer

I need a Diagram to reference how the position of the Distributor Cap and Distributor needs to be mounted with Pictures

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 22,095 Answers

I can tell you what to do but i dont have access to pictures ,this is from my memory of what i was taught at college 40 yrs ago

Posted on Oct 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is it hard to change distributor on 2000 nissan pathfinder


Hi there;This is for a 2000 Nissan Truck Pathfinder 4WD 3.3L SFI 6cyl


Distributor Cap & Rotor - Removal & Installation


NOTE
The 1996-00 3.3L engines were equipped with a distributor.


Disconnect the negative battery cable.
If the distributor cap is to be replaced, mark the ignition wires for identification and remove them from the distributor cap.
Remove any components necessary to access the distributor cap.
Completely loosen the distributor cap mounting fasteners.
Carefully remove the distributor cap, taking care not to damage the cap seal or rotor, then position the cap aside.
If necessary, remove the rotor retainer.
Carefully lift the rotor off the distributor shaft.
NOTE
Inspect the distributor cap to housing seal for damage and/or cracks. Replace if cracks are detected.




To install:


Install the rotor onto the distributor shaft and tighten the rotor mounting fastener, if equipped.
Position the distributor cap seal on the distributor housing, then position the distributor cap on the housing.
Install the distributor cap by tightening the mounting fasteners in a crisscross pattern. Use care to not over-tighten the fasteners.
Reconnect the spark plug wires, making sure to install them exactly in the same position from which they were removed.
Reconnect the negative battery cable.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 06, 2012 | Nissan Pathfinder Cars & Trucks

1 Answer

97 dodge stratus 2.5 car turns over but does not have spark. There is fuel. I replaced the ECM crankshaft position sensor.


I would start with the rotor and cap. I just worked on one and it was the distributor was bad.

If you need to remove it and rplace it heres how.

Distributor Removal and Installation REMOVAL
  1. Remove bolt holding air inlet resonator to intake manifold.
  2. Loosen clamps holding air cleaner cover to air cleaner housing.
  3. Remove PCV make-up air hose from air inlet tube.
  4. Loosen hose clamp at throttle body.
  5. Remove air inlet tube, resonator and air cleaner cover.
  6. Remove EGR tube.
  7. Remove spark plug cables from distributor cap.
  8. Loosen distributor cap hold-down screws and remove cap.
  9. Mark rotor position for installation reference, then remove rotor.
  10. Remove two harness connectors from distributor.
  11. Remove two sets of distributor hold-down nuts and washers from studs.
  12. Remove bolt and spark plug cable mounting bracket from top of distributor housing.
  13. Remove bolt and transaxle dipstick tube.
  14. Carefully remove distributor from engine.
INSTALLATION
  1. Install rotor on shaft.
  2. Position distributor in engine and ensure O-ring is properly seated on distributor. Replace O-ring if it is cracked or nicked.
  3. Carefully engage distributor drive with slotted end of camshaft. When the distributor is installed properly, the rotor will be in line with previously marked line on air intake plenum.
  4. If engine was cranked while distributor was removed, establish proper relationship between distributor shaft and No. 1 piston position as follows:
    1. Rotate crankshaft until number one piston is at top of compression stroke.
    2. Rotate rotor to No. 1 rotor terminal.
    3. Lower distributor into opening, engaging distributor drive with drive on camshaft. With distributor fully seated on engine, rotor should be under No. 1 terminal.
  1. Install distributor hold-down washers and nuts. Torque to 9 ft-lbs .
  2. Install spark plug cable bracket.
  3. Install two harness connectors to distributor.
  4. Install distributor cap.
  5. Install transaxle dipstick tube.
  6. Install EGR tube to intake manifold. Torque bolts to 8 ft-lbs .

Mar 06, 2011 | Dodge Stratus Cars & Trucks

1 Answer

I need a wiring diagram for the ignition control module and distributor on a 2.8 litre v6 motor


OKAY STANDING IN FRONT OF ENGINE ON LEFT SIDE CYLINDERS FACING YOU IS 1 3 5 ON RIGHT SIDE DRIVER SIDE CYLINDERS FACING YOU IS 2 4 6 LOOKING AT DISTRIBUTOR CAP NUMBER 1 SPARK PLUG ON CAP IN THE 9 OCLOCK POSITION YOUR NUMBER 5 SPARK PLUG ON DISTRIBUTOR CAP IN 6 OCLOCK POSITION .STARTING AT NUMBER 1 SPARK PLUG ON CAP COUNTING CLOCKWISE COUNTING 1 2 3 4 5 6 THATS YOUR SPARK PLUGS WIRES ON CAP TO ENGINE PLUGS. 6 PLUG WIRE ON CAP IS AT 7 OCLOCK POSITION.

Feb 07, 2011 | 1988 Pontiac Firebird

1 Answer

Distributor cap diagrahm for a 1992 dodge dakota 3.9 L what is the correct order for the spark plug wires on the distributor I know the firing order is 1 6 5 4 3 2


Here is a firing order diagram and note the distributor cap latch positions between terminals 1 and 2 and 5 and 4, and let me know if you need any help to understand this diagram or if you require any further assistance.


321004f.jpg

Oct 21, 2010 | 1992 Dodge Dakota

1 Answer

I received a P0340 on my 1995 Nissan Altima. It says I need to replace the Camshaft sensor. The dealers say that my car does not have one in it and that it may be in the distributor itself. Is this true....


They may be right. I cannot find the part. here is what the manual says:


REMOVAL & INSTALLATION The camshaft position sensor is located inside the distributor. On some distributors, the camshaft position sensor is not serviceable (replacement parts may not be available separately). If the camshaft position sensor is serviceable, use the following procedure.

  1. Remove the distributor cap and wires.
  2. Remove the rotor.
  3. Remove the camshaft position sensor cap.
  4. Remove the camshaft position sensor mounting screws.
  5. Carefully remove the camshaft position sensor.

To install:
  1. Position the camshaft position sensor in the distributor and tighten the mounting screws securely.
  2. Install the camshaft position sensor cap.
  3. Install the rotor.
  4. Install the distributor cap and wires.

Sep 27, 2010 | 1995 Nissan Altima

1 Answer

Need wiring digram from spark plugs to distributor cap


Review the Jeep ZJ Repair Manual in the Firing Order (page 10 and 11) for 4.0L 6-cyl and 5.2L 8-cyl.

I really hope hepled with this (remember rated this help) Good luck.

Nov 18, 2009 | 1997 Jeep Grand Cherokee

3 Answers

2001 dodge ram 1500 5.9 camshaft position sensor location?


CAMSHAFT POSITION SENSOR 2001 Dodge Truck RAM 1500 1/2 ton 2WD 5.9L SFI 8cyl The Camshaft Position Sensor is located: Under hood, center, upper engine area, rear of intake manifold, mounted in distributor

If this is helpful.Please leave ositive Feedback. Thanks, SnugglePants

Oct 21, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

Need ignition wiring diagram for 93 z71


It's like a phone number. 1-843-6572 Clockwise rotation of distributor. Number one should be indicated on the dist. cap.cylinders are pass side 1357, drivers side 2468
If #1 is not printed on the cap it is around the 5:30-6:00 position. Unless you are refering to the primary ignition wiring then you can just hop on Autozone and get the wiring diagram from them for free.

Jul 31, 2009 | 1993 Chevrolet K1500

2 Answers

1987 GMC Jimmy Distributor cap and Rotor replacement


A diagram may not be needed as its a reasonably easy fix to do on your own.the distributor ca p will only fit on properly one way because at the base of the cap locaters can only fit the distributor if they line up.When doing the spark plug leads do them one at a time and if nessecary write or mark leads as 1,2 etc .The rotor can only fit on one way but put a mark on the distributor to show where the rotor was pointing when you took it off and if it still points there when the new one is fitted.When changing distributor cap and leads they have to go to the correct place.Pays to mark the outside of distributor cap where the locating bits are On the new and old one.Fit the new cap and rotor then take a spark plug lead and fit to new cap 1 at a time.You can tell by lining up the marks on the outside of the distributor cap when you hold them one on top of the other.Good luck

Oct 20, 2008 | 1987 GMC Jimmy

1 Answer

Need wireing diagram to change 72 nova over to hei distributor


Hey , just take the positive wire from the coil you are removing and feed it to the + terminal on the HEI dist. cap.the other terminal under there is for your tachometer. If you are mounting a master kill switch in the bumper for drag racing- attatch the kill wire to the tach terminal also.
Thats it you just plug the three wire pigtail from the dist. base(pickup) to the cap and you are off.
Remember firing order is 18436572 in a clockwise direction. to find #1 remove #1 plug and have someone"bump" the engine over while holding your finger over the hole-carefull. then line up the slotted mark on the crank pulley with the big notch on the timing indicator. Good luck

Aug 31, 2008 | Chevrolet Chevy Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...